Electronic Restoration Adventure-The Belmont 636 Radio Receiver!

Поділитися
Вставка
  • Опубліковано 28 сер 2024

КОМЕНТАРІ • 1,3 тис.

  • @MrCarlsonsLab
    @MrCarlsonsLab  6 років тому +108

    To learn more about electronics in a different and very effective way, and at the same time support this channel, go to Mr Carlson's Patreon page, click here: www.patreon.com/MrCarlsonsLab

    • @richyrich1504
      @richyrich1504 6 років тому +12

      How do I send you an email ? I have a question about something. I have asked the question on a couple videos but I think it's been missed. I'm sure it will be easy for you, just would appreciate your advice. Thanks Mr. Carlson.

    • @electron-1979
      @electron-1979 6 років тому +3

      Good work pointing out GFI/RCD issues if you bridge earth and neutral.

    • @reidcircuits826
      @reidcircuits826 6 років тому +4

      Oh, so I'm not the only one that says "Hake'o".

    • @manolisgledsodakis873
      @manolisgledsodakis873 6 років тому +2

      I didn't see you resolder the I.F. cans.

    • @basinstreetdesign5206
      @basinstreetdesign5206 6 років тому

      Hi Are you going to drop into at EPTECH in Mississauga this year? If so I'd like to shake your hand. I have no connection with the show except as visitor.

  • @ChiP2sumP
    @ChiP2sumP 5 років тому +5

    I grew up with the knowledge that if you got shocked from an appliance you unplugged it and flipped the plug 180 degrees and plugged it back in...you probably would not get shocked again...lol. For the longest time, I hated the new plugs that would not fit into the house outlets... Then I finally got it, and actually that kind of started me on my electronics journey.
    I must tell you that my absolute awe of your knowledge of old radios and old electronics is truly astounding.
    I remember my first project in my electricity class..they did not call it electronics...was to build a one tube power supply, and then we built a one tube radio receiver powered by our previously built power supply...I did poorly in these classes in the lab part because I could not find things like a cigar box nor the fine wire required for wrapping around an oatmeal box. Still, I managed to pass because I got a basic understanding. And, I found my hobby that is still fun for me today. I am now unable to fix or tinker with radios or computers any more due to my bad eyes and shaky hands...but that does not mean that I have lost any of my enthusiasm for the hobby. This is why I enjoy your videos so much. Keep up the great work and know that there is at least one old guy out there that really appreciates what you are doing.

  • @billwilson8962
    @billwilson8962 5 років тому +3

    I used to build Heathkits with my grandfather. He was very patient and kind, and a great teacher, too....much like you. Thanks so much for sharing your passion and knowledge with the world. We are better off for having seen these videos.

  • @Bunjamin27
    @Bunjamin27 6 років тому +258

    The UA-cam algorithm gets one right every now and then! :) This channel is one of the best suggestions yet!

    • @OldePhart
      @OldePhart 5 років тому +5

      Same here - no idea why the UA-cam Overlords thought I would like this based on my existing choices, but they were right.

    • @zacharystrong
      @zacharystrong 4 роки тому +7

      I don’t know what it is about his videos, but I can watch them straight through for hours. I often watch them to go to bed to. The technical nature keeps my mind busy and from from obsessing about things that keep me up at night otherwise. I keep hoping if I listen to him enough his knowledge will be imparted upon me.

  • @ricknelson947
    @ricknelson947 6 років тому

    As an old Motorola bench tech, I spent over 15 years working on old tube sets not just Motorola’s. Old Bakelite receivers were my junk food. Then in the early 90,s they (tube sets) just stopped coming in and I moved to international field tech support. I really miss working on them. Your description as you progressed, brought back that familiar burnt dust smell for a couple of hours that all old tube sets just have. Thank you for that Sir. I might add that I have over the years worked with some of the best in the industry. I would have no problem setting your workmanship right next th theirs.

  • @paradust
    @paradust 5 років тому +5

    It's Friday evening. I am drinking wine and watching Mr Carlson's Lab. Life is good.

  • @wollaminfaetter
    @wollaminfaetter 5 років тому +114

    I have absolutely no idea what you are doing, i just enjoy to see a serious guy doing what he does best. These videos are amazing :)

    • @BruceNitroxpro
      @BruceNitroxpro 3 роки тому +3

      Ole Kristensen , Once you have Ohm's Law under your bonnet, you can move on to Mr Carlson's Lab series in good order. You will understand what happens when the dust is blown away and the eye can pick up the stuff he talks about so fervently.

    • @nyckhampson792
      @nyckhampson792 5 місяців тому +1

      Yup , he's amazing ....and same here , but learning re capacitors turning bad , replacement of , transistor values, which most capacitors were ,and the tubes are awesome....

  • @edwardquaranta6903
    @edwardquaranta6903 3 роки тому +2

    Mr Carlson, you are an electronics genius. Thank you.

  •  6 років тому +2

    Fine fine fine. Few things in life I enjoy more than seeing old machines...whatever they may be...that have been bodged by a succession of ham-handed "repairers" brought back to life by someone who's truly competent, and understands what he's doing. This was one of the best things I've watched in ages.

