Sir I HAVE MAD RESPECT FOR YOU. I BROKE MY ROD TIP HEADING OUT THE DOOR FOR A TOURNAMENT THIS WEEKEND I COULD CRY. I SAW YOUR VIDEO AND WENT TO WORK. I HAD A MICRO ROD YOU KNOW REALLY THIN AT THE TOP. I GOT A SHAKEYHEAD HOOK THAT WOULD FIT CUT IT AND WENT TO WORK. I FEEL MUCH BETTER NOW. YOUR VIDEO SAVE MY HOME BECAUSE IT WAS GOING TO HELL TO TALK TO ME FROM NOW TO THE WEEKEND 😆 🤣 😂 😹 😆 SO GLAD GOD LEAD ME TO YOUR VIDEO AND TO NEVER GIVE UP. THANK YOU 😊 🙏 😊 🙏 😊
I used fiberglass sticks. They sell them in different sizes at Harbor Freight. $8 for a small pack. Worked perfectly with thread wraps and Epoxy. Now time to go test it out on some big Pike 😎🤙🏽
Я много лет занимаюсь ремонтом удилищ. Мой совет- ни в коем случае не пытайтесь отремонтировать бланк так, как показано здесь, колено будет в дальнейшем расщеплено в месте стыка. Внутреннюю вставку следует сделать из того же материала, что и удилище. Склеивание лучше выполнить эпоксидным клеем, супер клей , со временем становится хрупким и выкрашивается . После того как вы соединили поломанные части, нужно демонтировать кольца на бланке выше места перелома. Подобрать кусочек какого либо колена от удочки, которое плотно оденется на поломанное удилище в месте склейки. Достаточно трубки длинной 6-10 см.сажаем её на эпоксидку. По краям трубочки делаем нитяные бондажи и покрываем их эпоксидкой. Устанавливаем на место кольца. Ремонт окончен. Подмотку колец можно производить обычной ниткой, использовать для этого плетёнку нет смысла. Момент и подобные ему клеи для работ по ремонту удилищ не годятся.
Серьезно? Надо моему спиннингу об этом сказать, что уже 3 года работает, отремонтированный именно так. Видео не идеально. Супер-клей нужен хороший, гелевой консистенции, стержень дб обработан на концах (закруглен). Вместо нити, используем супер-клей + сода. Финальная обработка. Спасибо.
_Solid metal placed in the rod can make the part on the rod connection stiff and easily broken due to strong pressure by the fish, i used a fiber stick from amazon for only 2 dollars for 100 cm_
Never use a nail in a fly rod. You need to use carbon fibre with similar bending properties and a matching taper. The action will be affected and it will inevitably break otherwise.
Thanks - it works! I just repaired my 9' fly rod with a break in the first section. Had to find something thincker than a nail to fit but it seems to work well.
I've fixed a couple of fly rod tips in a similar way. Since the rod is very narrow at the tip, a 2" sewing needle works well as the insert (you might need to clip off the eyelet). Sewing needles seem to have enough strength and stiffness, plus you can find one in a diameter that will fit snug enough. Alternatively, you can get loop end wire shafts from a lure making supply store which are made from stiff, springy steel (I used .035"). Also, you'll need to add at least 1 but preferably 2 sewing needles (or wire shafts) on the outside of the break as splints. Glue in the insert then wrap the splints and spread a thin layer of epoxy over the threads. I use dental floss because its strong and flat. Waxed or unwaxed floss works as long as you coat with epoxy. Put the splints on the sides of break and not along the top/bottom. This way there is less of a bump along the bottom where the fly line runs. I have mixed results as to whether the action and accuracy of the rod is affected with dry flies (I notice no issue with nymphs) but at minimum you can fish until you order a new tip and then you'll always have a backup tip.
I’ve used a piece of another broken rod to insert as the splint between the broken pieces or have slid the broken pieces into the splint instead of using a nail. When gluing the pieces together with super glue, if you sprinkle baking soda into the wet super glue it will instantly set up as hard as a rock and fill the gaps between the rod pieces. I also use 2-part clear epoxy on the rod wrap threads instead of super glue. I have also shortened the rod until I got the lower section large enough for the broken tip section to slip inside it before gluing.
I have several pieces of broken rods that I save to get a good fit with a taper like the rod I'm repairing . I use fine steel wool to ruff the rod before applying epoxy at the gap and to cover the thread . Great job ....looks like new ,and actually is stronger than new .
I do the same using rod repair thread and also just ordinary polyester sewing thread as well. I have bought carbide rod pieces at 1.5mm and hollow carbide tubes at 2.00 and 2.3 mm using them to make rod tip repairs. Turned out pretty good.
Good Evening My Friend blueparay, Thank You for your detailed video on "How To Repair A Broken Fishing Rod." I to have experience a broken rod or two in my 35 year quest in fishing multiple spicese of fish! I to once implied the same techinque to repair a broken rod that a BEST FRIEND gave me. 🙂I Treasure the fact that YOU took the Time and EFFORT to Divise such a Detailed Video. Thank you once again my Fishing Friend for Being So Understanding and Compassionate for Our Sport of Fishing and the Millions of Viewers that watch Your Program! You are a TRUE Inspiration to US ALL!! 🙂MAY GOD "BLESS U & U'r Familiy! Sincerely, Mr. Carl Joseph Gwizdala aka "DESPERADO." 🙂
Just done this today. only thing I done different is put a coat of clear over the nylon and cured it under a uv light .Turned pretty nice glad to have my rod back .
Гвоздь это конечно круто!, долго не протянет, вместо гвоздя нужно(желательно) использовать гибкую вставку, например от сменных вершинок, живучесть повышается.
Я вообще внутрь оправку из плотной бумаги, пропитанной быстросохнущей эпоксидкой, вставляю. А когда схватится - снаружи углетканью, опять же на эпоксидке, сверху приматыааб скотчем. Потом скотч срезаю, и зашлифовываю наждачкой. Получается незаметно, и крепко, и вес и строй практически сохраняется.
