May be it will trigger the circuit whenever the water level is below the first wire ! That's why It will make the pump frequently on and off , which may cause the pump to burn !
You are right. Any slight dip in the water level below the 9V supply wire will switch ON the motor. Please suggest a circuit to ensure the motor switches ON when the water level reaches bottom. Then only it will be useful.
Very good video but I don't want the water tank is fully empty, I hope you understand my point the motor should start minimum one feet of water in the tank.
I think u r bengali. Tai bengali te likhchi. Ami eta toiri korechi and khub sundor cholche. Kintu tindin cholar por jakhon motor cholche takhon telay theke jore jore hissing sound asche. Ami 12 volt dc 30 amps relay use korechi half hp motor chalanor jonno. Even tank theke je wire eseche oi gulo o notun lagiyechi. Ami bujhchi na hissing sound kno asche ..
So basically when the tank is full your 9v battery is supplying dc current to the relay which is keeping the motor shut but that way it wud keep draining ur battery till the tank is full, i am not sure how long that battery wud last that way. Also even if the water level goes down a bit that top wire it wud trigger the motor which means motor will start and off several times in a day
This is very very use full project. I agree with you, but here is a trick which is very usefull for save battery or 12v charger supply or auto ON AND OFF problem for the motor. It is that when you are connections between battery to relay you need a two way button (switch),it is called as BYPASS and AUTO mode. I hope that you would have understood.
On more things is that for 9v battery use only normal switch and for 12v power adapter or charger use two way switch, this is tricky. 💯% solve your problem.
Automatic water motor on/off video is good but one thing i want to know over here is jab pani piche se aye means (government mcd water supply) uss sameh motor start hoh in between agar pani band ho jahe toh motor automatic band ho jaye. Is this possible for you to make that video with diagram. please reply. Thanks.
Bhai mere pass 2hp Ka single phase submersible pump Hain to use ye technique kaam aayegi kya? Kyu ki submersible ke pump Ka condenser starter mein laga hota Hain to iss case mein kaise kare plzz rpy fast...
Hi nice video, can you please make full video with circuit diagram control sump tank wiring to stop pump dry run along with over head tank full one circuit diagram.
Hi...I use 2 tanks...lower and upper. Motor pulls water from lower tank and delivers to upper tank.i want the motor to stop as soon as water is about to finish in the lower tank. So that the motor does not run dry. Please help.
Use relay in series to shut motor as soon as water runs out in lower tank. , Relay common to be connected to Phase , NO to be connected to Motor , Relay coil positive to be connected to 12V positive, Relay negative to be taken to lower tank, from lower tank Other separated wire to be connected to -ve of 12V power supply. Put these two wires at appropriate level at bottom so that before completely empty , it should disconnect the motor from operations. As soon as water is over, Coil of relay stops functioning and relay stops (NO is disconnected and relay is at NC position) Visit espicestore.com for such products
Is circuit mae bhi to same dikkat hae. Water level max reach karega to power supply band ho jayega. But water level jaise he yellow wire ke neech pouchega (which is not minimum level) then again circuit on ho jayega... So bar bar on off hota rahega circuit. Maximum level ka off banaya. But minimum level mae on to banao...
Bhai relay k no se ek buzzer laga le Jaise hi level highest Hoga so motor off or buzzer bajega then bnd kr dena motor tm sb automatic chahte ho to almost 4-5k cost ayga cuz usme tmhe plc Chahiye or ya fir tm Kisi project bnvane wale se microcontroller based switching device bnva sakte ho 800-900 m
Do you want to stop Water tank overflow. *For water level controller or Automatic motor/pump controller* Call/whatsApp 7903 827 839 We deliver to all India. *Sarans Automation*..
Ye automatic off hothe. Tik hei. Lekin motor hamesha chalu rahathe. Takkikki pani ek dum neeche ayatho automatic on hona hahiye aur maximum level ayatho off hona chahiye. Aise project bananase bahut log ko faitha hoga.
Thank you sir. It is useful. But sir I want to konw something else. I have a 8Hp water pump. I want to know that, is it possible to make automatic voltage level controller? When line voltage less then 200, pump automatically switch off and when line voltage 200 or more, pump automatically turn on. I mean, when voltage reach lower level pump automatically switch off and when voltage level reach higher level (what i have need) then pump automatically turn on. is it possible or not ? Sir. Like to automatic water level controller. If it is possible please please please make video about this or give me instruction about this. Please sir.
