How to Replace the fuel pump on the Chevrolet Cruze 2011 to 2015
Вставка
- Опубліковано 18 жов 2024
- Do you need to Replace the fuel pump on your Chevrolet Cruze (2011 - 2015) but don't know where to start? This video tutorial shows you step-by-step how to do it!
Our Chevrolet Cruze (2011 - 2015) manual covers the petrol engines, and includes videos for some of the most common jobs, which you can see here in this playlist. Get the full manual haynes.com/en-...
What's covered:
Chevrolet Cruze (11-15) Haynes Digital Manual
I appreciate the video very helpful said screw it and just cut a whole under the seat 10x quicker lol
Toyota has had fuel pump access under the back seat for years....THANX GM
Vw ma dostęp od lat 80 lub jeszcze dalej 😂
I think I'm gonna have to pay for someone else to do this. Thank you Haynes.
Your car and your wallet buddy 👌 go out and make someone ele $300 dollars richer 😅😅
Yeah.. I’m going to have someone else do it. Lol
@@daniellegauna8514 ususally I ca n fix stuff on my cruze lol but this look axtra complicated
Thank you sir from jamaica
wagwan my yute
Thank you very much will be doing this soon.
What’s so hard about making an access port?
That would cost $0.10 Lord knows GM ain't got no ten cents!
Good god...if they have to instruct you how to open the hood you probably shouldn't be attempting any repairs.
Is this the same for a diesel engine?
It would have been nice to explain what side to remove the wheel well and collectors I think I'm a mechanic and I know because I have done similar job just being informational
Well, I was thinking the same thing however, it’s more clear that it would be the passenger side because that’s where the filler neck is, and you can see the rear door on the right of the screen and a part of the taillight on the left of the screen.
Buenos días amigo necesito reemplazar la bomba de gasolina de un Chevrolet cruze año 2018, este video sirve para el vehículo gracias
good morning friend I need to replace the gasoline pump of a Chevrolet Cruze year 2018 but I don't know if it is the same procedure in the video
All the in tank fuel pumps are similar.
Solo cambio de flotante. Que bien.
Anyone know where the fuel filter is!?
Im thinking its in that black box attached to the fuel tank….i bended the clips to the box but it doesn’t budge its stuck!
A proved fuel container=empty plastic coke bottle
Is this a diesel?
How many miles u guys getting from these pumps I'm at 80000 and mines went out today
Sorry to hear your fuel pump went out recently. It’s not uncommon for one to stop working at your car’s mileage, hope you found this video helpful.
Makes me feel better lol, thanks. I got to 120,000 and it's starting to sputter. Need to do this sooner than later.
Mine is currently at 213,000. This morning it stuttered and eventually had no engine feedback when pushing the gas pedal. Coasted to a stop on the side of the road pressed gas again after a minute and it picked up. I'm thinking it's a fuel pump but not certain.
@@lucasvbishop hey bro did you end up getting it replaced? Same thing happened to mine and I’m thinking that’s what it is. Also if you did what was the pricing?
Hola , desde Chile, no se vio el cambio de la bomba DE combustible.
Can this be done on jackstands without a vehicle lift? Does anyone know?
Obviously.
Anyone have floating baffles in the tank?? How do you place these back properly?
Yeah mate I had that issue. I'll try make it clear as to how I put them back on.
On the floor of the tank, feel around for 2 separate long moulded bumps. They are side by side of each other and are the only bumps you should feel on the floor. Now sit a baffle on one of the bumps. You should be able to tell which side of the baffle house over the bump and the shorter side goes towards the outside of the tank. Then all you do next is push down on the spring to reduce the height of the baffle and then manoeuvre it to sit between 2 smaller moulded grooves on the roof of the tank. Then repeat for the other baffle, again with the shorter end to the outside of the tank.
Mine fit pretty snug and tight. I have read you could use a chemical resistant glue to ensure they stay put for good.
Hope that helps and not too late.
OK thanks
Good work thank you
But where is fuel Filtre 🤔🤔??
Fuel filter is attached to the fuel pump, as it can be seen in this video. You have to do all this work to get to it. Unfortunately...
Cut under the back seat to expose pump instead. Screw all this
Did you do this? I’m trying to figure out where to cut
@@joeyrossmiller12 yup . Cut a hole
Did anyone have code P0171 and replaced this and code was fixed ? Cause I already replaced so many things and that code is still there
Check valve?
I have that code right now, did you figure it out??
I replaced the valve cover for that code and the PCV in that valve cover was bad. Thanks to JESUS that it was that.
Mazda just has you lift the back seat and the pump is right there! Why the heck would you design this crap!
Advanced Instructions: "Locate a large cliff then get out of the car and give it a final, good shove. Watch as the piece of junk rolls to the edge and off the cliff. Your troubles are over. Finally, resolve to never buy another GM car ever again. Congratulations. Your done". 😮
Yeap no question. GM really sucks
The Haynespro gives the wrong electrical diagram for the Chevrolet Cruze 2.0 diesel. South African model. Disappointing. Using the 14day trial.
This car is so bad you need to remove front bumper to take out the headlamp
Who told you that...??
I appreciate the video very helpful said screw it and just cut a whole under the seat 10x quicker lol
Could you send me a picture of how you did that?
Any pics or measurements where you cut the hole?
@@Theslammedcruze hey lift up your back seat the buldge in the center cut about a 6-8 inch hole and be done use a flat head screw driver and a hammer to knock through the metal good to go I honestly sold it lol was a Pos spent 5k fixing it and drove it 200 miles and it kept breaking down mind you anything that needed programmed or anything like that I would take it to the mechanic but doing anything that did not need programming all myself the car was a nightmare and it only had 89k miles