I'm the kind of person that sees value in everything. And I also get a sentimental value from things I repair. Today I broke a rod like an idiot and I really want to buy what I need to repair it. Seeing this done with what I believe to be a watery cyanoacrylate, some thread and a metal is reassuring. Unfortunately my rod is in a bad way, it needs a guide and has two breaks in the tip. I think it's a little out of my hands because it broke in the first place because I tried to shortcut life and use a stone bench grinder to attempt to remove a broken guide, slightly scratching a little deep in the the rod creating a weak point where it snapped, and somehow snapped like 10cm down the rod in another spot. It's like my only decent rod too I'm so sad..
Saran aja ya mas Setiap beli rood baru usahakan top Rood lilit pe mulai dari bawah sambunggan hingga ring bagian atas sambungan (jika di hitung dari bawah no2) ini efektif buat rood yg bertipe holow. Semoga bermanfaat
@@DyanSinchan iya om gak ada efek ama lengkungn ataupun beban di rood alias tidak ada efek samping sama x. Tetapi berefek ama kekuatan saja meskipun sederhana tetapi saya buktikan dengan nahan tarikan baramundi dengan bobot 6kg tak ada dampak ama lengkungn nya om pokoknya kuat dah(rood jhoncoo 2.1m)
I've thoroughly enjoyed your knot tying videos!😊 I started building rods (Professionally), in mid 70s (I think 1976), and I don't mean building a fly rod, as those are ridiculously easy to put together!! I'm talking about boat rods with roller-guides and pack-rods (4 or 6 piece high quality rods), out of a 1 Piece Blank, meaning that I had to make my own ferrules!! And then I'd do anything from "perfect" Half & Half Diamond wraps that took 8 to 10 hours non stop!! By half and half, I mean half the Diamonds would be one color and the other half another. And many more like the U.S. flag with the stars and all, or Eagles etc. and it would take many wraps of thread to create. At any rate, the rod with the Nail would have one heck of Dead Section!! This of course would be no problem with even a Trophy Bass, but certainly not with a Big Steelhead or any fresh Chinook/King Salmon (fresh out of the Pacific Ocean)!! I still catch a good number of Kings going to 40 pounds or larger!! Again I can land any Bass with just about any rod or hand-line!! Someone else mentions the use of broken rod pieces, which makes a lot more sense!!
I'm wanting to make a 1 piece rod into a 3 piece and I was brainstorming ways to make it fit into itself, it's hard to find info online about it that I understand. Maybe you can link me a video to help. I was just wondering if using apoxy and peices of another blank to make a stopper for how far the peice will insert and using 20lb braid+apoxy to keep the blank from splitting out under load bc I'm going to need to do significant stock removal to the ID on the female end for the male end to fit. Is the male end filled with fiber/apoxy or is it just capped off. I have so many questions about how a broke 22 year old can make ferrules in his garage but I doubt you'll see my questions bc your comment is a year old , worth a try tho lol
I just bought a rod online that showed up busted like this. I was going to just return it, but I think I'll consider it an investment in self sufficiency and just go ahead and figure out how to fix it instead. Thanks for the inspiration.
Гвоздь, как мне кажется, все-таки надежней - в этой части лучше, что бы изгиба больше не было вообще. Но, вот края гвоздя бы сделал максимально шаровидными, что бы не было места концентрации усилия об точечное место в виде заусеницы. А еще, неплохо бы, чтобы до и после гвоздя какой-нибудь наполни тель в виде герметика был.
@@andreykalita1205 в районе гвоздя (где он заканчивается) будет новая поломка. Я так пытался ремонтировать бамбуковые удочки, когда мне было 12 лет. После того, как подрос, понял, что необходима трубка снаружи.
I really wish I would have known this technique many years ago. After coming back from a bass fishing trip to Florida I was unloading my boat at home and my favorite rod had it's tap broken off buy the screen door closing too fast. I had tens if not even hundred of thousand cast on that rod. It was so old that they no longer made it so I could not replace it.
I hope it wasn’t a $400 rod, like the one I broke the top off of in 2 places, before I’d used it for a month! Or the $300 rod I broke in a car door a month later. Lessons learned!
I broke mine in a car door shortly after building it. It was the first fly rod I ever built. I came up with the same idea but I used epoxy at the time many years ago. Thanks
If needs must it’s a solid repair but it would create a flat spot in the blank and affect the action of it when put under strain. I cannot fault you for saving your rod though👍
today my fishing rod was broken, it was very similar to the broken position like in the video, now I found this video as a solution, thank you very much
just bought a BNM super sensitive and broke first time I used it. will try to take it back but if not this is a super solution. will use epoxy instead of super glue
who hasn't found a discarded broken rod along the shore? I always gather the tip end to use sections as an insert instead of a nail. Strength is there plus the flex.
Если уже таким способом ремонтировать то хотя бы для приличия края у гвоздя на наждаке закруглил бы ато острые углы при нагрузках со временем расколят стеклопластик а по нормальному надо бы стеклопластик пустотелый вставлять внутрь ИМХО :)
same it happened when I was taking algae off of the rod and then I heard the snap noise and a bunch of tension released form the line and the rod, I looked at my rod and a foot of the rod came off and I just thought "there is no way that just snapped my rod."
Brought my 4 year old with me to the river, used the same rod since I was 16, bought a new one for bobber and egg fishing for salmon nicest rod I've had a nice 9'6 okuma guide select pro $200 or so...stepped on 😔
Thanks its happened to me so many times and I would just trash it or in my boat getting snapped on brush going to a favorite spot and bam . Now I'll put this in my tackle box, thanks again.
I would personally use fiberglass then epoxy that in before wrapping, something as rigid as metal seems like a bad idea in a rod and would really screw up the proper action and just lead to it breaking again.
Good idea...I have an old rod which I loved, but got broken by a friend accidentally stepping on it. He bought me a new rod, although it's not the same as my old favourite. I might give this a go, although it may affect the action of it. Worth trying though. 👍
i had my carp rod break away the top section before the second eye down . this being carbon would it effect the casting abilty . i think when i put the rod away i think the lead hit the to section . my friends rod was sitting on his pod when an acorn hit his rod . we heard a noise . he went to cast a few minutes later and his carbon rod shattered . near the top .