  • @ianbutler1983
    @ianbutler1983 6 років тому +23

    Paul's videos are some of the very few on YT where I can always say "the longer, the better." I love these 2 hour marathons. Thanks Paul, I know that producing a 2 hour video, especially one of your quality, is time-consuming.

  • @itsasecrettoeverybody
    @itsasecrettoeverybody 2 роки тому +4

    For some reason youtube recommended this video to me, 4 years after it was released... Well, beautiful restoration of an old electronic piece of art, will definitely watch more.

    • @MrCarlsonsLab
      @MrCarlsonsLab  2 роки тому +1

      Glad you enjoyed David!

    • @itsasecrettoeverybody
      @itsasecrettoeverybody 2 роки тому

      @@MrCarlsonsLab I'm already a sub and I'm watching more videos. Great content, very professional. You put a great amount of dedication in your projects and it shows on the videos and in the final results.

  • @matthewjackson9615
    @matthewjackson9615 4 роки тому +2

    I didn't even come to understand why this particular video had such an appeal for so many viewers including myself. I had to think it through and then it finally came to me. This wasn't just a restoration, it was resurrection. There is something deep in the human psyche concerning resurrections. You took something old and dead and brought it back to life. When you finally fired up the radio and the tubes began to glow , it was almost spiritual. You must have known this in advance because this was , in my opinion, your greatest video ever.
    Plus, I just loved the way you had to work with all those waxy electrical components and that gnarly wiring. It was like watching a highly skilled surgeon at work performing a transplant.

  • @truefilm6991
    @truefilm6991 2 роки тому +5

    Just love late 1930s American Art Deco design. Looks like a prop straight out of a 1940s film noir, with Humphrey Bogart and Edward. G. Robinson. This needs a Western Electric Model 302 telephone right beside it. Wonderful restauration and, as always, an excellent walk through! Thanks for doing this!

  • @kaylarosa4252
    @kaylarosa4252 4 роки тому +4

    I haven't the slightest clue what you're talking about but your voice is so soothing and relaxing I love watching your videos to wind down or go to sleep... you are great at what you do and I can tell you love it I hear the joy in your voice... just wonderful! Thank you

    • @zacharystrong
      @zacharystrong 4 роки тому

      Currently in bed watching drifting to sleep. 3-4 nights a week... it’s like a noise maker that entertains you until you’re ready to sleep

  • @tarstakars
    @tarstakars 6 років тому +3

    I really appreciate the fact that you restored this vintage radio. I like to see people keep equipment like this alive and I have a lot of respect for you sir. I also really appreciate it the way you praised the people of the past for their attention to detail and the quality of the construction. Keep up the good work you are one of my favorite UA-cam channels.

  • @raymondheath7668
    @raymondheath7668 6 років тому

    IF alignment was always a bugaboo for me back in the 70's, but you make it look so easy

  • @tracylemme1375
    @tracylemme1375 4 роки тому +1

    In the early 1960s I made a 5 tube superhet radio in hi school electronics class. Such a clever concept. Simple but very effective. From the 1930s into the late 1960s these radios ruled. How many viewers remember the vacuum tube checkers in the supermarkets

  • @willierants5880
    @willierants5880 6 років тому +6

    So glad I got to sit right next to you in the lab Mr. Carlson. You have the best seats in the house. This was a real treat. Also give your wife a shout out for her awesome stills. Always an inspiration.

    • @MrCarlsonsLab
      @MrCarlsonsLab  6 років тому

      Thanks Willie, she will appreciate the compliment!

  • @sitandfish
    @sitandfish 6 років тому +16

    Mr Carlson, you posted a 2 hour video covering a subject that I have zero understanding of. And, I watched EVERY second.

    • @1959Berre
      @1959Berre 6 років тому

      He sure knows how to bring it.

  • @Funkylogic
    @Funkylogic 6 років тому +2

    Such a beautiful piece of history restored by a true craftsman. Most people would not see beyond the Bakelite.
    Thanks for being the Mr Carlson that is the patient bloke that identifies gems like these and gives them justice.
    You give the magnificent gift of delivering the verisimilitude of the engineering prowess that has long passed away from the older generation of blokes I had the privilege to work with when I was very young.
    You place these things in a real temporal manifold for people, because you bother to explain the history.
    You blow the doors off what most people think a university lecturer is meant to be.
    By doing the rebuilds the way you do, you really take people back in time again.
    Thanks so much for these they are wonderful.

  • @pietersleght8235
    @pietersleght8235 6 років тому

    beautiful! my Dad built a radio with tubes during WW2....a couple of them fell out many years ago but i still have it and love it..

  • @fardellp
    @fardellp 6 років тому +26

    A magnificent restoration. I remember my Grandad loved to repair (really) old radios. I saw him once wind a new coil with Litz wire as one of the "pancakes" on a little regeneration receiver he made, where the two "pancake coils" could be rotated together or apart from one another to get the best sensitivity. He had a curious tool to wind the coil - it looked like a sock darning "mushroom" made of wood but had two series of short metal spikes around the circumference. He would wind the wire around and in an out of these spikes to gradually build up a "high Q" coil (which latter meant nothing to me at the time). I'm so glad that you are keeping this tradition alive. I still have that coil winding tool as a treasured posession.

