Thanks a million Peanut Butter Man, my old WRX was blinking right rapidly, it was driving me crazy. The 2011’s had tight wiring and connectors can be come partially unplugged apparently... so my car was in pieces and I was about to take it down to nuts and bolts chasing the rabbit down the hole. Then I came across your video. Cleaned the contacts and bingo, job done.... So glad I found your video! I am one of just a few drivers in Massachusetts using his blinkers because I am just so happy they work : ) Thanks Man!
Thanks for sharing this with me. Very helpful when you said corrosion I was like yes now this Man knows what he's talking about yes. Blessings and more Blessings
Thanks a lot. This happened on my passenger side. The socket and bulb wasn't even that dirty, just a tad of corrosion and that was it. Cleaned both and fixed it.
Thanks for the video, In my case all that was needed was to remove the bulb housing and put it back. Was about to buy the bulb and it started working when I put it together again!
I've never trid it but apparently yes you can: www.chemtronics.com/how-do-you-clean-corroded-contacts#:~:text=It%20can%20be%20difficult%20to,cleaning%2C%20such%20as%20baking%20soda.
might just be a burned out bulb in the front.. have you replaced bulb with new?? or swap bulb with the same size bulb from other side light.. spray i used was from radio shack, no longer available.. this is basically the same: www.walmart.com/ip/CRC-QD-Electronic-Cleaner-11-Wt-Oz/16817418?wmlspartner=wlpa&selectedSellerId=0&wl13=605&gclsrc=aw.ds&adid=2222222227716817418_117755028669_12420145346&wl0=&wl1=g&wl2=c&wl3=501107745824&wl4=pla-394283752452&wl5=9193272&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=local&wl12=16817418&veh=sem_LIA&gclsrc=aw.ds&gad_source=1&gclid=Cj0KCQjwrp-3BhDgARIsAEWJ6SzsDWSH2c7Zzbjd-R97AM3KOgtPi_eD8nesAwbl8t7A9KYwR-A9oZsaAtlrEALw_wcB
Man I've got a rapid turn signal, bulbs aren't burnt connections look good, no fuses are burnt out, and my turn signal and break light stopped working, quite confused rn
I had a similar situation but with my motorcycle…. i had just replaced the left turn signal bulb (two filament bulb, not LED) and it started blinking too fast, while all other bulbs were OK. I pulled out the new bulb again, turned it 180 degrees and installed it again. This time it worked just fine! Maybe it was a polarity issue 🤷♂️
I dont know if it matters with signal bulbs, but i would also shy away from touching the actual bulb because of oils on your hand. Idont know if thats still a thing, but you can never be to careful
I think that's just for halogen bulbs cause they burn so hot.. Low wattage signal bulbs much cooler so not an issue.. But yeah, it's easy not to touch bulb during install so better safe than sorry..
My headlight on drivers side will not turn on is their a wiring problem bc the other side works fine and switching them over too the drivers, they lights don’t turn on anymore? But my direction light stops blinking rapidly?
i am having that problem as well but my turn signal light is dim and blinking fast , all bulbs are good and all parts are clean, what else could it be?
What I used is no longer available due to Radio Shack going out of business.. Any auto parts store would have electrical contact cleaner such as this: www.amazon.com/CRC-05103-Electronic-Cleaner-11/dp/B000BXOGNI/ref=dp_prsubs_1?pd_rd_i=B000BXOGNI&psc=1
Check your hazard lights.. If they also light up but don't blink your hazard/flasher relay may be bad.. That relay is usually found in the fuse box located in the engine compartment.. Here's more info: www.autoblog.com/2016/01/19/symptoms-of-a-bad-or-failing-hazard-turn-signal-flasher/
This is the spray I used in the video it's made by Radio Shack but difficult to find: www.hobbytown.com/radioshack-6400148-radioshack-control-contact-cleaner-and-lubricant-rsh6400148/p788093.. This spray should work just as well: www.google.com/shopping/product/10890697071685306133?lsf=seller:8175035,store:8635513338877327108,lsfqd:0&prds=oid:14472860652016534060&q=electronics+cleaner&hl=en&ei=yGxCZMD1IfuwkvQP9taEmAw&sts=14&lsft=gclid:CjwKCAjw6IiiBhAOEiwALNqncYqSJnku44TQdTCU5R_uYYYLDJZU5fm8Lkaq8b3F3A1EXmDMu8zsQBoCQ4AQAvD_BwE,gclsrc:aw.ds
What part is the connection .Not the light bulb but the other one. I broke the connection while changing my headlights and now the new lightbulb can’t fit back in. So I need to replace the connection .