Using a nail to fix a broken rod section will destroy the action of that rod, better to use a section of another broken rod epoxied in place to join the two pieces, epoxy is more flexible than superglue which will eventually break, you can also use a piece solid fiberglass from a quiver tip to repair sections that brake close to the top eye which are too narrow to fit a section of hollow rod inside.
@@alfredliggins8510 then you should just use an inch thick stick for a rod with some baler twine tied on the end for line, a bent safety pin for a hook and a chunk of roofing lead for a weight.
I have a rod my dad used for fishing called a Black Marlin, but it is a surf rod. It has a stainless steel inner, and the rod was created around that. It is about 9 to 11 feet, and I have caught everything and anything on it with an old Penn 49, from sharks to whatever you can think about around the South African coast line. I also have a shorter rod where I used a Penn 500 on, come to think of it I still have brand new one in a box, man did I love that 500, it could cast all the way to the horizon. I suppose you have all gathered I am an old timer, lol!!!
the materials that are used is standard super glue and nylon thread (fishing line). the lighter is supposed to shrink the thread hot air blower will do as well. good luck
just done a similar repair but was fortunate to have a few old bits of hollow carbon fibre so use a piece of that as it will flex. was that just a superglue you finished off the whippping with, im waiting on a 2 part epoxy
Идея правильная - воплощение никс. Внутрь по диаметру стеклопластиковый кусочек 5-6 см на клее супер-гель, выровнять соосность без спешки, клей позволяет. Сверху шину из полосок 1-1,5 мм ( с кусочка старой удочки), длинной 5-6 см на клею. Сверху бандаж из капроновой нитки, пропитать клеем 505 секунда (хорошо пропитывает).Все. Далее на вкус - клеем двухкомпонентным 5-ти минутка. Для красоты и аккуратности.
I use a 6 to 7 inch section of a. bicycle tire spoke. So much more effective and longer giving more support to the fractured area. My dad taught me this, decades ago.
Recently slammed my tailgate on my 9 ft salmon rod (G Loomis) broke 2 inches from the tip - ouch. Thought about just living w/ it but sent it in at my local Outdoor Pro shop. Ive bought 5 different G Loomis rods for trout, steelhead & kings in fresh & saltwater. G Loomis sent me a brand new Salmon mooching EX6. Charged me $12.00 for the shipping. Its a beauty too! You get what you pay for. ...Why they get my business.
Mantap om sangat membantu.. Dulu saya punya joran patah tp di buang aja karna gk bisa n gk tau gmn caranya 😁 Sekarang liat video ini jd nyesal saya knapa dulu di buang jorannya huhuu
wah sayang sekali om, padahal joran patah masih bisa di manfaatkan, masih ad beberapa tips lg memanfaatkan joran patah, nnti klo ada waktu lowong saya buat video nya 😁
Outstanding video! worked great! my fly rod is good as new after my wife put up the window on it. I used a brad, which I filed to a taper, and JB ClearWeld. Upholstery thread, black. Thank you, thank you.
That is basically what I do to repair a break but I use a fibreglass piece off another broken rod & glue in the break. I bind over it & then if the break is close to a runner I’ll remover the runner & bind the runner in place over the break. Been successful repairs from beach rod to small spinning rods. Curious as to what glue you use here. I’ve been using 24/hr Araldite. 👍🏻👍🏻🇦🇺
Скажу по своему опыты, металический стержень в нутри вершинки это абсурд вслучаии нагрузки он не гнется и вершинка ломается в местах окончания стержня.
Thanks a bunch. Just broke my favorite rod, hiking through heavy Forrest, and brush. I was crushed. Jumped on UA-cam, and found this simple fix. Even looks like good meditation. But can you tell us what kind of string you're using when you wrapped the black string around it, and heat shrink it? That'd be awesome.
You can use a small diameter cord, thread, braid... I recommend nano cord Paracord .75mm This stuff is strong and has a breaking strength of around 36lbs.
He’s not heat-shrinking, he’s just burning the fuzz off of the thread for a smoother finish when he puts the glue on. The other thread is just a different color.
Muito bom..estou com uma quebrada...pensei em fazer a mesma coisa...a diferença é que quebrou na parte mais baixa é grossa...mais o processo é o mesmo...valeu
Dude thank you so much this saved my g Loomis EX 6. My all time favorite rod. This is fucking genius and worked like a champ. I was ready to throw it in the trash because I couldn't claim it on my lifetime warranty cuz I slammed it in a door. Thanks again man a repair I will keep in my archived forever! Can't believe how many poles I have thrown out in the past that I could have saved easily. 🙏
I watched this video bc I broke my EX 6 lol. I loved it to, maybe it's a little to stiff in the tip and most of them break. I can't seem to find much about them online besides ppl saying theirs broke
Все понятно но есть одно но я бы вместо гвоздя вклеивал бы всё-таки графитовый полый стержень и не супер клей а на эпоксидную смолу , и начинал работу с вклеивания стержня со стороны комлевой части и после высыхания потом уже приступал непосредственно к кончику и соответственно поверх всего бандаж с нейлоновой нити с дальнейшим покрытием нитро лаком , а также с дальнейшей сушкой при небольшом вращении чтобы избежать потёков лака на очень малых оборотах пока не высохнет совсем . Хотя есть более современный способ ремонта графитовых удилищ , у меня как то я сломал спиннинг а именно кончик возле соединения шпигот , отослал по почте в Харьков тот что в Украине 🇺🇦 и мне ребята на танковом заводе им. Малышева срастили сломанный кончик на ультразвуковой сварке и отполировали место спайки что я присматривался так и не понял где было сломанное место , и спиннинг получился как только с конвейера , характеристики не поменялись звонкость и жесткость осталась прежняя , ловлю им 4 года и не заморачиваюсь как то так . Хотя идея автора видео тоже имеет право на жизнь за доступную идею я все равно ставлю Like и желаю Удачи и Ни Хвоста Ни Чешуи 🎣 🐟🐟🐟🐟🐟 👍👍👍👍👍.........