    • @BruceNitroxpro
      @BruceNitroxpro 5 років тому +1

      diymostthings, You might consider making a video about your winding tool and how it is used. This would be a valuable tool to the people here! de KQ2E

  • @bostedtap8399
    @bostedtap8399 6 років тому +179

    An absolute brilliant electronic and mechanical restoration Mr Carlson. I doubt many others can achieve your experience, technical expertise and demonstration techniques.
    Sincere regards from the UK.

    • @superpeluso1
      @superpeluso1 6 років тому +2

      Bosted Tap quit brown nosing

    • @bostedtap8399
      @bostedtap8399 6 років тому +4

      @@superpeluso1 most interesting comment.

    • @TehWever
      @TehWever 5 років тому +2

      curiousMarc channel shows some real knowledge and experience too. check it out

    • @bostedtap8399
      @bostedtap8399 5 років тому +3

      Thanks for the recommendation, it looks quite good.

    • @matthewjackson9615
      @matthewjackson9615 4 роки тому +3

      I was impressed also, that was some pretty nasty looking wiring and circuitry he had to sort out , diagnose and fix.

  • @mikus4242
    @mikus4242 6 років тому

    Thanks, I really enjoy your videos and that you don't rush the video and cut it down.

  • @EternityofNight
    @EternityofNight 6 років тому

    This was a fascinating journey, steady and methodical problem solving won the day.

  • @mathewmcgill6266
    @mathewmcgill6266 6 років тому +3

    I was an Air Force metrology technician during the 70s. I used and repaired most of the equipment seen in the opening scene. I grew up when tubes were being phased out and transistors were coming in. This brings back a lot. I use to repair quite a number of those old radios, as they were either being thrown away or held onto. It was a great time to get into the field.

    • @JerryEricsson
      @JerryEricsson 5 років тому

      Yes indeed, I was in the Army at that time, we were always getting TV's and radios from the officers, who were convinced that anyone in communications knew how to repair them. I still have scars where I discharged the wrong cap with the wrong part of my body.

  • @JerryEricsson
    @JerryEricsson 5 років тому +3

    I remember my Great Uncle owned one of those radio's, he had it setting on his kitchen table. Living atop a hill, in a small one room shanty, the radio easily filled the whole house with music, and he did love his music. I used to walk to his house every morning before school, empty his slop pail, and carry in coal for his coal stove, and take out the ash from the night before. In the days when there was no school, this would be followed by several games of rummy, that radio playing it's warm toned music in the background. Funny how just seeing another radio like his sort of brings him back, at least in my memory, he died in 1969, the year I married my sweetheart.

    • @MrCarlsonsLab
      @MrCarlsonsLab  5 років тому

      Thanks for sharing your story Jerry!

  • @mleeriley3977
    @mleeriley3977 5 років тому +1

    Mr Carlson, I really enjoy watching your videos. I am an IT tech ( have been for 40 years). I like your manner of protocol when repairing these radios. You also have a great voice for videos! Thanks for your serious efforts!

  • @knottreel
    @knottreel 6 років тому

    Bravo! Excellent video. You are a very good teacher and presenter.

  • @ChozoSR388
    @ChozoSR388 6 років тому +3

    I have to say, when I saw that this video was close to 2 hours, I got _REALLY_ excited! Far too many videos about old radio restoration are far too short, far too often. Settling in with a cup of coffee for this one :D

  • @RuneTheFirst
    @RuneTheFirst 6 років тому +7

    These were also sold in great numbers between 1946-49 under a variety of brands and cabinets. Belmont made them for Wards, Speigle, and other house brands. There were even wood cabinets. I think they kept the same design throughout, just using more modern resistors. IIRC they also kept the same (octal) tube lineup. You got really lucky finding one of the early ones. I'm glad someone who respects it got it.

  • @sgit1
    @sgit1 Рік тому +1

    That cabinet is an art-deco beauty.

  • @truck9moon100
    @truck9moon100 6 років тому

    You are a very special and gifted person. Thank-You.

  • @YanickT
    @YanickT 6 років тому +6

    I learned a lot on old electronic with your restoration videos. I just fixed an old luxman lv-105 (1984) last week. A hybrid amplifier of my friend. The local shop here said to him:" the tubes are gone need replacement and 400$". I said:" bring it to me please!!!" I re-watched you tube video and a i was full trianed :) Diode bridge was open so the heater tube was not heating. Replacing a bunch of old electrolytic capacitors, find a short between 2 solder on a transistor. And that's it. Tubes was good and the sound of this amp is very good. 35$ :) Thank you Paul :) Take care!