i put in brand new headlight on driver side an when i used turn signal noticed the arrow itself was moving faster an louder. the headlight doesn’t show any turn light in the front but the rear does, would this be same issue ?
@@tongo117 lmao my dad just texted me right now as i was replying to u he was the one that did it lol, he said it probably just doesn’t have the bulb that we can take it from the old one that’s what we had to do for the headlight bulb
The spray I used in the video was made by Radio Shack and is no longer available.. This should work just as well: www.google.com/shopping/product/10890697071685306133?lsf=seller:8175035,store:8635513338877327108,lsfqd:0&prds=oid:14472860652016534060&q=electronics+cleaner&hl=en&ei=yGxCZMD1IfuwkvQP9taEmAw&sts=14&lsft=gclid:CjwKCAjw6IiiBhAOEiwALNqncYqSJnku44TQdTCU5R_uYYYLDJZU5fm8Lkaq8b3F3A1EXmDMu8zsQBoCQ4AQAvD_BwE,gclsrc:aw.ds
Bulb shown in video is a dual action 1157 bulb.. Two filaments inside glass and two contacts on bottom (base) of bulb.. If you have the same 1157 bulb one filament could be burned out and one still good.. So yes, your problem could just be the bulb..
So I have a Honda dc5 or in America it’s called the Acura rsx, what my one does is that when the key is plugged into the car the passenger side front and rear indicator starts ticking fast without me even turning any indicators on. Any idea what the issue could be?
I installed LEDS on my ‘06 civic and now both front and rear signals blinking rapidly. I was told a resistor kit was needed. I didn’t try spraying the contacts in the socket yet but I do have some WD-40 in the shed. Do you think I need a resistor kit or should I just try cleaning and spraying the WD-40?
The WD40 won't hurt, and I have no experience with LED bulbs, but the little research I did points to the need for resistors.. www.diodedynamics.com/led-resistor-kit-pair.html
@@rld1278 look at the bulb, if it’s an LED then it’ll blink fast because it’s drawing less power from the battery which is telling the car that the bulb’s out. Hence why it blinks fast. LED or not, try changing the bulb and see if it’s blown or not. Hope that helped!
The spray I used in the video was made by Radio Shack and is no longer available.. This should work just as well: www.google.com/shopping/product/10890697071685306133?lsf=seller:8175035,store:8635513338877327108,lsfqd:0&prds=oid:14472860652016534060&q=electronics+cleaner&hl=en&ei=yGxCZMD1IfuwkvQP9taEmAw&sts=14&lsft=gclid:CjwKCAjw6IiiBhAOEiwALNqncYqSJnku44TQdTCU5R_uYYYLDJZU5fm8Lkaq8b3F3A1EXmDMu8zsQBoCQ4AQAvD_BwE,gclsrc:aw.ds
I'm going to try this tomorrow. My tail lights do many things. Left turn signal is fine but right does not work with headlights on. Emergency flashers don't work with headlights on. Bulbs are fine. I have six builds (3 on each side). If I remove one of the bulbs I gain a function like the right turn signal with headlights on. Any ideas?
Thanks pb man! Exactly my problem. Also nicely edited video, no no unnecessary time spent talking...
Glad to help.. Thanks for reply..
Thank You very much for taking time to post your video, it was indeeed corrosion on my 1997 Jetta, Take care!
Glad to have helped..
Thanks a million Peanut Butter Man, my old WRX was blinking right rapidly, it was driving me crazy. The 2011’s had tight wiring and connectors can be come partially unplugged apparently... so my car was in pieces and I was about to take it down to nuts and bolts chasing the rabbit down the hole. Then I came across your video. Cleaned the contacts and bingo, job done....