Во всем согласен.Кроме использования полого стержня.В последнее время для подобных ремонтов использую цельные стержни,для ул-графит,для л/м/х -стекло.Вес не особо большой,надежность же на порядки выше.С полой втулкой бывали казусы.Поломка на резкой подсечке,а до дома 100+ км.Все ловят,я гуляю ;-)
@@xanummannongprada7701 Приветствую да и такое тоже случается но все же гвоздь это не самый лучший вариант , а полый или цельный карбоновый штифт плотно подогнанный будет на порядок лучше удачи и ни хвоста ни чешуи 🎣👍......
И вам нхнч.Гвоздь ,это не "не вариант". Это полная дичь.Я использую цельный графитовый стержень.А в точке склейки стачиваю лак,и армирую углеволокном. Хотя с видео посмеялся.Покажу нашим " родбилдерам".Пусть учаться.Удачи вам,и уловов побольше.С ув .Николай
What was the product used to coat the whippings on the repair? I shall 3D print a joining piece from Nylon Carbon Fibre filament seeing as I have the 3D printer and the filament. That was a very nice repair and I am so glad I found your video, I broke a 1.75lb specimen rod about a year ago, it was a very expensive rod and so I was thinking of sending it to a professional rod builder for repair, this would have cot me around 70% of the rods cost, so a DIY repair will save me quite a bit of money.
Fishing Rod Strength Test After Repaired :
ua-cam.com/video/hS62WjzBrjU/v-deo.html
Ñ
@NORBERT LUKACS ㄱㄱ
Ч 3ешлббб
==)
1
@NORBERT LUKACS elimene
Sir I HAVE MAD RESPECT FOR YOU. I BROKE MY ROD TIP HEADING OUT THE DOOR FOR A TOURNAMENT THIS WEEKEND I COULD CRY. I SAW YOUR VIDEO AND WENT TO WORK. I HAD A MICRO ROD YOU KNOW REALLY THIN AT THE TOP. I GOT A SHAKEYHEAD HOOK THAT WOULD FIT CUT IT AND WENT TO WORK. I FEEL MUCH BETTER NOW. YOUR VIDEO SAVE MY HOME BECAUSE IT WAS GOING TO HELL TO TALK TO ME FROM NOW TO THE WEEKEND 😆 🤣 😂 😹 😆 SO GLAD GOD LEAD ME TO YOUR VIDEO AND TO NEVER GIVE UP. THANK YOU 😊 🙏 😊 🙏 😊
X 2
I used fiberglass sticks. They sell them in different sizes at Harbor Freight. $8 for a small pack. Worked perfectly with thread wraps and Epoxy. Now time to go test it out on some big Pike 😎🤙🏽
that is a very practical tip and solution TY
Я много лет занимаюсь ремонтом удилищ. Мой совет- ни в коем случае не пытайтесь отремонтировать бланк так, как показано здесь, колено будет в дальнейшем расщеплено в месте стыка. Внутреннюю вставку следует сделать из того же материала, что и удилище. Склеивание лучше выполнить эпоксидным клеем, супер клей , со временем становится хрупким и выкрашивается . После того как вы соединили поломанные части, нужно демонтировать кольца на бланке выше места перелома. Подобрать кусочек какого либо колена от удочки, которое плотно оденется на поломанное удилище в месте склейки. Достаточно трубки длинной 6-10 см.сажаем её на эпоксидку. По краям трубочки делаем нитяные бондажи и покрываем их эпоксидкой. Устанавливаем на место кольца. Ремонт окончен. Подмотку колец можно производить обычной ниткой, использовать для этого плетёнку нет смысла. Момент и подобные ему клеи для работ по ремонту удилищ не годятся.
Серьезно? Надо моему спиннингу об этом сказать, что уже 3 года работает, отремонтированный именно так. Видео не идеально. Супер-клей нужен хороший, гелевой консистенции, стержень дб обработан на концах (закруглен). Вместо нити, используем супер-клей + сода. Финальная обработка.
Спасибо.
Can I send mine to you to repair?
Тоже так себе технология. В Украине есть достаточное кол-во спецов по сращиванию графита, пользуюсь их услугами не один год...
_Solid metal placed in the rod can make the part on the rod connection stiff and easily broken due to strong pressure by the fish, i used a fiber stick from amazon for only 2 dollars for 100 cm_
Can you provide a link to it
Link of it ?
I don’t see it either
A steel from coil spring do the same, must be flexible and that is it . The glue must be also flexible . Technically speaking .
Thanks for the Intel
Thank you, when it was just a fishing rod, my heart broke, now it's easier, thank you brother
I was so upset when my new fly rod snapped today. This is is great! Beautiful video! Thank you
Never use a nail in a fly rod. You need to use carbon fibre with similar bending properties and a matching taper. The action will be affected and it will inevitably break otherwise.
Thanks - it works! I just repaired my 9' fly rod with a break in the first section. Had to find something thincker than a nail to fit but it seems to work well.
Hey what did you use that was thinner ? Having same problem
I was thinking a tooth pick maybe, gloe it and some really strong tape on the outside or something
This was ridiculously therapeutic haha. I really appreciate all of this!
I've fixed a couple of fly rod tips in a similar way. Since the rod is very narrow at the tip, a 2" sewing needle works well as the insert (you might need to clip off the eyelet). Sewing needles seem to have enough strength and stiffness, plus you can find one in a diameter that will fit snug enough. Alternatively, you can get loop end wire shafts from a lure making supply store which are made from stiff, springy steel (I used .035"). Also, you'll need to add at least 1 but preferably 2 sewing needles (or wire shafts) on the outside of the break as splints. Glue in the insert then wrap the splints and spread a thin layer of epoxy over the threads. I use dental floss because its strong and flat. Waxed or unwaxed floss works as long as you coat with epoxy. Put the splints on the sides of break and not along the top/bottom. This way there is less of a bump along the bottom where the fly line runs. I have mixed results as to whether the action and accuracy of the rod is affected with dry flies (I notice no issue with nymphs) but at minimum you can fish until you order a new tip and then you'll always have a backup tip.