Do you want to stop Water tank overflow. *For water level controller or Automatic motor/pump controller* Call/whatsApp 7903 827 839 We deliver to all India. *Sarans Automation*...
Bhai apne Apni video main jo btaya ha k jb pani wire ko lagta ha to motor bnd ho jati ha mujhe yeh btain k main wiring ko ulta kese kr sakta hun yani jb tank khali ho motor bnd ho jaye or jb tar ko pani lage motor on ho jaye plz mujhe wiring ki diagram jaldi se jaldi send karain
yes i have made it , fully automatically , no need to even touch the switch . when the water reaches at 50% the pump will start and will turn off when its full without overflowing .
Hi I would be grateful, if you could suggest some solution for below I have three overhead tanks, which feeds my three storied house through gravity. These tanks are filled by means of a 1000 HP motor installed in line with municipal water supply. a) Now the problem is Physical monitoring of motor and keep a watch of water, when it comes and goes. b) Tanks monitoring. c) Doing the above routine every day is a cumbersome task. So I would like to have a system with municipal water supply, which should be able to do the following: - a) Auto start and stop the pump with incoming municipal water b) At the same time the pump should be controlled based on water level in tanks and the system should be able to perform all below conditions:- i. In case the municipal water is coming, and my tanks are full, the pump should not run ii. If the tanks are empty and municipal water comes, the pump must start automatically iii. The water is coming, and if the tank gets filled in, the pump should also stop
It is only model ,but in practically it will not work. The motor will get cut off when it touches high level as the water gets down slightly the motor gets ON.Inthis For practical circuit go and watch YOU TUBE CHANNEL " PRABHA KNOWLEDGE POINT ".
Bhai ye motor to tab bhi chlti rahhi gi jab corporation pipe mai pani nahi hai😁😁😁 so essa kuch batyo ki corporation ka pani aate hi motor chal jye ans pani jate hi motor band ho jye..
Team, Hamare paas Lubi ka 1hp mater hai, usme ek problem aati hai ki moter ko ON karte hai to 25min baad chalte chalte apne aap off ho jata hai, pls share solution
Maine mere tanki se pani khali karne k liye cooler wala motor pump lagaya hai jise 1 ghante me automatic band ho jana chahiye Kyoki 1 ghante me tanki ka pura pani khali ho jata h aur kabhi kabhi mai motor band krna bhul jati hu To ye circuit kese banega batayen
mere pas 1HP motor hai muze corporation ka pani kabhibhi ata hai pani ane ka fix timing nahi hai, mai 4 th flor par rahata hun pani aneke bad motor chalu karana padata hai,muze pani atehi motor chalu ho aur pani jate hi band ho aisa sercuite bana do.....pani 15 /25 minit tak hi ata hai aur storege tank 25 hajar liter ka hai lekin ghar par pani ane ke time koi hota nahi
This is useless... pump will be off when water touched to upper wire and will start as soon as water level receding below upper wire. Thus the motor will off and on very frequently
Fatafati bhai..darun ekta jinish shikhlam ajj.Dhonnobad.
Water level kham hothehi motor chalu hoga, mathlab bhar bhar on hogana, brother..
Yes
May be it will trigger the circuit whenever the water level is below the first wire ! That's why It will make the pump frequently on and off , which may cause the pump to burn !
This circuit is suitable only for turn off the motor......
You are right. Any slight dip in the water level below the 9V supply wire will switch ON the motor. Please suggest a circuit to ensure the motor switches ON when the water level reaches bottom. Then only it will be useful.
Thank you so much, very nicely explained.
Nice and very helpful video sir..thanks for share.
Very nice bro thanku for all thing.
Chaho jo NPN transistor le le kaam krega? Like TIP31C, ,TIP122?
Very good video but I don't want the water tank is fully empty, I hope you understand my point the motor should start minimum one feet of water in the tank.
I think u r bengali. Tai bengali te likhchi. Ami eta toiri korechi and khub sundor cholche. Kintu tindin cholar por jakhon motor cholche takhon telay theke jore jore hissing sound asche. Ami 12 volt dc 30 amps relay use korechi half hp motor chalanor jonno. Even tank theke je wire eseche oi gulo o notun lagiyechi. Ami bujhchi na hissing sound kno asche ..
