Hello. Good vídeo, thanks for your explanation. I have a doubt, when you calibrate the current you used a short circuit instead of use a resistance, this will not brake the step down power supply?
No dear that module is designed in such a way taht you can set the maximum current limit and that can only be set by short circuit and its has the protection mechanism so no worry when you apply resistance and cm set the current then it's wrong hope you understand
Good Morning! I just watched your video and found it very interesting... I have the following doubt: the zb2l3 I bought, when I test it with the 1amp discharge configuration, is not reporting correct values... For example, a cell that I removed of the notebook used, it has a capacity of 2200mah and when I'm going to test it on the zb2l3, it says it has 3,475mha. is this correct? OR my device is out of calibration.?? Cell Model: LG LGDAS31865. And when I put two cells together to make a pack, it only carries a 3,000ma cell phone.
Hey Rogerio_88 , I al testing a lot of cells today, and I also got a lot of big numbers, such as 3000+ but I also got smaller one, like 1367, 1682 ... and I don't know if it is correct or not, did you come up with any answer to your question?
Sir,... I've followed ur instruction.. it give the best accurate on voltage, but not with the current, now my module show the wrong current, and i can't make it better, can u tell me how to fix it? Or my module is broken? thanks for your regard
Calibrate it once again with the same method but make sure the current controlled module should be accurately set to the said current then the ZB2L3 will be calibrated accurately
After carrying out this procedure, my module only shows error 5, is there a way to restore the factory configuration, or do I have to buy another module and not touch it again. ?
Video is so accurate! But: Autor cannot show (it's missing) real adjusting of current during calibration prosess - as the voltage adjusting. And Please - Include english text on most important points of video.
yes you can no need to adjust it only draws current from cell through resistance and measure its capacity this can. measure voltage upto 12v so Lipo batteries voltage are far less then 12v use it without any hesitation
Assalam walekum Bhai ye tester 15 volt 3 amp ka cell support karta hai lifpo cell 6 ampere ka hota hai to 3 ampere se jyada ka cell ko support kare ga kya
Dear yeh tester Hai jis nay cell ko test karm Hai ap jo resistance add Karin itna current draw Kar k testing Kar day ga Pher yeh keh skaty hain k ap nay yeh cell 1 amp ya 2 amp discharge current pay test kia Hai Or kitny mAh yeh count Kar skata Hai wo 9999mAh hain Volatge yeh 12v tak support karta Hai means 6 volt ka cell test ho jaiy ga
The first calibration step after entering the calibration displays the 0u0A; short connect both positive and negative input terminal and press the "OK" button Next, the display will show J10u; apply 10.00V DC between the input positive and negative terminal and press the "OK" button again. The display will show J2.0A; apply 2.0 A DC current between the input terminals and press the "OK" button to complete the calibration.
Is this xl4015 buck module?
Excellent and perfect process.
Hello.
Good vídeo, thanks for your explanation. I have a doubt, when you calibrate the current you used a short circuit instead of use a resistance, this will not brake the step down power supply?
No dear that module is designed in such a way taht you can set the maximum current limit and that can only be set by short circuit and its has the protection mechanism so no worry when you apply resistance and cm set the current then it's wrong hope you understand
@@RizwanSaeed ah, ok, that I dind't know. I ordered mine and now I can be calm. Thank you very much
Rizwan Saeed You are the Great
Very Nice
Good Morning! I just watched your video and found it very interesting... I have the following doubt: the zb2l3 I bought, when I test it with the 1amp discharge configuration, is not reporting correct values... For example, a cell that I removed of the notebook used, it has a capacity of 2200mah and when I'm going to test it on the zb2l3, it says it has 3,475mha. is this correct? OR my device is out of calibration.?? Cell Model: LG LGDAS31865. And when I put two cells together to make a pack, it only carries a 3,000ma cell phone.
Hey Rogerio_88 , I al testing a lot of cells today, and I also got a lot of big numbers, such as 3000+ but I also got smaller one, like 1367, 1682 ... and I don't know if it is correct or not, did you come up with any answer to your question?
No your calibration on the module is not good or the resistance you are using changes its value after heating so Change the resistance it might work
Very interesting,thk y for video.
