Install a Keyless Entry System in a Honda ODYSSEY or any car w/ central lock in less than 20 minute

Install a Keyless Entry System in a Honda ODYSSEY
Install a Keyless Entry System in any car with existing central lock system
In this video, it will how to check if the car is a negative trigger central lock, how to find the wire in the harness and how to install the basic locking function of a keyless entry system in less than 20 min.
Enjoy😊

[@ayrimemishev718]

I've watched a dozen of these videos in English and I didn't understand a thing and then I finally i run into this video and don't understand a word you said, but just learned everything I need to know to do this on my own step by step. Well done and thank you so much! God bless you too! :)

[@PinoyBuysAndDIYs]

You're welcome Sir. 😊, sorry next time I'll try to do it in english or put a subtitle😁. Hope this help anyway😊. Hope you'll subscribe to this channel. Thank you.😊🙏

[@ayrimemishev718]

@@PinoyBuysAndDIYs It did help ALOT. Thanks again! :)

[@ayrimemishev718]

@@PinoyBuysAndDIYs I did everything you explained and it worked :) I'm super greatful. Just one thing: when i lick to lock button, the relay clicks but it wouldn't lock the the door. Unlock works properly. Any ideas ? The cars is 2000, Mitsubishi Galant 2.5 V6 sedan. I asked in our local mitsubishi forum but no luck there, so any help would be greatly appreciated !

[@PinoyBuysAndDIYs]

@@ayrimemishev718 Does it works when you directly supply the "lock line" of you car with negative signal?

[@ayrimemishev718]

@@PinoyBuysAndDIYs No it doesn’t. It only works when I get the orange wires involved, but I’m afraid it can become a problem after sometime e.g short circuit or burn the cables or something. It looks so easy when you do it

[@kabsky61]

sa dami-dami ng videos napanood ko tungkol sa keyless entry ang video mo lang ang malinaw at well explain at hindi masalamuot intindihin,salamat kaibigan at sana marami kpa DIY na gagawin sa susunod i salute u bro thanks again.

[@PinoyBuysAndDIYs]

Salamat po. :) Godbless.

[@mariocandelaria7273]

Maganda at malinaw ang inyong video about keyless entry napanood ko po yong complete video ninyo. And itong video na short lang ang connection mas nag karoon ako ng kaalaman. Thank Sir! Sana meron po kau sa Hundai eon. 🙏👏👏👏

[@PinoyBuysAndDIYs]

Thanks po sa panunuod. Same lng din nmn po ng concept yan pag universal.. goodluck sa diy nyo po

[@huytranquoc7756]

good

[@littlegrayhaven8797]

sir pwede ko din po ba itap ung positive ng keyless module sa positive ng module ng central lock? thanks po

[@Hataku08]

Salamat sa video tutorial na to sir, hindi ko kase mahanap ung negative trigger ng vios gen 4.5. Salamat ulit

[@Hataku08]

Sir tanong ko lang po, sa video na po to nagtap po kayo ng test light sa positive para mahanap negative trigger, ung isang video po ninyo sa negative naman po kayo nagtap ng test light at sundot sundot sa negative trigger? Salamat po same lang po ba un?

[@harold1212121]

​@@Hataku08nag tap sya positive sir para maconfirm na negetive trigger talaga ung lock. If di umilaw ung tester habang sinusundot mo ung switch ng lock tapos sa positive ka naka tap. Malamang positive trigger un. Baliktarin mo lang

[@judithbantilanral4081]

sir ask k lang pano po namn kung hind n talaga gomagana yong original nyang module?. sana masagot m ako agad. salamat po.

[@renzmarcobautista2591]

how much po labor nyo if mag papakabit ng keyless entry??

[@jaysoclarkjison8329]

ung indicator light q na blue paps hindi nag biblink steady lng xa naka light after q ma lock 3mins. nag aalarm xa kusa ano po problema? salamat po sa sagot..

