Sounds perfect to me mine is open headers and is way louder but once your ears bleed it’s not as loud anymore. Thank you for all the videos the older ones helped a ton and how to find a build sheet glad it was there proved it was a big block ss car. thank you
I have a 74 Nova that I converted the front and rear on and I call it Frankenstein too LOL, I installed electric cutouts on mine though. Its the best of both worlds...Trust me.
The 3 inch Exhaust is the Best thing You can do for a Big block, I have had a 3 inch on my 67 Chevelle for 20 years and still in new Condition, I have a 468 with 671 Blower, I Ported my 69 corvette Heads 435 hp I open the Exhaust side up a 1/4 inch match Gasket The 3 inch made it all come together, I have wrap around Hooker Headers. 700hp 695 ft pounds but the Exhaust is what made it work Best. KEEP it On Car
I have a set of ten inch rims and tires I put under each tire...gives you about that height and way safer than jack stand.... The way I always worked on my ol Novas... When not around the lift at the shop.
I had that same exhaust system in 2 1/2 on my Nova and it worked very well with the hooker headers. I'm going to be installing Doug's headers and they exit closer to the frame rails and was able to run pretty much straight pipe from the headers to the offset center borlas
I’ve got some magnaflow straight through mufflers on my 76 Corvette sbc and it sounds great. Not too loud. Aluminum heads and shorty headers. 2.5” exhaust if I remember right.
Sounds awesome I put 3” On my 74 ss with super 40s the front is offset in and rear center out with the original style tail pipes that are short and just turn down behind the rear tires where the original hangers are , it sounds amazing my engine is that 355 4 speed stick with 3:08 posi gears 1 7/8 Headers’s cause my first gear in my 4 speed Is that 3:11 first gear trans that’s why I need the 3:08 it’s in
I bought a set of borla straight through offset center. I have not cranked the car yet but I picked them because most people on UA-cam said they were too quiet. They're also really not that expensive compared to their late model specific fit mufflers
3" was a real tricky deal on my 68 4door .. 230 I-6 stock from about parking break wire.. a mere 100 trips to the store and 600 man hours under the car.. but it was worth it.
That’s a very wicked sounding lope that that cam has. Enough to scare away a lot of contenders😮. The volume is turned up a little loud but it sure sounds good just like that. 👊😮👍
@@Shop209 yea, I wasn’t real clear about what I was saying. I was trying to say that the tailpipe volume was loud like I like it but you might get a ticket. Love the sound.
I installed a pair of 19.0 inch Dynomax Bullet Resonators 10.0 inches off my big block headers then a pair of Borla XR-1 straight through exhaust mufflers size 3.0 inch x 17.0 inch stopped the mufflers shy of the posi-rear-end, muffler center inline with outer axle weld of the rear end spaced and level, zero drone inside... around 5,000 miles the mufflers should have a deeper growl. Extremely happy, you might try the Borla XS-1 off set... they sound nice on a camaro believe he's in Florida. He's very happy as well.
3 inch is loud. Especially when running straight thru's. I have dual 3 Flowmasters on my FrankenVega, with electric cutouts. So with a flick of a switch, I can go open headers. It took a lot of cutting fitting and welding, but it's well worth it. You can hear the difference at 1:07 into this video. ua-cam.com/video/Tbdxlht-DxI/v-deo.htmlsi=N8UruahKGCYrQegC
@@Shop209 Thanks Much! Do it! You'll love the convenience. I Built mine so it goes straight into the cutouts and branches off to the mufflers, so you get full open headers. I have to check out more of your channel. Keep up the good work.
Any way you can do a video on how to center a stubborn Steering wheel? I pulled my wheel off when I got it to find out it's splined so it's not as simple as pulling it off and putting it back on. Nova sounds great even if it's too loud. :)
Since you got onto the topic of exhaust, I'm curious what would be better to lower backpressure? Single *90 out in front of the back tires, or a *45 off the muffler, towards the tire, then another*45 with a pipe coming straight out? Also, may want to look at offset exit mufflers if you are having rear clearance issues. It's been a LONG time since I was part shopping, but I think flowmaster has some.
cut up some sidewall off a tire and make hangars with it.. yup straps around pipe like gutter straps or sportbike can strap then a washer and self tapper right into frame whatever, sounds perfect to me . . .
@@Shop209 my oldest brother lives in Thomasville, near Tallahassee, me and him saw Dave Mason live on leap day night and went to the famous spook bridge in quitman, close to Valdosta
@@Shop209those oval dynomax mufflers will quiet it down quite a bit more..that's what I've got on mine (74 nova, 358...465/465 cam..187x heads)( dynomax 3" offset inlet, center outlet) you can flip them either way cuz it's just straight through anyways..and 3 inch exhaust. I've also got an x pipe. Get one and it'll quiet it down even more.