  • @bergarteric5713
    @bergarteric5713 5 років тому +14

    Mister in my contry ( France ) we have a word for your job : " en etat de l'art " state of the art !!! brief beautiful job with love for the machine and a perfect mind for the restoration I have 59 years ols and with you i take a lesson ... i love that please continue your video and thanks for the share .... Eric from france

  • @tinydancer7426
    @tinydancer7426 4 роки тому +2

    Watching as you worked on this radio brought back memories. My dad was self employed with a TV, radio, etc. repair business. Most repairs were able to be done in the customer's home. He had a shop where he would take and work on the really involved repairs, but many times customers would bring small items (radios and portable record players and small easily portable TV's) to our house. I loved hanging out at the dining room table where he would work on them and, completely fascinated, watched as he would take the items apart and put them back together. To me, he was working magic.

    • @MrCarlsonsLab
      @MrCarlsonsLab  4 роки тому

      Thanks for taking the time to share your story!

    • @tinydancer7426
      @tinydancer7426 4 роки тому

      @@MrCarlsonsLab When we were cleaning out my grandma's farm house (the house my mom grew up in) we found a variety of old radios in a cupboard. The one I snagged had a very much art deco veneered case ...... and had been powered by a battery ...... a very large battery. Don't remember much about the "guts" of the battery, but I had it for years, trying to find someone who could/would (if possible) convert it to run off house power. Could not find anyone who even wanted to investigate for me if it would have been possible. All I heard from them was, "you won't be satisfied with the sound even IF I can/could be able to do it." Alas, I shall never know. I donated it to a shop (they accepted it knowing it needed a ton of work) and hopefully someone else is loving it. I too wanted to be able to listen to AM programs, particularly at Xmas time, or even listen to a baseball game, in the evening, enjoying the ambience if the amber glowing from the dial. I subscribed to your channel. I thoroughly enjoy these "fix'em up" youtubes. I love seeing old quality build abandoned items brought back to life. What becomes of the radios that you repair?

  • @tunafish3216
    @tunafish3216 6 років тому

    Now that radio is worth a lot of change.
    Very cool for me to watch the whole video.
    Thanks

  • @Shim267
    @Shim267 6 років тому +351

    You're like the Bob Ross of electronics.

    • @TheRealSmithFamily
      @TheRealSmithFamily 5 років тому +12

      But Canadian! ;)

    • @Richard31406
      @Richard31406 5 років тому +3

      haha I was about to post that same thing lol!

    • @scubaman2546
      @scubaman2546 5 років тому +1

      @@TheRealSmithFamily ...in Vancouver, British Columbia.

    • @RoughJustice2k18
      @RoughJustice2k18 4 роки тому +1

      He would be like the Bob Andersen of vintage electronic restorers.

    • @patrickpoer4643
      @patrickpoer4643 4 роки тому +1

      I know what you mean he is very soothing.

  • @hadireg
    @hadireg 4 роки тому +7

    That warm backlight and the presets buttons system makes me time travel to those old days :) RESPECT! thanks Paul for all this knowledge shared! I feel sorry for ppl who cannot feel how much of mind beauty there is inside a bakelite box like this!

  • @DrNoahBoddy004
    @DrNoahBoddy004 4 роки тому +1

    Your gift, in my small, but wondrous mind, can't begin to be quantified Mr .Carlson. I have several components in need of restoration and I would only entrust them to you. Your deep esteem of this science is not once missed by this viewer. Please continue your treasured work. -Scott Strother

  • @macelius
    @macelius 2 роки тому

    I love how these were built on a solid chassis and placed inside whatever case, in stead of everything being attached to the plastic inside.

  • @bearbon2
    @bearbon2 5 років тому +3

    I'm an old radar tech and I love to hear you use the term cycles instead of hz. just the way I learned it in tech school back in the 1960s. You're a brilliant engineer and I just discovered your channel and subscribed. I was never a top electronics whiz but I know enough to enjoy your videos.

    • @MrCarlsonsLab
      @MrCarlsonsLab  5 років тому

      Thanks for your kind comment!

    • @abelincoln7473
      @abelincoln7473 4 роки тому

      Ya know thats a funny kinda thing... I'm not old school trained, we were very much taught to use hertz. But anytime it was radio related it was just easier to describe it as cycles.

  • @armandcorpolongo
    @armandcorpolongo 6 років тому +5

    Outstanding video and so helpful for both experienced and amateur radio restoration fans. Excellent choice of radios - love the looks and performance. Thanks so much for sharing your knowledge and expertise.

  • @clasmir5281
    @clasmir5281 4 роки тому

    Boy this bring back memories. Back in 1975 I restored a short wave radio with tubes that are much older design than these. Luckily the unit only needed minor repair compared to this unit. Thank you for this video.

  • @MusicalBox
    @MusicalBox 6 років тому +1

    Such a satisfying video to watch. This gem from the past couldn't ask for better hands to restore it. Thanks for sharing.

  • @inductorbackemf7204
    @inductorbackemf7204 6 років тому +6

    Looks like i have the next 2 hours to sit back and relax,Paul thanks so much for the time you put into these videos i understand how long it can take.
    Alex.

  • @harrystevens3885
    @harrystevens3885 6 років тому +14

    Notified after two minutes and then find 2 hours of electronic joy to watch later on my new 43 inch smart TV.......Oh the joy!!