Very good
👍🏼
So basically when the tank is full your 9v battery is supplying dc current to the relay which is keeping the motor shut but that way it wud keep draining ur battery till the tank is full, i am not sure how long that battery wud last that way. Also even if the water level goes down a bit that top wire it wud trigger the motor which means motor will start and off several times in a day
Absolutely right! Even if one mm water goes down , motor starts for few seconds. This is not useful project , but yes for learning its better
This is very very use full project. I agree with you, but here is a trick which is very usefull for save battery or 12v charger supply or auto ON AND OFF problem for the motor. It is that when you are connections between battery to relay you need a two way button (switch),it is called as BYPASS and AUTO mode. I hope that you would have understood.
On more things is that for 9v battery use only normal switch and for 12v power adapter or charger use two way switch, this is tricky. 💯% solve your problem.
can we connect it before submersible motar starter if its off automatic submersible starter will trip (once power off its can not start automatic) ?
Pani ka level kitna niche jane k baad motor phir se automatic chalu hoga?
Automatic water motor on/off video is good but one thing i want to know over here is jab pani piche se aye means (government mcd water supply) uss sameh motor start hoh in between agar pani band ho jahe toh motor automatic band ho jaye. Is this possible for you to make that video with diagram. please reply. Thanks.
Bhai mere pass 2hp Ka single phase submersible pump Hain to use ye technique kaam aayegi kya? Kyu ki submersible ke pump Ka condenser starter mein laga hota Hain to iss case mein kaise kare plzz rpy fast...
Acha video hai sir but plz elaborate kijiye , how things working in this circuit
Good module, please also make a module with facility to stop motor without water in supply. also suggest from where purchase such a readymade module.
Underground tank ke liye bhi circuit banao
I want to turn off moter when water not available in pipeline.
Many time moter is heating without water.
Tell me how it auto on.
How to run this motor.
Hi nice video, can you please make full video with circuit diagram control sump tank wiring to stop pump dry run along with over head tank full one circuit diagram.
Khaali hone k baad duwara On hoga ya manual on karna padega ?
Tank m thoda sa paani khali hote hi motor on ho jayega, aise to turant turant motor on hoga, you should use timer, I mean 555 IC.
how its used for village home if water supply of inlet is stop mottor is off as soon as water supply start motor is start
How to do the reverse? When water is empty in the below tank at the bottom, submersible motor should turn off?
Hi...I use 2 tanks...lower and upper. Motor pulls water from lower tank and delivers to upper tank.i want the motor to stop as soon as water is about to finish in the lower tank. So that the motor does not run dry. Please help.
Use relay in series to shut motor as soon as water runs out in lower tank. , Relay common to be connected to Phase , NO to be connected to Motor , Relay coil positive to be connected to 12V positive, Relay negative to be taken to lower tank, from lower tank Other separated wire to be connected to -ve of 12V power supply. Put these two wires at appropriate level at bottom so that before completely empty , it should disconnect the motor from operations. As soon as water is over, Coil of relay stops functioning and relay stops (NO is disconnected and relay is at NC position) Visit espicestore.com for such products
My motor always on. when tank full but my motor not off.give solution
Please reply as soon as possible
Hi sir 12v 20A realy ac or DC
Appreciated. Thank you.
0.5 hp pump ko chalega kya
4 hp ke liye konsa relay use kare aur kitne dc volt & Ampiar ka power supply use kare
Is circuit mae bhi to same dikkat hae. Water level max reach karega to power supply band ho jayega. But water level jaise he yellow wire ke neech pouchega (which is not minimum level) then again circuit on ho jayega... So bar bar on off hota rahega circuit. Maximum level ka off banaya. But minimum level mae on to banao...
this circuit is used to off the pump at deserve level.
Bhai relay k no se ek buzzer laga le Jaise hi level highest Hoga so motor off or buzzer bajega then bnd kr dena motor tm sb automatic chahte ho to almost 4-5k cost ayga cuz usme tmhe plc Chahiye or ya fir tm Kisi project bnvane wale se microcontroller based switching device bnva sakte ho 800-900 m
भाई वीडियो तो अच्छा है लेकिन यह फिर से चालू भी हो जाती हैं लेकिन मुझे अपने हिसाब से ऑन करना हो तो केसे करे लेकिन बंद तो फूल होने पर हो
Use PLC
Can we use two 7amp relay and connect it in parallel to create 14amp ralay??