Most welcome dear
Sir,... I've followed ur instruction.. it give the best accurate on voltage, but not with the current, now my module show the wrong current, and i can't make it better, can u tell me how to fix it? Or my module is broken? thanks for your regard
Calibrate it once again with the same method but make sure the current controlled module should be accurately set to the said current then the ZB2L3 will be calibrated accurately
After carrying out this procedure, my module only shows error 5, is there a way to restore the factory configuration, or do I have to buy another module and not touch it again. ?
can you show me the picture
hahahahahaha
In mine ZB2L3 All things are but ah and a are not showing 😢
Video is so accurate! But: Autor cannot show (it's missing) real adjusting of current during calibration prosess - as the voltage adjusting.
And Please - Include english text on most important points of video.
Ok sure dear surly I will add English
TP4056 is full charge cutoff is 4.2v but 32650 full charge? i dont know
Helped a lot
Module k bagir calibaration ho sakti ga agr koe charger use kar lia jay ?
no dear kion k charger constant voltage b nahi deta or constant current b nahi deta voltage or current constant hona must hai
@@RizwanSaeed thank u so much brother ...
@@mydiy8555 you are most welcome 😘
Im using adaptor with 10v DC and 2A. Is it ok?
Check with multimeter the Amps
how to set the amp in xl 4015?
the knob is given on the module to set the current and voltage
ben yaptım kalibrasyonu voltaj doğru ama pilden çekilen akım gerçekte 880mah gösterilen değer 660mah neden olabilir
I want use 32650 lifepo4 it is possible to use and how to set buck module for 32650 and measurement
yes you can no need to adjust it only draws current from cell through resistance and measure its capacity
this can. measure voltage upto 12v so Lipo batteries voltage are far less then 12v use it without any hesitation
Assalam walekum Bhai ye tester 15 volt 3 amp ka cell support karta hai lifpo cell 6 ampere ka hota hai to 3 ampere se jyada ka cell ko support kare ga kya
Dear yeh tester Hai jis nay cell ko test karm Hai ap jo resistance add Karin itna current draw Kar k testing Kar day ga
Pher yeh keh skaty hain k ap nay yeh cell 1 amp ya 2 amp discharge current pay test kia Hai
Or kitny mAh yeh count Kar skata Hai wo 9999mAh hain
Volatge yeh 12v tak support karta Hai means 6 volt ka cell test ho jaiy ga
@@RizwanSaeed meena ham 6000 mah ke cells ko test kar sakte hain na?
Bilkul
@@RizwanSaeed thanks bro mai aap ke channel ko subscribe kar diya
Amjed lahore very good nice ❤❤❤
Bhai Jan Mary pass ase 3 modules hain vo celebration ni le rahy
Same ap ke Tara kiy 3button press at time but no response display
Plz plz tl me
please follow the details of the don't skip any step
Thanks, helpful
I apply this formula for HW-586 module. But It's not work. Can you help me for hw-586 module calibration?
ye seen mary sath b hogaya is b.c k chakar men hahahaha oooo show hoty hn or error 5😅😅
Same problem facing
You got solution?
@@maheshsasane7273 No, I buy new one
Thanks dear. Very good
TP 4056 module i want use charging purpose to 32650 its possible
don't use to4056 for 32650
Any suggestions?
you can use CC And CV circuit to charge according to data sheet setbyhe voltage of that circuit it will work perfactly
you are from?
India mumbai
Which constant current module is this ?
dear it's XL4015
Showing error2. Solution please
what is the error
DC Voltage step down, name ? module no?
buck module works both ways
@@RizwanSaeed whats is module name?
just search for buck module in Ali express
@@RizwanSaeed thanks, XL4015, Is it correct?
@ yes exactly and you are from?
can you please write step by step calibration in english?
sure I will
@@RizwanSaeed
Where is the description in English? I am waiting for you.
Greetings from Saudi Arabia.
IN SHA ALLAH soon I will. upload in description
@@RizwanSaeed
May Allah bless you.
The first calibration step after entering the calibration displays the 0u0A; short connect both positive and negative input terminal and press the "OK" button
Next, the display will show J10u; apply 10.00V DC between the input positive and negative terminal and press the "OK" button again.
The display will show J2.0A; apply 2.0 A DC current between the input terminals and press the "OK" button to complete the calibration.
Please add english translation, Thank you
Nice
Error 2
Error 3