    • @rimmersbryggeri
      @rimmersbryggeri 6 років тому +2

      Only 43? Was this video posted on patreon in 2013? LOL

    • @benbaselet2026
      @benbaselet2026 6 років тому +1

      That would be pretty modern compared to the gear usually present in the videos.

    • @abc-ni9uw
      @abc-ni9uw 6 років тому +1

      Try it on my 72 inch bang and olufsen

    • @rimmersbryggeri
      @rimmersbryggeri 6 років тому

      The information is no less redundant because the number is larger.

    • @harrystevens3885
      @harrystevens3885 6 років тому +1

      rimmersbryggeri Now why would I want a huge TV in a small room unless it was to brag about ........

  • @Lee-NN7X
    @Lee-NN7X 6 років тому

    That extra bulb really made a difference...Very nice Paul...thanks

  • @Al-Fiallos
    @Al-Fiallos 5 років тому +2

    You captivated me for the entire video from start to finish. It called to mind the times when I was growing up that when the TV went on the fritz I would pull all the tubes out, take them to the drug store, use the vacuum tube tester and buy the replacement for the defective tube. You are a true teacher.

  • @zetacon4
    @zetacon4 6 років тому +4

    This video was my favorite so far. I plan on watching many more of your restoration themed videos. Love all the technical details. I grew up learning all this theory and put it into practice on old radios and TVs of the 50s. I even found good methods to repair the speaker cone paper so the sound would be normal again. There was so much to learn working with these oldies. Talk about nostalgia! That is another huge plus for enjoyment watching your restoration videos. Thank you so much.

  • @kane100574
    @kane100574 6 років тому +11

    Fantastic! beautiful radio! I truly appreciate your dedication to detail as well as your Patreon content! One of the best channels on UA-cam.

  • @andrzejtomaszewski5357
    @andrzejtomaszewski5357 4 роки тому

    WITAM. GRATULUJE WIELKIEJ WIEDZY , ZNAJOMOSCI TEMATU, OD EPOKI LAMPY ELEKTRONOWEJ, DO CZASU W KTORYM TERAZ ZYJEMY. POZDRAWIAM Z HOLANDII ANDRZEJ.

  • @stevenstewart5980
    @stevenstewart5980 5 років тому +1

    What a treat to watch you bring this 1930's beauty back to like-new condition!
    I just love watching and learning from you Mr. C.!

    • @MrCarlsonsLab
      @MrCarlsonsLab  5 років тому

      Thanks Steven, I'm glad you enjoyed!

  • @redemptusrenatus5336
    @redemptusrenatus5336 6 років тому +5

    SEALDTITE.... to keep the leakage IN! .. That never ceases to make me burst out loud with laughter. Love watching these :D

  • @davekimball3610
    @davekimball3610 6 років тому +16

    Oh happy day, another video from Mr Carlson!

  • @denniscook1422
    @denniscook1422 4 роки тому +2

    Many years ago I collected antique radios. At one point I had 150 of them. I sold them just before the bottom dropped out of the market for them. The proceeds bought us a house. I repaired many of those radios with no more training than a couple of small books. I enjoyed the hobby very much. I enjoyed your video a lot. Wish it had been around in the mid 80s. I never got zapped from a radio. But did with antique telephones.

  • @GMan-Howick
    @GMan-Howick 4 роки тому

    I have no idea what I have just watched but I am impressed.

  • @erbro
    @erbro 6 років тому +7

    This is exactly the love for electronics I was taught. 50 years ago Lol

  • @abc-ni9uw
    @abc-ni9uw 6 років тому +20

    I get home from a long boring hard days work to find out my good friend Paul has uploaded a video.
    No matter What it is.
    I put my headphones on and that's my night improved :)
    Thanks Paul but i seriously want you to restore my pioneer sa-9800 dual mono block stereo amplifier.

    • @Foozlebop
      @Foozlebop 6 років тому +2

      The power amp and power supply of the 8800 is a piece of cake. Tone section and preamp not so much. I imagine the 9800 has a similar layout. Also the 8800 had a noisy diff pair.

    • @abc-ni9uw
      @abc-ni9uw 6 років тому +1

      @@FoozlebopI want a total over haul

  • @billville111
    @billville111 4 роки тому

    Antique radio restoration from the space station. Only on UA-cam. Fantastic!

  • @blackpoolbarmpot
    @blackpoolbarmpot 6 років тому +1

    I stayed 'glued' to this Video and got (probably) as much of a thrill out of seeing this lovely Radio properly restored, as 'Mr Carson' did. I know from personal experience that it is very gratifying to get a Radio (or any other piece of electrical or electronic equipment) working so well, after many hours of work put into restoration. I have a 1936 Radiogram and a 1934 Radio - all fully restored by me, in my 'Lounge'. (I still have loads of Shellac 78 rpm records to play on the 'radiogram') !