So glad I found your video! I am one of just a few drivers in Massachusetts using his blinkers because I am just so happy they work : )
Thanks Man!
You are welcome.. Thanks for reply..
Thanks for sharing this with me.
Very helpful when you said corrosion I was like yes now this Man knows what he's talking about yes.
Blessings and more Blessings
That's what I needed. Blinking driver's side turn signal with all lights working. Looking forward to try.
Thanks a lot. This happened on my passenger side. The socket and bulb wasn't even that dirty, just a tad of corrosion and that was it. Cleaned both and fixed it.
Glad to help.. Thanks for reply..
Thanks for this post!! I had no idea what was causing my fast blinking after replacing all the lamps with new ones. It was driving me crazy.
Thumbs up for just getting to the point. Thankyou😊
You are the bomb dude ❤I love you so much ❤️
Great video - have a lexus as well that does this sometimes.
thanks for sharing. i can now fix my turn signal
Thanks for making this video. Learned something new today. Thanks for your help 💛
Thanks for the video, In my case all that was needed was to remove the bulb housing and put it back. Was about to buy the bulb and it started working when I put it together again!
Glad to have helped.. Thanks for reply..
Haven’t tried it yet but your a godsend
I was sure that would be the problem! Thanks a lot.
Can you use white vinegar to get rid of the corrosion?
I've never trid it but apparently yes you can:
www.chemtronics.com/how-do-you-clean-corroded-contacts#:~:text=It%20can%20be%20difficult%20to,cleaning%2C%20such%20as%20baking%20soda.
What spray did you use? My signal is not working in the front back signal blinking fast
might just be a burned out bulb in the front.. have you replaced bulb with new?? or swap bulb with the same size bulb from other side light.. spray i used was from radio shack, no longer available.. this is basically the same: www.walmart.com/ip/CRC-QD-Electronic-Cleaner-11-Wt-Oz/16817418?wmlspartner=wlpa&selectedSellerId=0&wl13=605&gclsrc=aw.ds&adid=2222222227716817418_117755028669_12420145346&wl0=&wl1=g&wl2=c&wl3=501107745824&wl4=pla-394283752452&wl5=9193272&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=local&wl12=16817418&veh=sem_LIA&gclsrc=aw.ds&gad_source=1&gclid=Cj0KCQjwrp-3BhDgARIsAEWJ6SzsDWSH2c7Zzbjd-R97AM3KOgtPi_eD8nesAwbl8t7A9KYwR-A9oZsaAtlrEALw_wcB
Even if this isn’t my problem thank you. I’m trying this on my lunch break soon!
You are welcome.. Good luck..
gonna try this for my bulbs. Prolly a stupid question but does wd40 work like anti corrosion?
Some people say yes, some say no.. here's an example of no:www.goldwingfacts.com/threads/never-use-wd-40-for-electrical-connections.366596/
This video is a gem
Man I've got a rapid turn signal, bulbs aren't burnt connections look good, no fuses are burnt out, and my turn signal and break light stopped working, quite confused rn
Check your emergency/blinker relay?
I had a similar situation but with my motorcycle…. i had just replaced the left turn signal bulb (two filament bulb, not LED) and it started blinking too fast, while all other bulbs were OK. I pulled out the new bulb again, turned it 180 degrees and installed it again. This time it worked just fine! Maybe it was a polarity issue 🤷♂️
Avalanche 2003 kept fast-flashing after replacing the bulb. Any idea what to do next?
I dont know if it matters with signal bulbs, but i would also shy away from touching the actual bulb because of oils on your hand. Idont know if thats still a thing, but you can never be to careful
I think that's just for halogen bulbs cause they burn so hot.. Low wattage signal bulbs much cooler so not an issue.. But yeah, it's easy not to touch bulb during install so better safe than sorry..
Hoping this is my problem. Thanks for the video
Thanks straight and to the point.
My headlight on drivers side will not turn on is their a wiring problem bc the other side works fine and switching them over too the drivers, they lights don’t turn on anymore? But my direction light stops blinking rapidly?
This is happening to me all headlights signal drivers side out in front. And turn signal blinking fast. Sante fe. Any luck? Ty
i am having that problem as well but my turn signal light is dim and blinking fast , all bulbs are good and all parts are clean, what else could it be?
very good thank you!