Hey, sorry to be off topic but I need to know about the bumper tucks. Is there a video on it? A muffler shop owner told me I had to give the passenger and fuel tank area (ob) a wide berth. With an exhaust like that, why would you want a radio? Straight thru and not too loud are usually mutually exclusive.
If it's to loud you're to old and I say that was to loud because I am to old.😁 The best thing about electric cars is how they sound, everything else about them sucks but they do sound good.🤔 Ya know, I went from a 2" dual exhaust with Cherry Bombs with rams horn exhaust manifolds to a 2.5" X-pipe system with 1 5/8" headers on my sbc 383 and my car ran the exact QM times before the new system.🤔😯😡 And the Cherry B setup sounded better IMHO.🤨 Both systems sounded similar in the loudness level but the CB had a deeper note. I ordered the new system with turbo style mufflers that aren't annoyingly loud but still sounds like there's something under the hood that has some power when you step on the throttle. It exits out the back and with the windows rolled up, don't hardly notice it cruising in overdrive.😎👍
I think it sounds great if it was out the back ! Why not an out back exit with dumps ? Pre muffler( lol ) So much resonating with underneath exit as far as drivability. And no other vehicle has ever had that same exit as a Nova. All the N.O.V.A.’s as far as I remember. Take care bud
My shock relocation makes the tailpipes pretty hard to install without hitting. I love the way it sounds but it’s just too loud. Gonna go to a different Dyno max muffler.
Hi John. Question that I'm hoping u know. I have 70 4 door will a 2 Dr windshield trim fit on the 4 door? I need the passenger lower piece. Any info would be appreciated.
@@Shop209 Right, Where I live in Florida now I do alot of driving up and down U.S. to get to work and to cars and coffee's/cruise-ins/shows so I don't want all that crazy noise.
I don't know what happened but my car started running real bad. Went to change the plugs and gas shot out of 5 of my cylinders. What happened. Thank you
@@Shop209 while I was driving. If I let it set a couple of days it might not run bad but on the other hand it might not make any difference. I change carbs and it still acts like this.
That's illegal in some states , Some state laws require that the exhaust exits back of the rear axle , Which all side pipes are illegal. Open Headers -Very illegal Also Sound levels
I SAID “ARE YOU SURE YOU WANT TO KEEP IT THAT LOUD?”
Hahaha.
@@Shop209 0:43 it's What?
Just forgot...🥝✔️
11:13
Pretty good, eh, what?
Ishhhhh that is one of the best sounding chevys i heard in a long time 🔥🔥woooo sound awesome to me brutha!👍🏾
Sounds perfect to me mine is open headers and is way louder but once your ears bleed it’s not as loud anymore. Thank you for all the videos the older ones helped a ton and how to find a build sheet glad it was there proved it was a big block ss car. thank you
Might have to put these on mine.
I have those same mufflers. Love them
I have a 74 Nova that I converted the front and rear on and I call it Frankenstein too LOL, I installed electric cutouts on mine though. Its the best of both worlds...Trust me.
I had cut outs for good while, but the motors never lasted very long unfortunately for me. Might've been the brands I bought.
Best solution. Same here, cruise by the cops and smile, cruise by the Mustangs and grin.
I used a set of Hookers Maxflow on my 74 nove 3" and love them
The 3 inch Exhaust is the Best thing You can do for a Big block, I have had a 3 inch on my 67 Chevelle for 20 years and still in new Condition, I have a 468 with 671 Blower, I Ported my 69 corvette Heads 435 hp I open the Exhaust side up a 1/4 inch match Gasket The 3 inch made it all come together, I have wrap around Hooker Headers. 700hp 695 ft pounds but the Exhaust is what made it work Best. KEEP it On Car
I have a set of ten inch rims and tires I put under each tire...gives you about that height and way safer than jack stand.... The way I always worked on my ol Novas... When not around the lift at the shop.
I had that same exhaust system in 2 1/2 on my Nova and it worked very well with the hooker headers. I'm going to be installing Doug's headers and they exit closer to the frame rails and was able to run pretty much straight pipe from the headers to the offset center borlas
I am extremely happy with my long tube headers and 3" Patriot Exhaust H1070 side pipes! Sounds extremely classy yet still rumbly!!
I’ve got some magnaflow straight through mufflers on my 76 Corvette sbc and it sounds great. Not too loud. Aluminum heads and shorty headers. 2.5” exhaust if I remember right.