  • @frankpitochelli6786
    @frankpitochelli6786 5 років тому +7

    Paul, why are you not teaching or passing your extensive knowledge to these newer generations, I've been in the electronics service for 40 yrs, and you are an absolute crackerjack (as we would say back in my day)......
    You have a perfect demeanor and skill of projecting knowledge.
    Great video as usual.
    I would've loved to have met you when I was in my hayday in the TV and appliance service business....
    Man, I could've picked your brain something fierce...😀..!

    • @BruceNitroxpro
      @BruceNitroxpro 5 років тому +2

      Frankie Pitochelli, Ah, but he IS teaching the NEW restorers right here, right now. And doing a heck of a good job at it.

    • @elvisburgerking8675
      @elvisburgerking8675 5 років тому

      @@BruceNitroxpro the new gen. mainly doomed has attention span of closer to 2 minutes rather than the required 2 hours

  • @stuthomson
    @stuthomson 6 років тому +4

    Your BEST radio restoration vid yet. Really enjoyed it. Perhaps you could restore an old TV?

    • @BobPegram
      @BobPegram 6 років тому

      Give the young 'uns a chance to see real B&W TV! "No, there's no way to see it in color, not even on the packed up color TV in the attic!" "These programs (from You Tube) were made in black and white!" Later on, you get to tell them: "On this TV, even color programs come out black and white."

    • @edwardbyard6540
      @edwardbyard6540 5 років тому

      Bob Pegram Believe it or not, here in the UK, some people still have B&W TVs. As you need a licence for your TV by law (big fine and possible jail time if you don’t have one!) black and white TVs are used by the blind or partially sighted. A B&W licence is half the cost of a colour licence. There are about 3000 B&W licence holders left. Crazy but true!

  • @MovieVigilante
    @MovieVigilante 4 роки тому

    It seems appropriate that someone named Mr. Carlson would be restoring an old radio. Nice work, Big Guy. You didn't even need Johnny Fever or Venus Flytrap to help you out.

  • @nicholasperrin1097
    @nicholasperrin1097 2 роки тому

    Had flash backs to my time in the Navy when you showed which resistors you decided to use as replacements and then again when you whipped out that Tektronics scope. Transported me almost 2 decades back to my shop on the ship.

  • @royelectrotechnic8711
    @royelectrotechnic8711 6 років тому +6

    It's really fantastic radio restoration 👍👍I really enjoyed and I learned more technic in this video, great job.
    You Know sir Paul I love your channel it's because of lots of real information, and your line of thinking and thought is absolutely great. More of inspiration, incouragement, and I have found only here how to read a bad resistor that I never knew before. Not all bad resistor is faulty Lol.
    Thank you so much mr Paul for this restoration and the radio now back to its own case and good as brand new, you did well.

  • @ao2528
    @ao2528 5 років тому +3

    Your restoration style is exceptional, I lost my interest to watch others for very clear and many reasons, so perfect at any level, no one even can come close to, countless thanks for your excellent informative works.

  • @KLCKLC-vi6fd
    @KLCKLC-vi6fd 2 роки тому +1

    You're off to the races with this one The Bell Mount track that's for sure a nice looker man! Great buy, Mr. Carlson!

  • @heisrisen6898
    @heisrisen6898 Рік тому

    These videos just bring back memories as to when I was a kid opening tvs 📺 & radio receivers 📻 I remember they had a unique old vintage smell to them man time has gone by. About to reach my forty’s 😳

  • @psionl0
    @psionl0 6 років тому +3

    Cool! Vintage Mr Carlson. I love watching videos like this.

  • @heru-deshet359
    @heru-deshet359 6 років тому +8

    Beautiful. There is a m agical feeling to me about working on vintage radios and listening to them after. Like working with a time machine.

  • @FelicianaDelacruz
    @FelicianaDelacruz 3 роки тому

    It's a real testament not only to Mr. Carlson's repair and restoration, but also to the designers, manufacturer that this radio was so well designed and built. Everyone once in awhile UA-cam's suggestions are right on the money and this channel is really a gem. Thank you for sharing your knowledge and advice to the the electronics and restoration community. Keep the great videos coming, they are really enjoyable and informative.

  • @chriscimino7854
    @chriscimino7854 2 роки тому

    I am impressed how good you are with your hands and it takes a lot to get me impressed. I've been working as a TV repairman for 35 years and I got really good at what I like doing and I would not have attempted to remove the dial paper I probably would have damaged it but I can say you're the better man. Thumbs up👍

  • @Stuartrusty
    @Stuartrusty 6 років тому +22

    As always, a beautifully well restored piece. Invaluable experience and knowledge brought to great use.
    Thank you for making these restoration videos, and I hope you will enjoy listening to Christmas Carols on this fine machine.

    • @djhaloeight
      @djhaloeight 6 років тому +3

      Stuart Russell That’s the best thing to listen to on one of these old beauties.

  • @user-mc5mu1xl4w
    @user-mc5mu1xl4w 5 років тому +3

    Ooooh. It looks like hell from the inside. A hell for electronics restorators
    Man, you did a great job!

  • @SPEXWISE
    @SPEXWISE 6 років тому

    This was a great video especially because you filmed it from the ISS.