Sir its working, but how to install this circuit in submersible water pump pannel board, please make a video
Do you want to stop Water tank overflow.
*For water level controller or Automatic motor/pump controller*
Call/whatsApp 7903 827 839
We deliver to all India.
*Sarans Automation*..
Ye automatic off hothe. Tik hei. Lekin motor hamesha chalu rahathe. Takkikki pani ek dum neeche ayatho automatic on hona hahiye aur maximum level ayatho off hona chahiye. Aise project bananase bahut log ko faitha hoga.
Thank you sir. It is useful.
But sir I want to konw something else. I have a 8Hp water pump. I want to know that, is it possible to make automatic voltage level controller?
When line voltage less then 200, pump automatically switch off and when line voltage 200 or more, pump automatically turn on.
I mean, when voltage reach lower level pump automatically switch off and when voltage level reach higher level (what i have need) then pump automatically turn on.
is it possible or not ? Sir.
Like to automatic water level controller.
If it is possible please please please make video about this or give me instruction about this.
Please sir.
Im using an automatic switch which allows me to set minimum and maximum v and amp to on and off supply.
Yes it is possible.
this circuit is of no use the tank remains on terrace while the motor remains in ground floor we cant stretch so much of long wire from. tank to.motor
Do you want to stop Water tank overflow.
*For water level controller or Automatic motor/pump controller*
Call/whatsApp 7903 827 839
We deliver to all India.
*Sarans Automation*...
How to make dry run circuit with Same motor and with components used
Bro its good but how to we got motor on/off u have to show indication lights with led and becouse of we are not to be see motor every time ok thanks u
Good
how value divot dear
Bhai apne Apni video main jo btaya ha k jb pani wire ko lagta ha to motor bnd ho jati ha mujhe yeh btain k main wiring ko ulta kese kr sakta hun yani jb tank khali ho motor bnd ho jaye or jb tar ko pani lage motor on ho jaye plz mujhe wiring ki diagram jaldi se jaldi send karain
Very nice video thanks a lot....I have seen your previous video in this subject....very informative and well explained....thanks a lot once again
tika tika tika pleas explain how motor restart when water low
And i have adoubt
How to calculate amps for wires
&
How to calculate watts , rating on electrical things
This is a large topic.....I can't elaborate this one in comments....
Sir ap mera ek help karenge. Sir water pump motor ko remote control kese bana sakte he relay ki madat se. Keya ap isme ek video banayenge.please sir.
how to control three phase motors ?? any possibilities ???
yes i have made it , fully automatically , no need to even touch the switch . when the water reaches at 50% the pump will start and will turn off when its full without overflowing .
@@allown7107 please send me the circuit diagram. I make duya for you brother
Thiik ha
1k resistor: how many watt
1n4007 diode: how many amp?
Please reply
Hai, Brother Precious Video, Thanks You Sooo Much, Maine Redy Kiya hai, Useful Thanks You, GOD BLESS YOU
Hi 9wt battery ki jagah pe dusra kya use kar sakte hai
Or battery lagana jaru ri hai
aap kohi bhi 12v power supply use karsakte hai....
AGAR POEWR SUPPLY USE NA KARNA HO TO?
AND A JO VIDEO ME BATA YA HAI A SIF OFF KA HI HAI NA?
Aap kohi bhi 9v ya phir 12v power supply ya phir... Battery use kare.. Circuit ko power dene keliye
IS MAI SIF OFF HI HOGA NA
how much current would be flowing on the base-emitter junction ?
Hi I would be grateful, if you could suggest some solution for below
I have three overhead tanks, which feeds my three storied house through gravity. These tanks are filled by means of a 1000 HP motor installed in line with municipal water supply.
a) Now the problem is Physical monitoring of motor and keep a watch of water, when it comes and goes.
b) Tanks monitoring.
c)
Doing the above routine every day is a cumbersome task. So I would like to have a system with municipal water supply, which should be able to do the following: -
a) Auto start and stop the pump with incoming municipal water
b) At the same time the pump should be controlled based on water level in tanks and the system should be able to perform all below conditions:-
i. In case the municipal water is coming, and my tanks are full, the pump should not run
ii. If the tanks are empty and municipal water comes, the pump must start automatically
iii. The water is coming, and if the tank gets filled in, the pump should also stop
It is only model ,but in practically it will not work. The motor will get cut off when it touches high level as the water gets down slightly the motor gets ON.Inthis For practical circuit go and watch YOU TUBE CHANNEL " PRABHA KNOWLEDGE POINT ".