You really saved me man i’m gonna do this
Vấn dề là ko đút lại đc đầu cần thôi... độ chắc bền thì ok
Thanks i snapped my rod tip and was stressing over it and then came upon this video and it worked
I’ve used a piece of another broken rod to insert as the splint between the broken pieces or have slid the broken pieces into the splint instead of using a nail. When gluing the pieces together with super glue, if you sprinkle baking soda into the wet super glue it will instantly set up as hard as a rock and fill the gaps between the rod pieces. I also use 2-part clear epoxy on the rod wrap threads instead of super glue. I have also shortened the rod until I got the lower section large enough for the broken tip section to slip inside it before gluing.
The glass/carbon fiber rods you´d normally use to build kites should work well, too.
The Baking Soda trick is amazing. Including, in model making.
Ро
I have several pieces of broken rods that I save to get a good fit with a taper like the rod I'm repairing . I use fine steel wool to ruff the rod before applying epoxy at the gap and to cover the thread . Great job ....looks like new ,and actually is stronger than new .
I do the same using rod repair thread and also just ordinary polyester sewing thread as well. I have bought carbide rod pieces at 1.5mm and hollow carbide tubes at 2.00 and 2.3 mm using them to make rod tip repairs. Turned out pretty good.
Permisi...Alhamdulillaah tetima kadih banyak kawan dudah berbagi Ilmu...semoga manfa,At .....suksrs selalu..👍👍🙏
Good Evening My Friend blueparay, Thank You for your detailed video on "How To Repair A Broken Fishing Rod." I to have experience a broken rod or two in my 35 year quest in fishing multiple spicese of fish! I to once implied the same techinque to repair a broken rod that a BEST FRIEND gave me. 🙂I Treasure the fact that YOU took the Time and EFFORT to Divise such a Detailed Video. Thank you once again my Fishing Friend for Being So Understanding and Compassionate for Our Sport of Fishing and the Millions of Viewers that watch Your Program! You are a TRUE Inspiration to US ALL!! 🙂MAY GOD "BLESS U & U'r Familiy! Sincerely, Mr. Carl Joseph Gwizdala aka "DESPERADO." 🙂
Just done this today. only thing I done different is put a coat of clear over the nylon and cured it under a uv light .Turned pretty nice glad to have my rod back .
Thank you for this. You’ve saved my old fly rod.
Cách sửa chữa cần bị gẩy rất hây cảm ơn bạn đả chia sẻ video cho những cần thủ có cần câu bị gẩy👍👍👍
Гвоздь это конечно круто!, долго не протянет, вместо гвоздя нужно(желательно) использовать гибкую вставку, например от сменных вершинок, живучесть повышается.
Сто пудов. При хорошей нагрузке поломка будет перед гвоздём. Не распределитсЯ нормально нагрузка на этом участке.
Задорнов был прав))))) и до задницы та нитка
Я вообще внутрь оправку из плотной бумаги, пропитанной быстросохнущей эпоксидкой, вставляю. А когда схватится - снаружи углетканью, опять же на эпоксидке, сверху приматыааб скотчем. Потом скотч срезаю, и зашлифовываю наждачкой. Получается незаметно, и крепко, и вес и строй практически сохраняется.
Снаружи трубку одевать надо.
@@ВасяВасильев-д9й внутрь ломик, снаружи канализационную трубу
Damn! I wish I saw this video about a 100 broken rod’s ago! Awesome! Thank you!
I'm the kind of person that sees value in everything. And I also get a sentimental value from things I repair. Today I broke a rod like an idiot and I really want to buy what I need to repair it.
Seeing this done with what I believe to be a watery cyanoacrylate, some thread and a metal is reassuring. Unfortunately my rod is in a bad way, it needs a guide and has two breaks in the tip. I think it's a little out of my hands because it broke in the first place because I tried to shortcut life and use a stone bench grinder to attempt to remove a broken guide, slightly scratching a little deep in the the rod creating a weak point where it snapped, and somehow snapped like 10cm down the rod in another spot. It's like my only decent rod too I'm so sad..
Saran aja ya mas
Setiap beli rood baru usahakan top
Rood lilit pe mulai dari bawah sambunggan hingga ring bagian atas sambungan (jika di hitung dari bawah no2) ini efektif buat rood yg bertipe holow.
Semoga bermanfaat
Biar tdak mudah patah y om
@@DyanSinchan iya om gak ada efek ama lengkungn ataupun beban di rood alias tidak ada efek samping sama x.
Tetapi berefek ama kekuatan saja meskipun sederhana tetapi saya buktikan dengan nahan tarikan baramundi dengan bobot 6kg tak ada dampak ama lengkungn nya om pokoknya kuat dah(rood jhoncoo 2.1m)
I've thoroughly enjoyed your knot tying videos!😊 I started building rods (Professionally), in mid 70s (I think 1976), and I don't mean building a fly rod, as those are ridiculously easy to put together!! I'm talking about boat rods with roller-guides and pack-rods (4 or 6 piece high quality rods), out of a 1 Piece Blank, meaning that I had to make my own ferrules!! And then I'd do anything from "perfect" Half & Half Diamond wraps that took 8 to 10 hours non stop!! By half and half, I mean half the Diamonds would be one color and the other half another. And many more like the U.S. flag with the stars and all, or Eagles etc. and it would take many wraps of thread to create. At any rate, the rod with the Nail would have one heck of Dead Section!! This of course would be no problem with even a Trophy Bass, but certainly not with a Big Steelhead or any fresh Chinook/King Salmon (fresh out of the Pacific Ocean)!! I still catch a good number of Kings going to 40 pounds or larger!! Again I can land any Bass with just about any rod or hand-line!! Someone else mentions the use of broken rod pieces, which makes a lot more sense!!
