【Mini4WD】Break-in the tuned motor and speed up!【Mini4Cumaster】

G FORCE Mini Break-In System
→www.gforce-hobb...
Amazon purchase page →amzn.to/3aAiwYS
Mini4wd/MignonCumaster Playlist
→ • mini4wd/MignonCumaster
This is a beginner introduction based on MA!
mini4WD/MS Half Flexible→ • mini4WD/MS Half Flexible
MS flexible with easy remodeling process! It is for those who want to level up from beginners!
mini4WD/AR CHASSIS(basic)→ • mini4WD/AR CHASSIS(basic)
Contains up to the Japan Cup 2019 Tokyo and Niigata tournament!
Playlist homepage
→ / @t-hirokihobbych
Twitter → https: // T_HirokiHobbyCh
Instagram → https: // t_hiroki880706
Mini 4WD "Condel"
→ http: // candelle.club/owner.html? Id = 47014
T - Hiroki official site → https: // thirokihobbych.wixsite.com/thirokiofficialsite
It is a homepage for self-introduction. Please register as a favorite! If you have any request, please contact us from the inquiry forum under the site!
Gmail is here → [e-mail]
Opening finding myself / GoodMorningMom
Ending GREEN / GoodMorningMom
Formed in 2011. Melodic Emo Band from Saitama Prefecture 4 people! GoodMorningMom! !
T - Hiroki will support GMM! / gmm_band
word #mini4wd #Mini4Cumaster #TAMIYA
Text translation is google translation

[@pabloxxx9608]

Thank you

[@soulsplaytv1015]

Thank you for this video very helpful

[@killric13]

Hiroki san in every intervals how many minutes do you give your motor to rest after swapping the clips?

[@kizoism]

Is this applicable to do on hyper,light,sprint,power and ultra dash motor? And after the 10 minutes break in you will clean and put oil to the motor right?

[@hayabusa9289]

Can u make video break in for stock motor?

[@charliepaultompodung5153]

Hiroki thanks for the tutorial video. There is another method that you using another motor to rotate the new motor that you connect with rubber tube. Which one is better???

[@t-hirokihobbych]

I don't know how to use rubber tubes.

[@444gajah7]

Do you think the rev tuned motor still had a winning chance at the tecnical lay out?

[@YMANDRACER]

Here in philippines tune motors rpm can reach 26000 to 30000 rpm 3.0 v

[@markjowel88]

How

[@jmanonas4184]

Mountain dew

[@affanayyash1813]

Can you share it?

[@jomiesy7993]

Hi.. did you put oil before breaking in..?

[@oddycool]

have you break in Hyperdash motor?

[@Heemen_678]

Please guid for lightdash mortor

[@alexanderison3882]

Hiroki san did you clean the motor after the break in process with contact cleaner?

[@t-hirokihobbych]

The internal cleaning of the motor is not done because the wear gets worse.

[@alexanderison3882]

@@t-hirokihobbych hiroki san how about the debris trapped inside the motor?i tried this method and had good results. But i cleaned the motor using contact cleaner after the break in process then put some oil.

[@isekaiemperor]

From my understanding, inside the motor there will be bushings or bearings that has grease packed inside( got the idea from electrical fans and bearings) so if you put contact cleaner,there may ne a chance that you will also dilute the grease inside.
Even if you put oil on the bearings or bushings it will dry out and might cause damage to it. Im not sure tho, but i agree that putting contact cleaner will just worsen the performance and durability

[@hamdanid2140]

What the of aplication rpm ??

[@akarandom1]

what is this wizardry

[@akarandom1]

Giri Rpm checker. Just found it

[@hindiakoto]

I tried the low voltage break-in for 30 minutes. 15 minutes front rotation and 15 minute reverse rotation.
Your battery should be 1.32v. Slave motor is needed.
I achieved 27 km/hr (i don't know the rpm value) in my Torque Tuned 2 using the low voltage break-in method. :)

[@DarkKnight11058]

Can u share how the method?