Glad to help.. Thanks for reply..
Thank you…you help me resolve problem
Glad to have helped..
Wow! Perfect video man!
Last time i threw away a whole wiring harness and replaced it. Im gonna try this when i get home. Or else try to just replace the one socket
Helped me a lot thank you
You're welcome..
Pls tell me what spray you used
What I used is no longer available due to Radio Shack going out of business.. Any auto parts store would have electrical contact cleaner such as this:
www.amazon.com/CRC-05103-Electronic-Cleaner-11/dp/B000BXOGNI/ref=dp_prsubs_1?pd_rd_i=B000BXOGNI&psc=1
I have an issue with my civic where the blinker light is illuminated but doesn’t blink need help thanks in advance
Check your hazard lights.. If they also light up but don't blink your hazard/flasher relay may be bad.. That relay is usually found in the fuse box located in the engine compartment.. Here's more info: www.autoblog.com/2016/01/19/symptoms-of-a-bad-or-failing-hazard-turn-signal-flasher/
Thanks!
What the name of that spray? It is like dielectric grease but in a spray can?
This is the spray I used in the video it's made by Radio Shack but difficult to find: www.hobbytown.com/radioshack-6400148-radioshack-control-contact-cleaner-and-lubricant-rsh6400148/p788093.. This spray should work just as well: www.google.com/shopping/product/10890697071685306133?lsf=seller:8175035,store:8635513338877327108,lsfqd:0&prds=oid:14472860652016534060&q=electronics+cleaner&hl=en&ei=yGxCZMD1IfuwkvQP9taEmAw&sts=14&lsft=gclid:CjwKCAjw6IiiBhAOEiwALNqncYqSJnku44TQdTCU5R_uYYYLDJZU5fm8Lkaq8b3F3A1EXmDMu8zsQBoCQ4AQAvD_BwE,gclsrc:aw.ds
Great info. Thanks!
What part is the connection .Not the light bulb but the other one. I broke the connection while changing my headlights and now the new lightbulb can’t fit back in. So I need to replace the connection .
I would either take a picture of the part you need and go to a local dealership parts dept or check salvage yards..
What brand and name is that anti corrosive lubricant spray?
Radio Shack spray product. Anti-corrosion/lubricating. CRC brand also makes a similar product.
Thanks for your video.
You're Welcome..
What could be the problem if the bulb is sometimes working and sometimes not?
i put in brand new headlight on driver side an when i used turn signal noticed the arrow itself was moving faster an louder. the headlight doesn’t show any turn light in the front but the rear does, would this be same issue ?
possibly yes, it's likely either the driver's side front turn signal bulb is bad, loose in the socket or there's corrosion at the terminals..
@@tongo117 lmao my dad just texted me right now as i was replying to u he was the one that did it lol, he said it probably just doesn’t have the bulb that we can take it from the old one that’s what we had to do for the headlight bulb
What did you spray I can’t hear volume
The spray I used in the video was made by Radio Shack and is no longer available.. This should work just as well:
www.google.com/shopping/product/10890697071685306133?lsf=seller:8175035,store:8635513338877327108,lsfqd:0&prds=oid:14472860652016534060&q=electronics+cleaner&hl=en&ei=yGxCZMD1IfuwkvQP9taEmAw&sts=14&lsft=gclid:CjwKCAjw6IiiBhAOEiwALNqncYqSJnku44TQdTCU5R_uYYYLDJZU5fm8Lkaq8b3F3A1EXmDMu8zsQBoCQ4AQAvD_BwE,gclsrc:aw.ds
My taillights running bulb doesn’t work but when it break it still works, is it wiring problems or the bulb itself?
Bulb shown in video is a dual action 1157 bulb.. Two filaments inside glass and two contacts on bottom (base) of bulb.. If you have the same 1157 bulb one filament could be burned out and one still good.. So yes, your problem could just be the bulb..
mine is actually weird. The front passenger blinks fast and the back passenger bulb stays on but doesn't blink at all. I changed the relay also.