I'm wanting to make a 1 piece rod into a 3 piece and I was brainstorming ways to make it fit into itself, it's hard to find info online about it that I understand. Maybe you can link me a video to help. I was just wondering if using apoxy and peices of another blank to make a stopper for how far the peice will insert and using 20lb braid+apoxy to keep the blank from splitting out under load bc I'm going to need to do significant stock removal to the ID on the female end for the male end to fit. Is the male end filled with fiber/apoxy or is it just capped off. I have so many questions about how a broke 22 year old can make ferrules in his garage but I doubt you'll see my questions bc your comment is a year old , worth a try tho lol
great video. now if could just find the broken off tips.
Worked beautifully sir, even for an amateur like me! Thank you for sharing!
What kind of string did you use to do the wrap? Can I just go to my local sporting goods store, and they'll know what to sell me?
I just bought a rod online that showed up busted like this. I was going to just return it, but I think I'll consider it an investment in self sufficiency and just go ahead and figure out how to fix it instead. Thanks for the inspiration.
Great video, but you should list all the things you used for the repair and where to get it.
I ordered a fishing rod 3 months ago and it arrived yesterday.
A friend broke it today.
I cried for 4 hours.
So thank you very much.
Есть ещё проще вариант:вставку сделать не из гвоздя, а из стеклопластика( китайские дешёвые вершинки).
Гвоздь, как мне кажется, все-таки надежней - в этой части лучше, что бы изгиба больше не было вообще. Но, вот края гвоздя бы сделал максимально шаровидными, что бы не было места концентрации усилия об точечное место в виде заусеницы. А еще, неплохо бы, чтобы до и после гвоздя какой-нибудь наполни тель в виде герметика был.
@@andreykalita1205 в районе гвоздя (где он заканчивается) будет новая поломка. Я так пытался ремонтировать бамбуковые удочки, когда мне было 12 лет. После того, как подрос, понял, что необходима трубка снаружи.
It wasn’t an extra repair I wish I had seen earlier over the years thank you for posting that
I really wish I would have known this technique many years ago. After coming back from a bass fishing trip to Florida I was unloading my boat at home and my favorite rod had it's tap broken off buy the screen door closing too fast. I had tens if not even hundred of thousand cast on that rod. It was so old that they no longer made it so I could not replace it.
Sorry for your loss
RIP
Rest In Pieces
I know the feeling mate, I had the same thing happen only the door was timber.
@@mickpittman4244 Или дверь автомобиля, как у меня))
I hope it wasn’t a $400 rod, like the one I broke the top off of in 2 places, before I’d used it for a month! Or the $300 rod I broke in a car door a month later. Lessons learned!
I broke mine in a car door shortly after building it. It was the first fly rod I ever built. I came up with the same idea but I used epoxy at the time many years ago. Thanks
If needs must it’s a solid repair but it would create a flat spot in the blank and affect the action of it when put under strain. I cannot fault you for saving your rod though👍
Mantap boss... untung joran saya yg patah belum saya buang, nemu solusinya sekarang, terima kadih boss🤝🤝
Just had a rod tip break the other day and then found this. Providence! Easy to understand. thanks.
today my fishing rod was broken, it was very similar to the broken position like in the video, now I found this video as a solution, thank you very much
just bought a BNM super sensitive and broke first time I used it. will try to take it back but if not this is a super solution. will use epoxy instead of super glue
who hasn't found a discarded broken rod along the shore? I always gather the tip end to use sections as an insert instead of a nail. Strength is there plus the flex.
Better off with a piece of fiberglass or a bamboo it's better and gives more flexibility.
I thought that was a good way to fix the rod I think I bought one repaired tha way we will see how it works
Jetzt wird es wahrscheinlich unter den eingebauten Zapfen demnächst brechen......,aber schön gezeigt,Danke
Если уже таким способом ремонтировать то хотя бы для приличия края у гвоздя на наждаке закруглил бы ато острые углы при нагрузках со временем расколят стеклопластик а по нормальному надо бы стеклопластик пустотелый вставлять внутрь ИМХО :)
Если такой умный - покажи.
@@макардыня я вставлял кончик от зимней удочки подогнал по диаметру кончик из стеклопластика а так делать бы не стал
Эти иностранцы не имеют понятия про синюю изоленту - главный ремонтный материал в РФ.
Definitely going to try. My rod broke lower down on though but still I'm going to get it done. Thanks for the info
When my rod snapped my heart literally broke
i feel you bro
same it happened when I was taking algae off of the rod and then I heard the snap noise and a bunch of tension released form the line and the rod, I looked at my rod and a foot of the rod came off and I just thought "there is no way that just snapped my rod."
Brought my 4 year old with me to the river, used the same rod since I was 16, bought a new one for bobber and egg fishing for salmon nicest rod I've had a nice 9'6 okuma guide select pro $200 or so...stepped on 😔
Same 😔
i felt the same thing
Thanks its happened to me so many times and I would just trash it or in my boat getting snapped on brush going to a favorite spot and bam . Now I'll put this in my tackle box, thanks again.
I would personally use fiberglass then epoxy that in before wrapping, something as rigid as metal seems like a bad idea in a rod and would really screw up the proper action and just lead to it breaking again.
Very nice thank you for showing it on you tube have a nice day 😉
Good idea...I have an old rod which I loved, but got broken by a friend accidentally stepping on it. He bought me a new rod, although it's not the same as my old favourite.
I might give this a go, although it may affect the action of it.
Worth trying though. 👍
Try a solid fiberglass rod, should mess with the action less.
Елт
i had my carp rod break away the top section before the second eye down . this being carbon would it effect the casting abilty . i think when i put the rod away i think the lead hit the to section . my friends rod was sitting on his pod when an acorn hit his rod . we heard a noise . he went to cast a few minutes later and his carbon rod shattered . near the top .
Using a nail to fix a broken rod section will destroy the action of that rod, better to use a section of another broken rod epoxied in place to join the two pieces, epoxy is more flexible than superglue which will eventually break, you can also use a piece solid fiberglass from a quiver tip to repair sections that brake close to the top eye which are too narrow to fit a section of hollow rod inside.