[@eelhase]

Big Thumbs Up for an excellent video! In your case, both lock/unlock triggers are negative, that's why yellow and yellow/black are connected to negative, right? Probably if both triggers are positive, yellow and yello/black wires would go to positive. What if both triggers come out negative and positive alternately, which means while both triggers are being negative, when lock is on(+), unlock still remains negative, and vice versa? Hope for getting your response. Many thanks!!!

[@PinoyBuysAndDIYs]

"Probably if both triggers are positive, yellow and yello/black wires would go to positive. " - yes
"What if both triggers come out negative and positive alternately" - there is also a configuration for this, but a different application. This is usually used to control the actuator directly,(not the central lock triggers), check the video link below where I demonstrated this scenario. Hopefully your question will be answered.
ua-cam.com/video/JNrwV29YOGM/v-deo.html

[@motojam2963]

Sir same brand tyo may concern lang ako sa alarm ko.. bigla syang mag hazard light while tumatakbo ako kahit maayos naman pagsira sa door switch .. minsan nawawala na yong hazard light mayat² mag oon ulit sya. Kahit naka off naman itong hazard switch ko.

[@phutran5698]

Hi did you wire up to door lock trigger wires?why it work?I did wire up to door trigger but not work,I have to find separate wire lock and unclock and it work so can’t to install door trigger,hope to read mine

[@PinoyBuysAndDIYs]

Yes, i the triggers to the door lock switch. It should work as long as the switch working, meaning it has a connection to the central lock.

[@shantadarren6450]

Thanks for the video, ang simple lang palang magkalagay ng keyless entry. Ganyan po ba lahat ng nabibili online?

[@PinoyBuysAndDIYs]

Mostly same lng.. lalo na ung para sa connection sa central lock, pag may additional feature nlng ung module dun nagbabago. pero as long as naiintindihan ung diagram.. madali na syang sundan. :)

[@elrickjohnocliaman4398]

Ayaw gumana ng lock/unlock switch sa driver side dol .pero gumagana ang remote.. normal lng vah yun .. bagong kabit yung keyless..

[@JayGamzTV]

Good Day sir maganda buhay
Sir tanong ko lang po after 3 years of using this Keyless remote Car, kamusta na po at working properly parin ba hanggang ngayun?

[@PinoyBuysAndDIYs]

Sorry sir, Hindi ko masasagot sir since nagpalit ako ng sasakyan last year.. pero the year na gamit ko hindi nmn nagkaroon ng issue.

[@reginaldevangelista5255]

Pno pag stall s trank ng kotse

[@kentv3996]

boss pag masira ba ang module pwede lang palitan parang plug and play kahit anong keyless entry?

[@PinoyBuysAndDIYs]

Hindi sir. Dapat same sila ng model.

[@whiteycobray9261]

Hi sir ..bakit po ayaw gumana ng trunk swicth ung color blue wire..CRV gen 2 po..

[@PinoyBuysAndDIYs]

Check nyo muna po kung nagbabato ng power pag pinipindot sa remote. Btw. Long press po un usually. Pag wala po, defective ung module..

[@davozzvlog]

Lods pwede ba syang gawin sa mistsubishi sedan? Kc my central lock ndin sya, sabi skin kc ng mekaniko need pdaw ng actuator. Sana masagot ang tanong q salamat and more videos to come.

[@PinoyBuysAndDIYs]

Basta po, may central lock na, tapos lahat ng doors naccontrol using lock/unlock button(electronic), no need for additional actuator. Pero ung ung main door.naccontrol lng using physical key, or stick, or lever, meaning hindi electronic button. Posible na wala pa po un actuator. So, ung driver door need pa po lagyan.

[@davozzvlog]

Until now pinapanood q pdin itong video mo lods, dq prin magets kc sa honda jazz ang sample, dq alam qng pano sya ikakabit sa lancer. Paturo nman lods.

[@PinoyBuysAndDIYs]

@@davozzvlog try mk panuorin sir ung video about sa.keyless entry. Dun pag nagets nyo po un alam nyo na gagawin. Check nyo po sa videos ko. "Paano gawing Keyless entry ang sasakyan mo" ung title.