Music to my ears I love it🤘🏾
Sounds awesome I put 3”
On my 74 ss with super 40s the front is offset in and rear center out with the original style tail pipes that are short and just turn down behind the rear tires where the original hangers are , it sounds amazing my engine is that 355 4 speed stick with 3:08 posi gears 1 7/8 Headers’s cause my first gear in my 4 speed Is that 3:11 first gear trans that’s why I need the 3:08 it’s in
I bought a set of borla straight through offset center. I have not cranked the car yet but I picked them because most people on UA-cam said they were too quiet. They're also really not that expensive compared to their late model specific fit mufflers
3" was a real tricky deal on my 68 4door .. 230 I-6 stock from about parking break wire.. a mere 100 trips to the store and 600 man hours under the car.. but it was worth it.
Lol. I know that feeling
That’s a very wicked sounding lope that that cam has. Enough to scare away a lot of contenders😮. The volume is turned up a little loud but it sure sounds good just like that. 👊😮👍
Yep. Unfortunately I never know how bad the volume will be until after I’m done recording
@@Shop209 yea, I wasn’t real clear about what I was saying. I was trying to say that the tailpipe volume was loud like I like it but you might get a ticket. Love the sound.
I installed a pair of 19.0 inch Dynomax Bullet Resonators 10.0 inches off my big block headers then a pair of Borla XR-1 straight through exhaust mufflers size 3.0 inch x 17.0 inch stopped the mufflers shy of the posi-rear-end, muffler center inline with outer axle weld of the rear end spaced and level, zero drone inside... around 5,000 miles the mufflers should have a deeper growl. Extremely happy, you might try the Borla XS-1 off set... they sound nice on a camaro believe he's in Florida. He's very happy as well.
“If it’s too loud, you’re to … “
Ah, crap! I am getting up there, aren’t I? 😂
It’s not too loud for the first 30 minutes. Lol
Just watched this, super interested to see how it turned out! Did you do a video on that? Thanks!
I’m doing another video on the whole build that will include the exhaust
Looking forward to it, thanks!
I would try going with some Flow Fx, they're a straight through glass pack design but much quieter. love the nova bro!! cheers!!
tail pipes make more of a difference in toning down the exhaust (in cabin) then mufflers do.
try the 3" dynomax ultraflow i have them on my big block Chevelle
That’s the ones I just ordered yesterday to replace these
3 inch is loud. Especially when running straight thru's. I have dual 3 Flowmasters on my FrankenVega, with electric cutouts. So with a flick of a switch, I can go open headers. It took a lot of cutting fitting and welding, but it's well worth it. You can hear the difference at 1:07 into this video. ua-cam.com/video/Tbdxlht-DxI/v-deo.htmlsi=N8UruahKGCYrQegC
That’s a cool ass car. I have some free electric cutouts coming. I may put them on.
@@Shop209 Thanks Much! Do it! You'll love the convenience. I Built mine so it goes straight into the cutouts and branches off to the mufflers, so you get full open headers. I have to check out more of your channel. Keep up the good work.
Sounds great dude 😎🇺🇲
Hush Thrush, Cherry bombs, things never change except the pipe size.
Any way you can do a video on how to center a stubborn Steering wheel? I pulled my wheel off when I got it to find out it's splined so it's not as simple as pulling it off and putting it back on. Nova sounds great even if it's too loud. :)
Since you got onto the topic of exhaust, I'm curious what would be better to lower backpressure? Single *90 out in front of the back tires, or a *45 off the muffler, towards the tire, then another*45 with a pipe coming straight out? Also, may want to look at offset exit mufflers if you are having rear clearance issues. It's been a LONG time since I was part shopping, but I think flowmaster has some.
Loud pipes saves lifes😂
cut up some sidewall off a tire and make hangars with it.. yup straps around pipe like gutter straps or sportbike can strap then a washer and self tapper right into frame whatever, sounds perfect to me . . .
Hey Shop209, I see you have GA plates, I live in Georgia too, I'm in Carrollton GA
I’m a ways from you. Just south of Macon.
@@Shop209 my oldest brother lives in Thomasville, near Tallahassee, me and him saw Dave Mason live on leap day night and went to the famous spook bridge in quitman, close to Valdosta
Cool. I’ve been to that bridge but it’s been forever.
@@Shop209 it's still standing since 1920, it's a good place to go fishing on the withlacoochie river aka old US hwy 84
The dynomax ultraflow are stainless w lifetime warranty. They sound great and will quiet it down. Can you hear me now?
Actually I ordered those yesterday.
@@Shop209those oval dynomax mufflers will quiet it down quite a bit more..that's what I've got on mine (74 nova, 358...465/465 cam..187x heads)( dynomax 3" offset inlet, center outlet) you can flip them either way cuz it's just straight through anyways..and 3 inch exhaust. I've also got an x pipe. Get one and it'll quiet it down even more.
