The only video on the internet that deals with this problem. Thanks so much ! I searched for quite some time to finally reach your video. Great help ! Thank you !!!!👍👍👍🇷🇴
Thank you. Here's another video I found for other F series. ua-cam.com/video/F9BUsgURb-Y/v-deo.html This is a simpler fix than what I had to go through on the X3. Now there's 2 videos on the internet!
@@manip7462 so far so good. When I melted the burnt part away it created a little more room between the tube and the LED....a little more "cooling" room. The LED is so bright that a little more space didn't make a difference in brightness.
Just a quick tip for the burnt angel eye plastic. Had the same problem on my LCI E70 when the led burned out and made the light yellow. Use a dremel to shave away the brown burnt plastic. Then you are left with a clear surface but its cloudy and the light doesnt shine through that good, to solve that use furniture varnish or some kind of a clear coat. Makes the plastic see through again. Worked perfectly for me.
Hi, i have exactly this problem, sanded down the brown dot, but the tip of the plastic still cloudy, can you be more specific on the furniture varnish, i have a 3 in 1 red oil for furniture, would that help?
@@Lurigobo No use something that doesnt stain. Best to use something that leaves a clear surface (like clear coat on car paint) and creates like a layer to smooth out the part you sanded or used the dremel on.
@@FireCrackerEST Thank you for the response, i used a clear epoxy and it worked great, the cloudy surface went away and the change was great!! Appreciate you’re comment
For those attempting the repair, I used a 6 inch long 7/64" drill bit (3$ from amazon) to remove the burnt plastic. Drilled it out by hand 2-3 millimiters deep, installed the new led driver and the result is perfect. Simplest way to do it in my opinion.
Like I mentioned in one of my responses; it's still very white because it's so bright. And I would expect it to go yellow again but not for years. The small amount of material removed may actually help it last longer as it's not as close to the heat source.
Also to note in hot countries the drl can still be bright but yellow. It’s uv damage to the ring itself, clear or white plastic will turn yellow in hot climates
Thank you very much for your video. I just changed the module without changing the ring and it improved by 70-80%. Of course cleaning the ring would be perfect but i didnt have the tools. Thanks again
Thank you for your video. Helped me fix a yellow drl I had on my X4 F26. Luckily mine was the driver side one over the D1s bulb. So I only had to drill one hole and then seal it with silicone. Regardless, now the DRLs look as they should
Thanks a lot for all the information you shared in this video which gives completed idea how to fix it, as I was wrong before, looking for a LED driver for simpe replacement (like you at the beginning). Good job.
This is a great video. Better than BMW could’ve explained it. I just don’t know why they don’t have a recall for this. It’s very common on lots of beamers and for us to pay $3000 bc I tiny little LED light that burns out over time? We as customers of these vehicles deserve to have BMW replace these under factory defect. From watching this whole video you did, I’d rather not go through the hassle with fixing it with replacing them with used transmitters that could eventually go bad anyway again.
My bmw is a f22 (nearly 9 years old) and never experienced any issues but my moms 2017 X1 recently got this problem along with many others too much to list. Had turned off the daytime running lights only during the day so it wouldn’t look bad for now. Saw others in my area where both sides had this problem, even a x3 with 1 ring completely off while other 3 still on
Nice video. There's also some nice plastic welding tools available from China these days for only about $30 ea. One suggestion - please update your title with the chassis code (F25?)
Thanks. That was also my approach. I'm a pretty experienced coder and no matter what value I set it at... I saw no difference. Even when I tried on my 4 series. If you can get it to work, please post back. I really don't need my DRL that bright either!
Its been 1.5 years since you did the modification, any issues with the holes that you made? Did any moisture went in the headlight or any other issues?
Hi mate After about a year of problems I finally found your video. My problem is my driver side the drl have completely stopped working. Like you I thought it was the old ballasts with the red rings nobody understands the lci have the ballasts inside. Tp be honest I ddnt know until your video. No wonder bmw say it's a sealed unit and to replace the entire thing. You reckon as my drl don't work at all it's gonna be the same thing? Just need to purchase the led modules? Headlights, beams and indicators all work fine
Most likely you simply have a dead module. The module in my video drives the LEDs and not the halogen headlight. So, the HID ballast probably isn't involved. My guess is it's the module itself that's cooked.
@@vinfogarage1546 thanks for the response mate. So i had a brainwave moment and decided to just double check again. after a year of driving with no angel DRLs on the driviers side - i put my hand in and the wire connection for the module is dislodged! it just came out on my hand. I still have to take apart the bumper and unscrew just to get the wire connection in so im gonna give it a try this weekend before buying any parts. Just seems like a loose wire connection!