[@oncdbc01]

paano mag add ng additional remote sa module?

[@PinoyBuysAndDIYs]

Hindi ko pa po na-try, pero dun sa instruction: press and hold lng ung button dun sa likod ng module until mag-flash ung signal light, then press any button sa remote.
Pwedeng ibang way sa ibang brand, pero usually nasa instruction naman po. un.🙂

[@averomotovlog1470]

sir pwede ba to sa akin, may existing keyless entry na kasi sa akin gforce ang brand pero wala remote nung nabili ko ung sasakyan. pwede ko ba tangalin lang yung module nya di nayung mga wire kasi nakakalito, tapos ito lang susundin ko? di ba magkakaproblema?

[@PinoyBuysAndDIYs]

Yes po, pwede un.. basta makita nyo lang po ung mga triggers(lock/unlock). Ang suggestion ko po. Nahapin nyo muna po ung lock/unlock triggers, pag nakita nyo po, tanggalin nyo ing module. Tapos itest nyo muna po ulit kung gumagana pa ung mga triggers, then iconnect nyo na po ung bagong keyless system.

[@averomotovlog1470]

okay po sir. ngayun ko lang kasi sya napansin na meron pala sya keyless entry at tinignan ko mga actuator, yung sa driver side lima ung wire nya. tapos pag inilock ko nag lolock lahat nang pinto, pati pag nkatakbo na tapakan ko brake automatic lock din lahat. yun nahanap ko ung pinaka keyless entry nya na module.

[@PinoyBuysAndDIYs]

@@averomotovlog1470 i see. So gumagana pa ng maayos ung keyless entry system nya. Actually sir. Mas maganda para hindi mawala ung feature na sinsabi mo pag inapakan ung brake ng llock, wag mo ng tanggalin ung exisitng module.. itap mo lng ung bagong module dun sa lock unlock trigger. Katulad ng ginawa ko jan sa video. Mas mabilis pa ung installation mo pag ganun. Bale ang additional feature lng nun is nagka remote sya.

[@averomotovlog1470]

ahh okay sir, so bali dalawa na sila module pag mag tap ako bago? sayang kasi walang remote nang pagkabili ko sa sasakyan. may siren din sya sa may engine bay naka linya pa. kaso di magamit walang remote 😅

[@PinoyBuysAndDIYs]

@@averomotovlog1470 yes sir. Pwede naman un sir. Wala naman conflict since wala na ung remote ng isa.. pwede rin sir. Icheck nyo sa likod ng module nung existing keyless entry system kung may learn button. Pwede kcng mag learn ng bagong remote ing ibang keyless entry system. Pra un nlng ung gamitin mo sir

[@arthurliboon6881]

Sir gd am po,,,may dati ng keyless entry ang car ko,,nasira lng ang remote,,pwede po ba na remote lng ang bibilhin ko,,tnx po sir God speed po

[@PinoyBuysAndDIYs]

Kung universal keyless system po ung existing, check nyo po sir kung meron button sa likod ng module ng keyless entry, ung mga universal po kc usually my Learn button incase gusto mong mGdagdAg or magpalit ng remote.
Pag original/stock po ung keyless nyo. Magdedepende na po un sa manufacturer and model ng sasakyan nyo kung pwede magpalit ng remote.

[@arthurliboon6881]

@@PinoyBuysAndDIYs ,,oki po Sir,,i tsek ko po,,yung front passenger door di po ma control sa central lock switch sa driver side door,,ang 3 door po oki nman,,tnx po Sir,,God Speed

[@PinoyBuysAndDIYs]

@@arthurliboon6881 ah baka need nyo lng po nyan magpalit ng actuator dun sa door na hindi macontrol.

[@arthurliboon6881]

@@PinoyBuysAndDIYs ,,oki po Sir,,,maraming salamat po,,,

[@jedaleahjedsteelworks4794]

Sir tanung ko lang po. . . Positive/negative triger po yung alarm ko. Panu po ako mag lalagay ng switch po pqra sa central lock. . .