What if we don't care about the action....
@@alfredliggins8510 then you should just use an inch thick stick for a rod with some baler twine tied on the end for line, a bent safety pin for a hook and a chunk of roofing lead for a weight.
Super 👌
From Azerbaijan Fishing 🐟👈
This is great but it would be nice to know the supplies used to fix it?
Nail, fly tying thread, CA glue 👍
i have 4 expensive rod to fix, was looking for solutions. its here, thanks
Также сделал, но вместо гвоздя вклеил кусок стеклопластика от старого удилища. Легче в 1,3 раза
и прям также намотал как в ролике?))
I have a rod my dad used for fishing called a Black Marlin, but it is a surf rod. It has a stainless steel inner, and the rod was created around that. It is about 9 to 11 feet, and I have caught everything and anything on it with an old Penn 49, from sharks to whatever you can think about around the South African coast line.
I also have a shorter rod where I used a Penn 500 on, come to think of it I still have brand new one in a box, man did I love that 500, it could cast all the way to the horizon. I suppose you have all gathered I am an old timer, lol!!!
the materials that are used is standard super glue and nylon thread (fishing line). the lighter is supposed to shrink the thread hot air blower will do as well. good luck
Actually the lighter is just to remove the fuzz on the thread that would impact the appearance of the finished repair.
This is a really good video. Very informative. Thank you
Hi, what Kind of yarn / filament did you use? cheers!
I see he didn’t answer you. I’m wondering the same as well as what that blue “string” was after the “thread.”
@@merlin80232 just use a 40lb braid or something similar
Blue string was just used to pull tag end of the original string through itself
just done a similar repair but was fortunate to have a few old bits of hollow carbon fibre so use a piece of that as it will flex. was that just a superglue you finished off the whippping with, im waiting on a 2 part epoxy
Идея правильная - воплощение никс. Внутрь по диаметру стеклопластиковый кусочек 5-6 см на клее супер-гель, выровнять соосность без спешки, клей позволяет. Сверху шину из полосок 1-1,5 мм ( с кусочка старой удочки), длинной 5-6 см на клею. Сверху бандаж из капроновой нитки, пропитать клеем 505 секунда (хорошо пропитывает).Все. Далее на вкус - клеем двухкомпонентным 5-ти минутка. Для красоты и аккуратности.
а почему внутрь не кусок карбона, подходящей конусности
Thanks for sharing this vedeo master..we have my rod is broken..
If you don't have any thread could you use heat shrink tubing?
Assalamualaikum mas broo dan mantap pengalamannya bisa di coba nampaknya kuat karna pakai besi dalamnya salam kenal dan salam sukses selalu 🙏🤣🙏
I use a 6 to 7 inch section of a. bicycle tire spoke. So much more effective and longer giving more support to the fractured area. My dad taught me this, decades ago.
makes a lot of sense thanks.
Hebat dan luar biasa Tutorial penyambungan jorannya yang kondisi patah, sukses selalu kawan 👍👍👍🙏
Going to watch this on repeat while I fix my fly rod. Thanks mate!
Top job, brilliant idea 👍🏼
what nylon and what glue is used, thanks good video
Super Glue, this glue from korea, but in my country called LEM G.
And the braid, just standart braid, maybe size 0,8 or 1
Recently slammed my tailgate on my 9 ft salmon rod (G Loomis) broke 2 inches from the tip - ouch. Thought about just living w/ it but sent it in at my local Outdoor Pro shop. Ive bought 5 different G Loomis rods for trout, steelhead & kings in fresh & saltwater. G Loomis sent me a brand new Salmon mooching EX6. Charged me $12.00 for the shipping. Its a beauty too! You get what you pay for. ...Why they get my business.
Mandou bem amigo
ja sei que tem jeito👏👏👏👏👍👍
Terima kasih bang ilmunya..🙏🙏🙏
Bom dia parabéns bela explicação uma ótima dica como restaurar uma vara de pesca
SERÁ QUE É SUPER BONDE?
Un mamarracho con algo rígido quiebra en otro lado
I did this on my pole and it worked great.
The rod whil always go break on the edge of nail, no matter of the glue,thread
or whatever
tomorow.. i ll make video strength test with this rod, hope you enjoy it 😁
@@blueparay I'm sure to look at it
Strength Test :
ua-cam.com/video/hS62WjzBrjU/v-deo.html
Ngeriiii
Are you still there morront?
Beautiful work sir !
That's cool I used the nail and different glue about 30 years ago but it works. Still have the rod! It sucks to break a $100+ rod and just let it go.
Excellent job very clear video thank you !
Muito bom, nunca é demais aprender novas técnicas pra arrumar uma vara de pescar 🎣
What kind of glue?
Mantap om sangat membantu.. Dulu saya punya joran patah tp di buang aja karna gk bisa n gk tau gmn caranya 😁
Sekarang liat video ini jd nyesal saya knapa dulu di buang jorannya huhuu
wah sayang sekali om, padahal joran patah masih bisa di manfaatkan, masih ad beberapa tips lg memanfaatkan joran patah, nnti klo ada waktu lowong saya buat video nya 😁
Strength Test :
ua-cam.com/video/hS62WjzBrjU/v-deo.html
Outstanding video! worked great! my fly rod is good as new after my wife put up the window on it. I used a brad, which I filed to a taper, and JB ClearWeld. Upholstery thread, black. Thank you, thank you.
Hebat x mas..terima kasih vidionya😃🙏
That is basically what I do to repair a break but I use a fibreglass piece off another broken rod & glue in the break. I bind over it & then if the break is close to a runner I’ll remover the runner & bind the runner in place over the break. Been successful repairs from beach rod to small spinning rods. Curious as to what glue you use here. I’ve been using 24/hr Araldite. 👍🏻👍🏻🇦🇺
He used CA glue which is what super glue is.
Скажу по своему опыты, металический стержень в нутри вершинки это абсурд вслучаии нагрузки он не гнется и вершинка ломается в местах окончания стержня.