The halo "bulb" is actually the light module with the LEDs. The halo tips push up against the hot LEDs and eventually burns brown. That brown light reflects through the halo giving it that yellow look. To replace just the halo, you would need to buy a new light assembly for a lot of $$$. You can't just replace that halo part. Best to clean it. My melting worked but was messy and I would've used a dremel if I could fit it in.
@@vinfogarage1546 I have/had this same problem on my X3. I just changed out the module myself last month. Did all the steps of clearing out the light tube of burnt yellow (I used a dremel) and changed out the module. Then a month later, the yellowing came back so my assumption is that I didn't get enough of the yellow out the first time. I may have to get back in there and use the drill bit method you suggested. I would have rather just tried to change out the light tube but that seems like a pain in the ass since it's within the assembly and probably something I can't do without just changing out the entire headlight huh?
Yes. You'll need to recode the VO (vehicle order) and other parameters in the lighting module through ESYS so the car is aware of the change...not to mention the hardware/wiring changes. Probably a video somewhere showing the process.
hi .. are you using solder to clean the burn mark ? i got the same problem on bmw f10.. is it save using solder? melt it? iam affraid to use solder the heat could make it worse burn mark?
No solder. Just heat from the tip to break up the burn mark and scoop out the material. A better solution would be to polish the burn off with a dremil tool attachment listed below. The F10 may have easier access. If I were to do it again... I would try lightly grinding the burn off first. But I'm still satisfied with my results. www.amazon.com/dp/B094R4FGPQ/ref=cm_sw_r_apan_i_NBJFRQVK94NMX4PF73VJ?_encoding=UTF8&psc=1
Will i be able to code the daytime lights out, i just got my x4 and i have the same head lights my angel eyes are fine. But i rather have them off, hate seeing them on in the morning.
That's typically an easy setting in your iDrive system. Just turn Daytime Runnings Lights OFF under Lighting category. And they'll only come on with the headlights. No coding necessary.
@VinfoGarage mines a 2016 but for some reason under the light setting on the idrive it, doesnt have the option to turn it off... My e92 had that turn off function. But for some reason this x4 doesnt.
Interesting... my friend had a '16 X4.... great car. I also have a e92 and f36. Both have the option. I don't think I ever saw a current day Bimmer without the option under Vehicle Settings / Lighting. However, if it's not there... it could definitely be coded through ESYS.
BMW should be forced to replace all our headlights with the yellow DRL. I have the adaptive LED with one yellow ring and these fools actually say I have to replace the entire headlight $2400. Horrible designs I'm pretty sure they tested these headlights and know they were prone to yellowing yet they still design them with the control module inside the housing with no access to changing them.
Yea...The bright LED is a cool look but it comes with a price I guess. I see Audi and other manufacturers have the same issue. I was determined to find a fix... or at least try giving the cost of replacing it. Nothing to lose. I tried to code the voltage lower but it had no effect.
I m having the same x3 year 2015, LCI. MILEAGE only 86k KM. One turned yellowish now, meaning one driver/module gone? How many holes to drill in order to replace the driver? No easy way out and have to remove bumper? Do you have a simplified image to show which location to drill and cut ?
I also found a brand Sinolyn which comes with a better nicer ring x4,plus ballast and DTM daylight. One set. Do u think is better option since it’s better to change all 4 modules/driver instead of one Bcos the cost only slightly higher Vs changing all 4 driver.
Yellow means its burnt. The yellow color is reflecting the burn. Even if you change the module, you might have to scrape/clean the light tube... its probably burnt too. You need to remove the bumper because the headlights are mounted below the top of the bumper. I tried to go in through the wheel well but wasn't really working. If you get the headlight assembly out and look at my video, you should be able find how to get access. I did it kinda messy because i never saw someone do it before. Sorry I don't have additional pics.
The only video on the internet that deals with this problem. Thanks so much ! I searched for quite some time to finally reach your video. Great help ! Thank you !!!!👍👍👍🇷🇴
Thank you. Here's another video I found for other F series. ua-cam.com/video/F9BUsgURb-Y/v-deo.html
This is a simpler fix than what I had to go through on the X3. Now there's 2 videos on the internet!
@@vinfogarage1546 thanks! For the non LCI (2010-2014) there is another one : ua-cam.com/video/9komrVbhnx8/v-deo.html
Did the repair last? Did the light tubes melted again ?
@@manip7462 so far so good. When I melted the burnt part away it created a little more room between the tube and the LED....a little more "cooling" room. The LED is so bright that a little more space didn't make a difference in brightness.
Just a quick tip for the burnt angel eye plastic. Had the same problem on my LCI E70 when the led burned out and made the light yellow. Use a dremel to shave away the brown burnt plastic. Then you are left with a clear surface but its cloudy and the light doesnt shine through that good, to solve that use furniture varnish or some kind of a clear coat. Makes the plastic see through again. Worked perfectly for me.