Bhai ye motor to tab bhi chlti rahhi gi jab corporation pipe mai pani nahi hai😁😁😁 so essa kuch batyo ki corporation ka pani aate hi motor chal jye ans pani jate hi motor band ho jye..
PART KA PURA LIST EK SATH DIJIYE
I want this product
Bro 9v battery connection hai na vahape 5v charge adapter chaltha hai na bro
baar baar on off hoti.h motor isse motor burn ho skti h..Ek minimum level ke baad motor on ho iske liye koi circuit h
Sir, you have to use another circuit which is stable. Please message me to know more ~!
Bhai main water line me jabi pani aata hai tabi motor automatic on kaise ho
Team,
Hamare paas Lubi ka 1hp mater hai, usme ek problem aati hai ki moter ko ON karte hai to 25min baad chalte chalte apne aap off ho jata hai, pls share solution
Maine bhi banaya pr automatic off nhi hoti hai
Bhai motar chalu ho gya parantu band Kaise hoga
Maine mere tanki se pani khali karne k liye cooler wala motor pump lagaya hai jise 1 ghante me automatic band ho jana chahiye
Kyoki 1 ghante me tanki ka pura pani khali ho jata h aur kabhi kabhi mai motor band krna bhul jati hu
To ye circuit kese banega batayen
Use a timer circuit for 1 hr... Which will trigger by this setup
It’s not perfect because it may harmful for the pump.
Sir ji 24 v ka reley kaam karega Kya
ha ..lekin 24v ka supply use karna padega
AAP VIDEO ME CIRCUIT DIYAGRAM BHI DENE KI KUPA KRE YA TO DIYAGRAM KI LINK DIJI A
Project Mota kaise kare
দাদা আপনিতো মোটর বন্ধ হওয়াটা দেখলেন । কোন লেভেলের নিচে জল গেলে মোটর চালু হবে সেটা কোথায় ?
amar channel check korun apni video ta peye jaben
aisa curkit btao jo paani ane ki surat me on ho jaye
Bhai 0.5 k liye kon sa relay le
10 amps relay will be OK.
@@TheBreakoutTraderAKASH Bro. 0.5Hp Motor ke liye kitne kitne power ka equipment kya kya lgega please tell me
U r bengali. Where r u from?
It's work bro
For practical circuit watch this video
ua-cam.com/video/OJ8kd8VPfQ0/v-deo.html
Whr do u live
West Bengal
District??
Sir muje automatic on krni hh sirf
This Bhai talk too much thikae. lol
When a power cut for some seconds then the water pump automatically on . although the the tank was full.I use a 12-0-12 transformer for power supply
mere pas 1HP motor hai muze corporation ka pani kabhibhi ata hai pani ane ka fix timing nahi hai, mai 4 th flor par rahata hun pani aneke bad motor chalu karana padata hai,muze pani atehi motor chalu ho aur pani jate hi band ho aisa sercuite bana do.....pani 15 /25 minit tak hi ata hai aur storege tank 25 hajar liter ka hai lekin ghar par pani ane ke time koi hota nahi
Please contact I need help at Delhi.
This is useless... pump will be off when water touched to upper wire and will start as soon as water level receding below upper wire. Thus the motor will off and on very frequently
kya ye tank khali hone ke baad auto me on bhi ho jayega ya sirf off hi ho payega
kyu ki muje ye jaha SE pani aata hh vha PE lgana hh taki sube muje utna Na pdde or motor apne aap on ho jaye
In that case use 4017 ic..
Bhai no milega kya apka
1
Replw to me
Vai banglai bolo osubidha nei tomar hindi ta sunte kharap lagche banglai tech channel khub kom e ache
amar bondhurao bolchilo....banglate tech channel serokom nei....kichu channel er idea dao....banabo...
How To Bro obossoi debo.
Tomar what's app no. Ta amar mail e send koro. Mail id -- sbasu@pneucisrobotics.com
answer me sir
Aisa curkit btao jo line me paani ane ki surat me on ho jaye
Good idea... I will try..
Thanks for reply