  • @jimrick6632
    @jimrick6632 6 років тому +1

    YOU ARE THE MAN...YOU MAKE WHAT COULD HAVE BEEN A DULL BLOG, A REALLY INTERESTING RESTORATION..KEEP UP THE GREAT WORK......

  • @paladin0654
    @paladin0654 6 років тому +23

    Marvelous video. You're lost in time sir. I have a 1936 Zenith console that I got from my folks. Hitler, Churchill and Roosevelt have come through that thing.

    • @BruceNitroxpro
      @BruceNitroxpro 5 років тому +1

      Paladin 06, I like the way you think! Nicely said.

    • @Charlie_Crown
      @Charlie_Crown 5 років тому

      @@BruceNitroxpro Also thinking the same thing, all the history that passed through it 👌

  • @RobertSnyder100
    @RobertSnyder100 4 роки тому +1

    WOW....What a great teacher you are. I learn a little ...and maybe remember...more....each time I watch another Mr Carlson video. I likely will not be restoring vintage radio...but Ihave a few old tube units...and ...I get it....I understand...on a odd emotional level....the attraction to the old warm glow of the Tube...I am very much appreciative of your willingness to share your knowledge and passion.....PLEASE CONTINUE !

  • @obnox7601
    @obnox7601 6 років тому

    Awesome video, thank you! I used to listen to "The Shadow Knows" as a kid on radios like this. Next time I see an old radio in an antique shop I'll buy it! And I'll not fear trying to restore it!

  • @ridakr9473
    @ridakr9473 6 років тому +7

    Thank you mr carlson for this video of restorstion ,you are really a really electronic info treasure ,i am following you from algeria and your chanel very useful and cool thank you for your professional work and explanes

    • @MrCarlsonsLab
      @MrCarlsonsLab  6 років тому +1

      Thank you for your kind comment Rida!

  • @glenngoodale1709
    @glenngoodale1709 6 років тому +9

    I look forward to watching each and everyone of your video's!!! Makes my day

  • @skycarl
    @skycarl 6 років тому

    Great restore Paul,,,,,, What a nice radio as it rises from the dust..

  • @andrewpike2924
    @andrewpike2924 6 років тому

    I watched this video from start to finish, what an enjoyment it was. You did an excellent job of cleaning the chassis and you new wiring was very neat and tidy. After the alignment it worked really well, as you said "just like it came out of the factory". I was however somewhat disappointed that you did not remove the guts from the old paper capacitors and re-stuffed them with the new capacitors. It just seemed to be a really good thing to do as you put so much effort into the restoration.
    Putting that aside, you are really an expert and you deserve credit for your very good and informative videos. Keep up the good work Paul.

  • @jacksat2252
    @jacksat2252 6 років тому +84

    Woho !!! Full movie lenght. Nice.

    • @electron-1979
      @electron-1979 6 років тому +3

      Awesome! Much better than the live streams other UA-camrs are doing!

    • @BobPegram
      @BobPegram 6 років тому +4

      They (You Tube people) say that 20-30 minute videos are the best to catch and hold an audience. Have they never paused watching a Mr. Carlson video to finish it a day or two later?

    • @BobPegram
      @BobPegram 6 років тому +3

      Mr Carlson, you are one of the people helping me to finally learn things that I dimly remember from college and things I was never taught (tubes and their circuits).

    • @electron-1979
      @electron-1979 6 років тому +1

      I had no choice, but to do so!

    • @woodywoodlstein9519
      @woodywoodlstein9519 5 років тому +1

      It’s so great. When others would be long done , because they don’t have much to say. Paul packs it all in giving full respect to his viewers / his customers , and the machine itself.

  • @billmoran3812
    @billmoran3812 6 років тому +3

    Beautiful radio! I need to work through my stock of radios to be restored this winter.

    • @BruceNitroxpro
      @BruceNitroxpro 5 років тому

      Bill Moran, Hope you make "Carlson quality" restorations and POST YOUR VIDEOS on Patreon, too!

  • @nickblackburn1903
    @nickblackburn1903 6 років тому

    Doh, I just got rid (sold) of my British 1950's bakelite valve radio as I didnt know how to fix it and now you post a video with a very similar radio....ah well. great video as always. Thanks :)

  • @jamesjacocks6221
    @jamesjacocks6221 4 роки тому

    It's a great escape to see Mr. Carlson bring back a classic radio but the real therapy is in the monologue: his Canadian pronunciation is refreshing to these jaded American ears. My. mom used to voice her L's so distinctly that I would shudder as a child hoping not to be taken as foreign. Of course that was useless and the foreign property was a feature of the mind.

  • @Bass.Player
    @Bass.Player 6 років тому +39

    When I was a kid in the 50's I got shocked all the time by everything, no one thought anything about it, it was normal.
    I love these old radios especially the old wood ones. K5AZE...
    ▄▀▄▀▄▀▄▀▄▀▄▀█▓▒░A░W░E░S░O░M░E░░▒▓█▀▄▀▄▀▄▀▄▀▄▀▄

    • @1959Berre
      @1959Berre 6 років тому +8

      I guess I must have been about 14 or 15 years old when I 'disassembled' a vintage Grundig on tubes back in the early seventies. I had no clue I was dealing with high voltage. I still don't understand how I was not fried while poking around in that unit.