Hi, i have exactly this problem, sanded down the brown dot, but the tip of the plastic still cloudy, can you be more specific on the furniture varnish, i have a 3 in 1 red oil for furniture, would that help?
@@Lurigobo No use something that doesnt stain. Best to use something that leaves a clear surface (like clear coat on car paint) and creates like a layer to smooth out the part you sanded or used the dremel on.
@@FireCrackerEST Thank you for the response, i used a clear epoxy and it worked great, the cloudy surface went away and the change was great!! Appreciate you’re comment
Tks. Will try epoxy clear since I do hv some leftover
How to use clear epoxy. I dont have any but i will order some. What do you do with it ? Do u just put it on ? Or is there a process to
It?
For those attempting the repair, I used a 6 inch long 7/64" drill bit (3$ from amazon) to remove the burnt plastic. Drilled it out by hand 2-3 millimiters deep, installed the new led driver and the result is perfect. Simplest way to do it in my opinion.
Nice. As I mentioned before. I wish I dremeled/drilled it or shaved it somehow. Melting was messy but effective.
Where did you bought the new driver Oem?
Hi is the DRL still remain white after u drill the burnt plastic. ? Or will it chg to yellowish again after few months.
Like I mentioned in one of my responses; it's still very white because it's so bright. And I would expect it to go yellow again but not for years. The small amount of material removed may actually help it last longer as it's not as close to the heat source.
@@mubull so far so good
Also to note in hot countries the drl can still be bright but yellow. It’s uv damage to the ring itself, clear or white plastic will turn yellow in hot climates
That was great 👍
Thank you very much for your video. I just changed the module without changing the ring and it improved by 70-80%. Of course cleaning the ring would be perfect but i didnt have the tools. Thanks again
Thank you for your video. Helped me fix a yellow drl I had on my X4 F26. Luckily mine was the driver side one over the D1s bulb. So I only had to drill one hole and then seal it with silicone. Regardless, now the DRLs look as they should
Thanks a lot for all the information you shared in this video which gives completed idea how to fix it, as I was wrong before, looking for a LED driver for simpe replacement (like you at the beginning). Good job.
This is a great video. Better than BMW could’ve explained it. I just don’t know why they don’t have a recall for this. It’s very common on lots of beamers and for us to pay $3000 bc I tiny little LED light that burns out over time? We as customers of these vehicles deserve to have BMW replace these under factory defect. From watching this whole video you did, I’d rather not go through the hassle with fixing it with replacing them with used transmitters that could eventually go bad anyway again.
Same problem- thanks for posting. Helped a lot.
The must usefull video I have seen. Thank you!
I have a 4 series with adaptive led and would like to just replace bulb. do you know where i can find
My bmw is a f22 (nearly 9 years old) and never experienced any issues but my moms 2017 X1 recently got this problem along with many others too much to list. Had turned off the daytime running lights only during the day so it wouldn’t look bad for now. Saw others in my area where both sides had this problem, even a x3 with 1 ring completely off while other 3 still on
Nice video. There's also some nice plastic welding tools available from China these days for only about $30 ea.
One suggestion - please update your title with the chassis code (F25?)
i wonder if it will happen to the other side of the angel eye probably drilling all other 3 to prevent the led from burning into it
Thanks for the Video. I will be doing this on my 2016 F25 LCI. ****I will also code the angel eye brightness to 80% so, it wouldn't happen again.
Thanks. That was also my approach. I'm a pretty experienced coder and no matter what value I set it at... I saw no difference. Even when I tried on my 4 series. If you can get it to work, please post back. I really don't need my DRL that bright either!
Thanks for sharing - big help
If I ship you my headlight would you be open to repair it?
Its been 1.5 years since you did the modification, any issues with the holes that you made? Did any moisture went in the headlight or any other issues?
I traded the car in for a 435 about a year after this. But I washed it like 40x a day and never saw any moisture. I was careful to seal it well.
Hi mate
After about a year of problems I finally found your video. My problem is my driver side the drl have completely stopped working. Like you I thought it was the old ballasts with the red rings nobody understands the lci have the ballasts inside. Tp be honest I ddnt know until your video. No wonder bmw say it's a sealed unit and to replace the entire thing. You reckon as my drl don't work at all it's gonna be the same thing? Just need to purchase the led modules?
Headlights, beams and indicators all work fine
Most likely you simply have a dead module. The module in my video drives the LEDs and not the halogen headlight. So, the HID ballast probably isn't involved. My guess is it's the module itself that's cooked.
@@vinfogarage1546 thanks for the response mate. So i had a brainwave moment and decided to just double check again. after a year of driving with no angel DRLs on the driviers side - i put my hand in and the wire connection for the module is dislodged! it just came out on my hand. I still have to take apart the bumper and unscrew just to get the wire connection in so im gonna give it a try this weekend before buying any parts. Just seems like a loose wire connection!