Quite the description
So I have a Honda dc5 or in America it’s called the Acura rsx, what my one does is that when the key is plugged into the car the passenger side front and rear indicator starts ticking fast without me even turning any indicators on. Any idea what the issue could be?
A guess but, bad turn signal relay possibly?? Relay would be located in one of your fuse panels.. Most likely the one in the engine compartment..
Good video,
Did the indicator start blinking at a normal speed? Or still blinking rapid?
Normal speed after cleaning..
Thanks
Glad to help.. Thanks for reply..
Thank you soooo much 😁😁😁
Yes sir.. Glad to help..
I installed LEDS on my ‘06 civic and now both front and rear signals blinking rapidly. I was told a resistor kit was needed. I didn’t try spraying the contacts in the socket yet but I do have some WD-40 in the shed. Do you think I need a resistor kit or should I just try cleaning and spraying the WD-40?
The WD40 won't hurt, and I have no experience with LED bulbs, but the little research I did points to the need for resistors.. www.diodedynamics.com/led-resistor-kit-pair.html
I have a Honda CR-V doing this. I got it used so I don't know if they out in led or not.cam this be fixed by putting in regular bulbs?
@@rld1278 look at the bulb, if it’s an LED then it’ll blink fast because it’s drawing less power from the battery which is telling the car that the bulb’s out. Hence why it blinks fast. LED or not, try changing the bulb and see if it’s blown or not. Hope that helped!
Should this work on a moped too?
A loose or corroded connection could cause this on any vehicle so yes, this may work on a moped..
I got a dim fast blinking indicator and it’s pissing me off
What's the actual name of the spray and where can I get it?
The spray I used in the video was made by Radio Shack and is no longer available.. This should work just as well:
www.google.com/shopping/product/10890697071685306133?lsf=seller:8175035,store:8635513338877327108,lsfqd:0&prds=oid:14472860652016534060&q=electronics+cleaner&hl=en&ei=yGxCZMD1IfuwkvQP9taEmAw&sts=14&lsft=gclid:CjwKCAjw6IiiBhAOEiwALNqncYqSJnku44TQdTCU5R_uYYYLDJZU5fm8Lkaq8b3F3A1EXmDMu8zsQBoCQ4AQAvD_BwE,gclsrc:aw.ds
I see this after I buy bulbs 💀😂 and realize it’s not the bulbs it’s this 💀💀💀
What kind of spray did u use?
This is what I used but I don't think it's available anymore.. www.radioshack.com/products/radioshack-control-contact-cleaner-and-lubricant
@@tongo117 thankyou! Will wd40 work?
@@deludedhybridseverywhere5326 Some people say yes, others say no:forum.allaboutcircuits.com/threads/wd-40-as-contact-cleaner.36407/
@@tongo117 thankyou
@@tongo117 thankyou!!!
I'm going to try this tomorrow. My tail lights do many things. Left turn signal is fine but right does not work with headlights on. Emergency flashers don't work with headlights on. Bulbs are fine. I have six builds (3 on each side). If I remove one of the bulbs I gain a function like the right turn signal with headlights on. Any ideas?
What do you mean by "six builds?"
@@ApartmentKing66 what do you mean what do I mean because there’s no shortage of clues here that I’m talking about tail light bulbs.
I'm having the same issue where you able to figure out your problem, mine is driving me crazy. TIA
@@FutureRNTC I changed the whole tail light assembly.
Front driver blinks back driver nothing..changed bulb..still nothing no light or blink 😣 help please
Huge cat!
Yes.. His name was actually Big Man may he RIP..
You are touching your light bulbs, I thought you were not suposed to sir??
Well... that was the bulb. Now tell me what to do when it's not the bulb.
i did not replace the bulb it was good.. connection was bad
Oh that's why it's doing that. Fuuuuuun.
Put rust penetration lube on them bolts most bolts are rusted then let it sit a while gently go back a forth on the bolt till it come out
Can you use wd40?
Yes, WD40 would probably work.. What I used in the video was from Radio Shack which has gone out of business..
I just wiggled the wires and it started working
Sometimes that's all it takes..
Mine fixed its self lmao
Bro don't handle that bulb with your bare hands....
Don’t handle bulb with bare hands. Skin oil shortens bulb life
Lol. Is that right