Thrush welded mufflers. Sound pretty good but not crazy expensive. What do you have for a cam? Sounds really good
It sounds great but yeah a little loud.
Magnaflow mufflers might be a good compromise.
Where are your garage doors?
Hey, sorry to be off topic but I need to know about the bumper tucks. Is there a video on it? A muffler shop owner told me I had to give the passenger and fuel tank area (ob) a wide berth. With an exhaust like that, why would you want a radio? Straight thru and not too loud are usually mutually exclusive.
That car sounds good. What size of cam are you running.
It’s a Howard’s cam. 241/247 @ .050
If it's to loud you're to old and I say that was to loud because I am to old.😁 The best thing about electric cars is how they sound, everything else about them sucks but they do sound good.🤔
Ya know, I went from a 2" dual exhaust with Cherry Bombs with rams horn exhaust manifolds to a 2.5" X-pipe system with 1 5/8" headers on my sbc 383 and my car ran the exact QM times before the new system.🤔😯😡 And the Cherry B setup sounded better IMHO.🤨
Both systems sounded similar in the loudness level but the CB had a deeper note. I ordered the new system with turbo style mufflers that aren't annoyingly loud but still sounds like there's something under the hood that has some power when you step on the throttle. It exits out the back and with the windows rolled up, don't hardly notice it cruising in overdrive.😎👍
Nice toys 😊
Good work!
If you have enough room under your car maybe you can run 2 mufflers on each side this just an idea 💡
I might try that if the larger muffler is still too loud. I’m keeping these so I’ll have them.
I think it sounds great if it was out the back ! Why not an out back exit with dumps ? Pre muffler( lol ) So much resonating with underneath exit as far as drivability. And no other vehicle has ever had that same exit as a Nova. All the N.O.V.A.’s as far as I remember. Take care bud
My shock relocation makes the tailpipes pretty hard to install without hitting. I love the way it sounds but it’s just too loud. Gonna go to a different Dyno max muffler.
Sounds bad ass
Sounds good
Love your tire set up. What size are you running?
If I remember correctly, he put 275/60/15 in the back. It might be 50 sidewalls. 15 x8 with if I remember right,5.25 backspacing.
@@justincooper5189awesome! Thanks for the info.
Funny. " THIS MAY BE TO LOUD". 😆😆😆😆
I forgot to tell You Put a Flow master Muffler, Those your using is like not using a Exhaust why use them, You will get a nice rumble with a Muffler
Try some black widow venom mufflers.
Hi John. Question that I'm hoping u know. I have 70 4 door will a 2 Dr windshield trim fit on the 4 door? I need the passenger lower piece. Any info would be appreciated.
No. But I have some 4 door trim. The windshield outer trim?
@@Shop209 yes I just need the passenger side lower piece. How can I get ahold of ya.
The "If it's too loud your too old" thing is non existent after 30, I like loud but you gotta be all to drive it too.
Yeah. Just around town it’d be cool. 4-5 hours at a time is want to get out and walk.
@@Shop209 Right, Where I live in Florida now I do alot of driving up and down U.S. to get to work and to cars and coffee's/cruise-ins/shows so I don't want all that crazy noise.
9:29 They are what?
I don't know what happened but my car started running real bad. Went to change the plugs and gas shot out of 5 of my cylinders. What happened. Thank you
So it happened while driving or was fine when you parked it then cranked it up and wouldn’t run right?
@@Shop209 while I was driving. If I let it set a couple of days it might not run bad but on the other hand it might not make any difference. I change carbs and it still acts like this.
That's illegal in some states ,
Some state laws require that the exhaust exits back of the rear axle ,
Which all side pipes are illegal.
Open Headers -Very illegal
Also Sound levels
Yeah. That’s why I need the dumps to go back to axle tube. Then I’ll be legal. New mufflers are here. Just need to install them and the dumps
What cam is in that thing ?
Rowdy 😎
Rowdy🤓👍
Sounds nasty. Love to hear it.
4:31 Its what?
Borla strsight thru quieter
It just needs a louder radio.
Absolutely
At least you can’t hear the fuel pump1
Lol. It’s noisy when it first primes but you can’t hear it running even with the old quiet exhaust.
👍🏽👍🏽
I run 3 inch on my nova, theres no such thing as too loud,
The solution for long rides is simple… earplugs😂😂
You wouldn't like my exhaust on my square body then lol
I like it. Just don’t want to listen to it for 400 miles. Lol
just courious that is not a 74 the taillights are only 71 and 72
I converted the front and rear to 72.
Ear plugs! lol
No kidding. Freakin LOUD
You wear readers, so of course it's too " Loud", lol
Lol.
Sounds great