    • @tailsdollblack9340
      @tailsdollblack9340 6 років тому +3

      been there. got the shock of my life testing wires on radios such as my radio project i mentioned above . i thought the speaker was 12 volts not 60! XD no need for coffee that day. already had a buzz

    • @jagardina
      @jagardina 6 років тому +2

      One summer we set up the garage as a den (there was no air con and it was cooler). There was an area rug but if you weren't standing on the rug you would get a pretty stout tingle when changing the channel on the TV. I measured 90 volts AC. We were teens back in the early 70s and loved giving a jolt to unsuspecting friends by standing on the concrete and touching them while they changed the channel. Really stupid in retrospect.
      I did electronics and should have known better.

    • @Geopholus
      @Geopholus 6 років тому +3

      Unfortunately for Keith Relf of the Yardbirds it wasn't normal, it was the end of his life , when touching a microphone that was cross grounded (through a PA) with his guitar (amp), and I believe it was through electronic equipment that was transformer isolated but had "hum balancing" switchable through a capacitor (a capacitor connected to one side or the other of the AC line coming in.). That is why they are called "death caps". Although I believe this was in the UK, with 220 V 'mains', AC supply,.. the charge carried by a .01 cap (due to its reactance at 50 Hz is as miniscule part of the duty cycle. RESPONSIBLE TECH'S PLEASE REMOVE DEATH CAPS !!!! I've been doing repairs for 50 years , and shocked many times near the beginning of my career, actually had no shocks for about 25 years straight however,... please always check the unit being serviced is unplugged , and main filter caps are discharged before servicing. I nailed myself a few months ago because "I thought I unplugged that".... thinking isn't the same as doing,... and Tesla's one hand rule is excellent!

    • @Bass.Player
      @Bass.Player 6 років тому +4

      Almost as bad as getting a mustache hair stuck in the microphone grill and when you jerk back the mic comes out of the stand and hangs by your lip, this activity will even make King Kong's eyes water!

  • @5cloudwalker
    @5cloudwalker 5 років тому +4

    I randomly came upon this...what a treat, you have opened up a whole new universe with your expertise...your words and knowledge are quite beyond me but I can appreciate what you are doing and with each episode my understanding of electronics opens up a little each time...its both intimidating and satisfying to watch a teal master at work. bravo

  • @jamesketchum5047
    @jamesketchum5047 4 роки тому

    it always hurts me to see old tech like this in rough shape but then Mr C brings it back to life and gives it another chance at life, ive always been fascinated by tech of the 30's through the 70's. tube tech is so fascinating to me

  • @redstrat1234
    @redstrat1234 5 років тому +1

    I know nothing about electronics but what you do is fascinating

  • @robyoung9463
    @robyoung9463 6 років тому +4

    incredible Craftspersonship the DUAL LAMPS Outstanding : )

  • @NebukedNezzer
    @NebukedNezzer 6 років тому +3

    nice radio restoration.

  • @jameshorn7830
    @jameshorn7830 5 років тому +1

    Mr. Carlson, sir, you have a wonderful style, and a soothing, reassuring voice. It's very obvious you know what you're doing...

  • @John_Smith__
    @John_Smith__ 6 років тому

    Nice!!! Very nice! a classic Radio ! thanks for the video!

  • @MuhammadAmin-th4bp
    @MuhammadAmin-th4bp 6 років тому +3

    Hi Sir ! I watched your all kind of video , your explanation method is excellent .I love to watch videos.I'm an Electrical student . I request for if you have time . to explain ON Grid,Off Grid system these two type of supply , hope

  • @TheRadioShop
    @TheRadioShop 6 років тому +8

    Hmm, what to do. Repair a HP 8656B or what Mr Carlson's Lab......Decisions.....Well I watched a 2 hour Excellent video. Well done Paul. Just a fantastic radio and now as good if not better than a new one.

    • @MrCarlsonsLab
      @MrCarlsonsLab  6 років тому +1

      Thanks for stopping by Buddy! That 8656B sound like a great project too. Nice signal gen.

    • @PelDaddy
      @PelDaddy 5 років тому

      Buddy, you will love that 8656B. I have an 8657B. You can even do "sweep" FM alignments if you use external FM DC modulation with a sawtooth wave. Looking forward to a video on that.

  • @kevinfromsa1434
    @kevinfromsa1434 5 років тому +1

    Brilliant Paul. Thanks so much for taking the time and effort to restore this radio. You are part of a dying (or dead) breed!

    • @MrCarlsonsLab
      @MrCarlsonsLab  5 років тому +1

      Thanks Kevin. Yes.. not many of us around anymore.

  • @eugenetheodore2956
    @eugenetheodore2956 3 роки тому +1

    Hello Paul, I just finished restoring my Belmont 636B following your great video. You are truly a master! Thank you so much for your great videos.