Thanks a bunch. Just broke my favorite rod, hiking through heavy Forrest, and brush. I was crushed. Jumped on UA-cam, and found this simple fix. Even looks like good meditation.
But can you tell us what kind of string you're using when you wrapped the black string around it, and heat shrink it? That'd be awesome.
You can use a small diameter cord, thread, braid...
I recommend nano cord Paracord .75mm
This stuff is strong and has a breaking strength of around 36lbs.
Р
He’s not heat-shrinking, he’s just burning the fuzz off of the thread for a smoother finish when he puts the glue on. The other thread is just a different color.
Thank you for the video! Very helpful!
Muito bom..estou com uma quebrada...pensei em fazer a mesma coisa...a diferença é que quebrou na parte mais baixa é grossa...mais o processo é o mesmo...valeu
Was that super glue you used?. Usually it turns white when it sets.
Для начала надо научиться отличать удочку от спиннинга, а плоскогубцы не идут в сравнение с сопротивлением рыбы.
It's very nice, thank's for video 👍
Спасибо зам мастер клас, по ремонту училища🇷🇺🇷🇺🇷🇺
Assorted roll pins work awesome for fixes. What type of thread is he using? Must be a wax or plastic based thread that is shrinkable?
釘か…。
でも同じ要領で他の素材(釘より軽くテーパーやカーボンに馴染みそうな)を探せば、何かいいのがあるかも。
あとは愛情でカバー、だな。
Dapat menambah ilmu baru..terima kasih videonya
一点に力が集中するからすぐ折れるよ
あばらかずま 思った。
"Отличный ремонт"
После такого мне работы больше...
Gostei muito do truques, mais uma que eu a prendi, porque sou um pescador e gosto de coisas novas parabéns muito bom
Dude thank you so much this saved my g Loomis EX 6. My all time favorite rod. This is fucking genius and worked like a champ. I was ready to throw it in the trash because I couldn't claim it on my lifetime warranty cuz I slammed it in a door. Thanks again man a repair I will keep in my archived forever! Can't believe how many poles I have thrown out in the past that I could have saved easily. 🙏
I watched this video bc I broke my EX 6 lol. I loved it to, maybe it's a little to stiff in the tip and most of them break. I can't seem to find much about them online besides ppl saying theirs broke
@@brianallen1205 latest update it snapped again right above the nail repair.
@@RoscoeCletusArchie yea I'm expecting mine to break again. I'm going to make it a 3 peice travel rod pretty soon
@@brianallen1205 😂😂😂😂, I was able to cop a new replacement for 100 by my tackle shop.
@@RoscoeCletusArchie just had it happen to a 6 month old Loomis GCX hoping to fix it😂
Excelente, a minha qbrou. fiz a mesma coisa e está belezinha. Já peguei muitas tilápias.abrç..
SERÁ QUE É SUPER BONDE?
Ahh the song goes perfect with the video, song of hope ❤
Just got a custom made ultralight rod yesterday. $250. Tip got snapped by my kayak lid before I even got to use it once.
My condlolenciss I broke my favourite baitcasting rod a few days ago . After watching this a repair will be attempted without the nail .
What material is this black line? Nylon, braid or something else? thank you!
Все понятно но есть одно но я бы вместо гвоздя вклеивал бы всё-таки графитовый полый стержень и не супер клей а на эпоксидную смолу , и начинал работу с вклеивания стержня со стороны комлевой части и после высыхания потом уже приступал непосредственно к кончику и соответственно поверх всего бандаж с нейлоновой нити с дальнейшим покрытием нитро лаком , а также с дальнейшей сушкой при небольшом вращении чтобы избежать потёков лака на очень малых оборотах пока не высохнет совсем . Хотя есть более современный способ ремонта графитовых удилищ , у меня как то я сломал спиннинг а именно кончик возле соединения шпигот , отослал по почте в Харьков тот что в Украине 🇺🇦 и мне ребята на танковом заводе им. Малышева срастили сломанный кончик на ультразвуковой сварке и отполировали место спайки что я присматривался так и не понял где было сломанное место , и спиннинг получился как только с конвейера , характеристики не поменялись звонкость и жесткость осталась прежняя , ловлю им 4 года и не заморачиваюсь как то так . Хотя идея автора видео тоже имеет право на жизнь за доступную идею я все равно ставлю Like и желаю Удачи и Ни Хвоста Ни Чешуи 🎣 🐟🐟🐟🐟🐟 👍👍👍👍👍.........
Друган!!!!)))))Многие поняли твой комент!))))
Во всем согласен.Кроме использования полого стержня.В последнее время для подобных ремонтов использую цельные стержни,для ул-графит,для л/м/х -стекло.Вес не особо большой,надежность же на порядки выше.С полой втулкой бывали казусы.Поломка на резкой подсечке,а до дома 100+ км.Все ловят,я гуляю ;-)
@@xanummannongprada7701 Приветствую да и такое тоже случается но все же гвоздь это не самый лучший вариант , а полый или цельный карбоновый штифт плотно подогнанный будет на порядок лучше удачи и ни хвоста ни чешуи 🎣👍......
И вам нхнч.Гвоздь ,это не "не вариант". Это полная дичь.Я использую цельный графитовый стержень.А в точке склейки стачиваю лак,и армирую углеволокном.
Хотя с видео посмеялся.Покажу нашим " родбилдерам".Пусть учаться.Удачи вам,и уловов побольше.С ув .Николай
@@xanummannongprada7701 И вам удачи и хороших трофеев 🎣🐟🐟🐟🐟🐟👍......
Sangat bermanafaat, idea creatif...👍👍👍
What was the product used to coat the whippings on the repair?
I shall 3D print a joining piece from Nylon Carbon Fibre filament seeing as I have the 3D printer and the filament.
That was a very nice repair and I am so glad I found your video, I broke a 1.75lb specimen rod about a year ago, it was a very expensive rod and so I was thinking of sending it to a professional rod builder for repair, this would have cot me around 70% of the rods cost, so a DIY repair will save me quite a bit of money.