[@PinoyBuysAndDIYs]

Kung ano ing need nyang signal pra ma trigger ung lock/unlock sir. Gamitn kng tester. Then pag tina-toggle mo ung central lock check mo kung anonh signal ung binibigay nya..
Bale meron ka namg central lock gusto mo lng lagyan ng switch, tama boss? Ung central lock mo ba is original ng car or universal?

[@jedaleahjedsteelworks4794]

@@PinoyBuysAndDIYs universal sir na central lock sir. Bali ang ginawa ko ay positive/negative triger. . .

[@PinoyBuysAndDIYs]

@@jedaleahjedsteelworks4794 gumagana na ung alarm mo boss? Not sure pag ganyang setup. Kc pag switch isang signal type lng ung ipapasa nun.. baka may negative trigger parin ung central lock mo boss..isang module lng ba for alarm and central lock?

[@jedaleahjedsteelworks4794]

@@PinoyBuysAndDIYs dalawang module po sir ginamit ko. Magkahiwalay po module ng central lock at alarm po. . .

[@jedaleahjedsteelworks4794]

Bali sir ok napo. . . Pjnagana ko lahat ng module box po nya. . . Module ng central lock at module ng alarm pinagana ko. . . Sa central lock no problem naman po sinunod ko manual sa central lock. Yung sa alarm naman sinunod ko diagram manual ng positive/negative trigger. . . Ok napo sya sir nakapag lagay narin po ako ng manual switch ng hindi binabago po yung wiring installation ko na positive/negative trigger. . . Na ipost ko sir sa isang yt account ko video. Pwede nyo po sya watch den kayo po mag paliwanag po. Kasi mas malinaw po kayo mag paliwanag sa akin. Hehhehe first time kk kasi ginawa mag video. . . Ma gets naman po agad yung ginawa ko sa manual switch kjng anung wire po mga ikinabit ko doon. Kaya mas mahanda sir maipaliwanag nyo din po ng maayos po. . . Kasi mas malinaw po kayo mag paliwanag kesa sa akin. Hehehe

[@romnilroberts8834]

Pwde po pashare wer nyo nabili keyless. hm po?

[@PinoyBuysAndDIYs]

shopee.ph/product/277028386/7840182527 eto po :)

[@romnilroberts8834]

@@PinoyBuysAndDIYs tnx!

[@jaysoclarkjison8329]

paps, tanong kulang bakit hindi sumasabay lahat ng actuator ko pag e open ko sa driverside door ko? pero pag open ko gamit ang remote sabay sila lahat mg open at lock ano po problema? salamat po sa sagt...

[@PinoyBuysAndDIYs]

Ano pong ibig nyong sabihin pag open nyo driverside? Pag unlock po ibig nyong sabibn? If yes, anong gamit nyo po? Button or ung lock stick?

[@jaysoclarkjison8329]

@@PinoyBuysAndDIYs ung central lock q paps pag remote ung gamit q pg open sabay sila mg bukas at sirado pero pg inopen ko ng manual sa driverside hindi xa sabay mag open un lng sa driverside q lng nag oopen

[@PinoyBuysAndDIYs]

@@jaysoclarkjison8329 eto po ung pwedeng reasons:
1. Walang switch na nakaconnect sa manual lock
2. Need palitan ung main door nung 5-wire actuator(baka wala or sira na) link mo sa manual lock pra magsend sya ng signal sa central lock.
eto po..check nyo kung pano gumagana ung central lock with main door actuator ua-cam.com/video/AqFoezq0-Z0/v-deo.html

[@jaysoclarkjison8329]

@@PinoyBuysAndDIYs napanood kuna yan paps.. ung isang problema q paps bakit di nag biblink ung led indicator na blue pg nag lock aq ng door? steady lng ligth nya paps tpos 15seconds nag aalarm xa..