What about just changing out the Halo bulb with new will that work for the yellowing or do you still have to do all that with the cleaning
The halo "bulb" is actually the light module with the LEDs. The halo tips push up against the hot LEDs and eventually burns brown. That brown light reflects through the halo giving it that yellow look. To replace just the halo, you would need to buy a new light assembly for a lot of $$$. You can't just replace that halo part. Best to clean it. My melting worked but was messy and I would've used a dremel if I could fit it in.
@@vinfogarage1546 I have/had this same problem on my X3. I just changed out the module myself last month. Did all the steps of clearing out the light tube of burnt yellow (I used a dremel) and changed out the module. Then a month later, the yellowing came back so my assumption is that I didn't get enough of the yellow out the first time. I may have to get back in there and use the drill bit method you suggested. I would have rather just tried to change out the light tube but that seems like a pain in the ass since it's within the assembly and probably something I can't do without just changing out the entire headlight huh?
Thanks Broer.
Can you share link please where to get modules,my only one ring starts to yellowing so maybe just enough one module.thanks
Sure.... the link is in the video description under LED modules/drivers
i got the x3 with halogen, would you happen to know if i could just buy the xenon’s and replace them, would i need to code them in?
Yes. You'll need to recode the VO (vehicle order) and other parameters in the lighting module through ESYS so the car is aware of the change...not to mention the hardware/wiring changes. Probably a video somewhere showing the process.
hi .. are you using solder to clean the burn mark ?
i got the same problem on bmw f10..
is it save using solder? melt it?
iam affraid to use solder the heat could make it worse burn mark?
No solder. Just heat from the tip to break up the burn mark and scoop out the material. A better solution would be to polish the burn off with a dremil tool attachment listed below. The F10 may have easier access. If I were to do it again... I would try lightly grinding the burn off first. But I'm still satisfied with my results.
www.amazon.com/dp/B094R4FGPQ/ref=cm_sw_r_apan_i_NBJFRQVK94NMX4PF73VJ?_encoding=UTF8&psc=1
Did you have to do any coding after reinstalling headlights? Nice vid by the way!
Thank you sir. No coding needed. You might get an error code if the car ignition is on and headlight disconnected. But no coding.
Will i be able to code the daytime lights out, i just got my x4 and i have the same head lights my angel eyes are fine. But i rather have them off, hate seeing them on in the morning.
That's typically an easy setting in your iDrive system. Just turn Daytime Runnings Lights OFF under Lighting category. And they'll only come on with the headlights. No coding necessary.
@VinfoGarage mines a 2016 but for some reason under the light setting on the idrive it, doesnt have the option to turn it off...
My e92 had that turn off function. But for some reason this x4 doesnt.
Interesting... my friend had a '16 X4.... great car. I also have a e92 and f36. Both have the option. I don't think I ever saw a current day Bimmer without the option under Vehicle Settings / Lighting. However, if it's not there... it could definitely be coded through ESYS.
Awesome job , to bad you can’t change it separately as a official option
BMW should be forced to replace all our headlights with the yellow DRL. I have the adaptive LED with one yellow ring and these fools actually say I have to replace the entire headlight $2400. Horrible designs I'm pretty sure they tested these headlights and know they were prone to yellowing yet they still design them with the control module inside the housing with no access to changing them.
Yea...The bright LED is a cool look but it comes with a price I guess. I see Audi and other manufacturers have the same issue. I was determined to find a fix... or at least try giving the cost of replacing it. Nothing to lose. I tried to code the voltage lower but it had no effect.
I m having the same x3 year 2015, LCI. MILEAGE only 86k KM. One turned yellowish now, meaning one driver/module gone? How many holes to drill in order to replace the driver? No easy way out and have to remove bumper? Do you have a simplified image to show which location to drill and cut ?
I also found a brand Sinolyn which comes with a better nicer ring x4,plus ballast and DTM daylight. One set. Do u think is better option since it’s better to change all 4 modules/driver instead of one Bcos the cost only slightly higher Vs changing all 4 driver.
Yellow means its burnt. The yellow color is reflecting the burn. Even if you change the module, you might have to scrape/clean the light tube... its probably burnt too.
You need to remove the bumper because the headlights are mounted below the top of the bumper. I tried to go in through the wheel well but wasn't really working.
If you get the headlight assembly out and look at my video, you should be able find how to get access. I did it kinda messy because i never saw someone do it before. Sorry I don't have additional pics.
Not familiar with that product. I try to stay away from after market add ons. You might run into quality issues and throwing codes.
You are a brave 1...
Where can I find the this place
Uggh I regret buying a freakin BMW the bullshit you gotta deal with!!!
X12015