Coaming and Sanding - Kayak Class Completion

Поділитися
Вставка
  • Опубліковано 17 лис 2024

КОМЕНТАРІ • 15

  • @actionjackson9121
    @actionjackson9121 4 роки тому +1

    watched all the videos to this point Nick...Im a 39 year old trim carpenter who lives on a lake and have a small shop. You sir, have inspired me. Cheers!

  • @douglasreeve3591
    @douglasreeve3591 4 роки тому +1

    After taking your class a couple times, it's fun seeing you finish off one of the class built boats. I hope you and your family are doing well.

  • @04lj33
    @04lj33 4 роки тому +1

    Thanks for all your time and hard work you put into these videos! Really enjoy watching and seeing ways I can improve on my next kayak!

  • @jwrappuhn71
    @jwrappuhn71 4 роки тому +1

    That was excellent Nick.

  • @frankleoni547
    @frankleoni547 4 роки тому +1

    Great instructions and tips Nick!

  • @doughermann9975
    @doughermann9975 4 роки тому +1

    Nick, sorry your June kayak class got cancelled. It would have been fun and informative! Will miss being at WBS this year. Regards, Doug H.

    • @NickSchade
      @NickSchade  4 роки тому

      I am planning on there being other years. For now I can make some videos.

  • @1a1u0g9t4s2u
    @1a1u0g9t4s2u 4 роки тому +1

    Nice tip on how to remove drips

  • @MrEfarmer
    @MrEfarmer 4 роки тому +2

    What is the brand name/model number on the hand sanding pad with vacuum port? Never seen that before. Thanks, Edward

    • @NickSchade
      @NickSchade  4 роки тому

      Mirka 91402 2 3/4-Inch by 5-Inch Grip Faced Abranet Vac Block : amzn.to/2wsUDUp

  • @jimdodd3462
    @jimdodd3462 4 роки тому +1

    The Carbide paint scraper is easier for these Old hands, feathering those edges and drips. I'd worry about the spots that weren't sanded white, showing up as blotchy ?

    • @NickSchade
      @NickSchade  4 роки тому +1

      I have never found the carbide paint scrapers particularly sharp. They don't dull easily, but they aren't really sharp. A good steel scraper can be sharpened to a really fine edge and is just much more satisfactory. But the rasp works great also.
      One thing about the initial fill coat I squeegeed on is it acts as a bit of a primer coat. I do not seem to have any problems with blotchiness. Note, the scrub down with ammonia and water also scuffs the surface and helps prepare it for epoxy.

    • @jimdodd3462
      @jimdodd3462 4 роки тому +1

      @@NickSchade The sharpness of my scraper was good, but the difference between my use and yours ? I scraped while the epoxy is green, within a day or two, not six months later, Enjoying your videos !

    • @NickSchade
      @NickSchade  4 роки тому +1

      @@jimdodd3462 That does make a difference.
      I just figured out that my previous reply referred to something on the video I was editing at the time and not something on the video you were watching.
      You will see my fill coat procedure on the next video, with no blotching.

  • @АлександрВаулин-ь5к

    :-) OK !!!!!!