[@PinoyBuysAndDIYs]

@@jaysoclarkjison8329 ah yan d ko pa na experience sir. I'm assuming keyless entry+alarm ung system mo?.. baka hindi naka tap ng maayos ung door or ignition switch wiring, kaya nag trigger ung alarm..

[@reymundnacino7773]

sir patulong naman.. nag kabit kc ako ng alarm.. ok pa naman nong pag kabit ko tinesting ko ok naman.. kinabukasan ginamit kk sasakyan.. habang tumatakbo bigla naglock tapos nag alarm.. nong unlock mga ten seconds nag lock naman sabay alarm.. kahit tumatakbo sasakyan

[@PinoyBuysAndDIYs]

Hindi ko sure sir, baka defective ung mismong module sir.. nag gaganun lanh ba pag tumatakbo ung sasakyan? Kung umaandar engine pero naka park lang hindi nangyayari?

[@reymundnacino7773]

@@PinoyBuysAndDIYs kc nong ginamit ko sir ok pa naman xa.. nong nag park na ako.. tpos nong uwi na ako e unlock ko..nong tumatakbo na mga 100meters.. yun biglang nag lock sabay alarm na..

[@PinoyBuysAndDIYs]

Hmmm so ngayoj sir everytime na gagamitin mo nag aalarm? Ung mga doors mo ba nag iinidicate kapag nagbubukas ka ng pinto? May logic kc ung mga alam kaparang nag unlock ka tapos hindi nya nadetect na nagbukas ka ng pinto magllock ulit un. So baka un. And ung sa ignition.. nakaconnect sir?

[@reymundnacino7773]

@@PinoyBuysAndDIYs oo sir nag aalarm parin.. ang kinabit ko lang sir.. positive,ground,alarm,tpos papuntang central lock na.. yong iba di kuna kinabit.. kc hilander sakin wala connection sa pinto.. ang wire na papuntang ignition di kuna kinabit..

[@PinoyBuysAndDIYs]

@@reymundnacino7773 try mong lagyan ng power ung para sa pinto sir. Kung anong nasa diagram.. kung negative ung nakalagay try mo itap diretso sa negative na live. Try mo lng.. baka magwork.

[@thoremberda3628]

Gd day sir, patulong sana ako,nag i install ksi ako ngaun ng keyless entry system at sinusunod ko yng video nato at 1st time ko po mag diy ng electrical d2 sa vios gen2 2012 batman type ko, naikabit or naiconnect ko na po yng keyless entry module ang problema gumagana na sya, pero yng 2 wires na kulay brown from keyless module yng para sa signal light, tuwing i coconnect ko sya pumuputok yng fuse na 15 amp nong positive wire from keyless module, paano kaya to sir,kailangan ko po bang taasan yng amp noon, mga ilang amp kaya puede. Salamat and God bless sir.

[@PinoyBuysAndDIYs]

Check mo muna aa tester sir kung working ung mga brown wire and kung anong binabato nilang signal. Baka sa maling wire sya naka tap. 15Amp mataas na un dapat hindi pumutok kung signal lights lang..

[@thoremberda3628]

Ok sir, maraming salamat. God bless

[@mr.jmiranda4198]

O boss kapampangan ka?😊

[@PinoyBuysAndDIYs]

Wa boss😄

[@mr.jmiranda4198]

Salese na! Boss mag upload nkng dakal videos suportan daka😊 madagul lang bage deng ggwan mu iwas gastus. Balu mu nmn keng talyer o kasa atnala kamal manyingil aha

[@PinoyBuysAndDIYs]

@@mr.jmiranda4198 wapen boss istu ka. Hehe wa boss potang ating oras gawa ku ulit. Salamat keng suporta boss.

[@lester4752]

Paps..pano malaman kung negative trigger or positive trigger or positive-negative trigger po yung central lock

[@jedaleahjedsteelworks4794]

Sa manual po ng alarm sir may wiring diagram po. Doon nyo po malalaman sir kung ang pag install ng wiring sa unit alarm ninyo ay postive trigger ba or negative trigger or both positivenegative triger sya.