The systems that have a panhart bar , do they have any problems when doing a curve with uneven pavement , cause obviously the axle will be moving from side to side as the ride height changes over bumps
+Village Customs want to build a rat rod truck for my shop. but now i'm busy build bike for customer. you guys really inspired even you build a rat rod with inline 4 motor and still cool.
At 3.45 I noticed the Ford in the background. Did you keep the I-beams when you Bagget? And if so do you sell a kit for that also? Hard to tell in the video…
We did a crown vic swap as requested by the customer. I used some of the only bag brackets I could find from airslamit.com. They are for the most part a bolt in bracket.
How much for the front end airbag C-kit you show at the end of this video brother? Do you have a website? Thanks for your time Billy D. (Bear, Delaware)
BIGDADDYFATBOYPUDGE I just use my Facebook page. Village customs nc. My kits go for 1000 to the door. Comes with a video how to install. It's everything you need to install aside the bags. But I sent a link to cheap bags that work well.
I just found your videos today ,yesterday I swapped a dropped axle into a 57 .I been sitting here looking at the stocker thinking I could radius arm it and use it in some kinda build . Then I found your video like some kinda divine hot rod inspiration ! Subscribing this channel is badass !
Bryan Snell yep. You have to run something to hold the side to side. I had a small stupid one laying around that I had on but it has been switched to a nicer longer one since then.
Thanks man, I don't know if you remember but we chatted a little over instagram a few months back about my Willy truck project. I have the Model A beam with the leaf spring that is too wide for it and the shackles are maxed out lol. Getting my parts list together to convert it to bags rather than screwing around trying to either swap the beam or swap the spring. Your setup on the blue truck is helping a lot. Can't wait for you to start uploading your full build videos!
I love the thought of the 0 camber through all the travels. Cornering too.
Thanks for the tips, man! You should make more videos like this. Process build or something like that.
I love that green truck cab
Thank you for sharing. Good stuff man!
Amazing ideas!!!
C1965 M1965 thanks alot :)
Nice setups pal. I love the straight axle one, but I'm a traditionalist.
Do folks have much doing airbag setups like these with fenders still on?
Straights axles under the motor can only go so low... so not really
Can you do something like that to a pickup truck by deleting the leaf springs but keeping the fenders looking like a regular truck
You can.. but the axle will only get so low and then hit the oil pan or frame.
The systems that have a panhart bar , do they have any problems when doing a curve with uneven pavement , cause obviously the axle will be moving from side to side as the ride height changes over bumps
It does, but I'd be surprised even if you were trying to feel it, that you actually would. It's very slight and unnoticable.
I following you on IG. you build a bad ass rat rod. they all owesome
Richard Choppers thanks alot man
+Village Customs want to build a rat rod truck for my shop. but now i'm busy build bike for customer. you guys really inspired even you build a rat rod with inline 4 motor and still cool.
I like your style. 😆 👍 FINS UP 👍
At 3.45 I noticed the Ford in the background. Did you keep the I-beams when you Bagget? And if so do you sell a kit for that also? Hard to tell in the video…
We did a crown vic swap as requested by the customer. I used some of the only bag brackets I could find from airslamit.com. They are for the most part a bolt in bracket.
How much for the front end airbag C-kit you show at the end of this video brother? Do you have a website? Thanks for your time Billy D. (Bear, Delaware)
BIGDADDYFATBOYPUDGE I just use my Facebook page. Village customs nc. My kits go for 1000 to the door. Comes with a video how to install. It's everything you need to install aside the bags. But I sent a link to cheap bags that work well.
That cantilever is that a Chevy truck axle ? Like your style !
Yeah on that one it is. Just an axle I had laying around from a customers car I did a clip on.
I just found your videos today ,yesterday I swapped a dropped axle into a 57 .I been sitting here looking at the stocker thinking I could radius arm it and use it in some kinda build . Then I found your video like some kinda divine hot rod inspiration ! Subscribing this channel is badass !
@@mikesnyder2335 that's awesome man. Glad to have you here :)
Hey Joshua do I see a small panhard bar down there on the passenger side connecting to the torque tube on the blue truck?
Bryan Snell yep. You have to run something to hold the side to side. I had a small stupid one laying around that I had on but it has been switched to a nicer longer one since then.
Thanks man, I don't know if you remember but we chatted a little over instagram a few months back about my Willy truck project. I have the Model A beam with the leaf spring that is too wide for it and the shackles are maxed out lol. Getting my parts list together to convert it to bags rather than screwing around trying to either swap the beam or swap the spring. Your setup on the blue truck is helping a lot. Can't wait for you to start uploading your full build videos!
Let's see something on the dent side f100
What do you charge for the kit
Now days we ship our fronts for 1100 and rears for 700
@@VillageCustoms contact info?
I need info on your kit please.
Did you get Any info? I'd like to buy a kit as well
@@thembrelectric No i haven’t
Nice truck's
Roman Avila thanks alot
One rat rod 1 where’d ya get ur headlights
Two very interested in purchasing a kit from you
?? how much for that kit
I sell fronts 1000 shipped to your door. I sell a full frame kit for 1650 shipped.
Bobber
How low can you go 😅😂😂😂