Scimitar : 3D-printed flying wing

Поділитися
Вставка
  • Опубліковано 30 жов 2024

КОМЕНТАРІ • 84

  • @skydawg98
    @skydawg98 8 місяців тому +7

    I finished printing mine and am installing electronics! Going to fly soon!

    • @yabbiepuncherz5152
      @yabbiepuncherz5152 4 місяці тому +1

      nice, about how much did all the components cost you? I'm contemplating printing out his rifter 3

  • @bizioFPV
    @bizioFPV Рік тому +7

    Looks rad! remarkable landing for a wing with just 1 control surface working!👏

  • @dronepilot260rc
    @dronepilot260rc Рік тому +5

    I always keep about 20 Gemfan flash 6042 in stock. Some of the best props for wings

  • @Матвей-к6ш3р
    @Матвей-к6ш3р 6 місяців тому +1

    Огромный респект мужику за заморочку с проектами и отдельное спасибо за открытые stl файлы с подробным описанием

  • @trumblez
    @trumblez 8 місяців тому +1

    under 50 mah/km is insanely good to me, great job!

  • @dannyhei9077
    @dannyhei9077 10 місяців тому

    this is my first time seeing rc wing fpv flying so smooth like this 👍👍👍

  • @fatihbirkan8527
    @fatihbirkan8527 Рік тому +1

    Another awesome plane from Olivier. Thanks. 👏

  • @salviaaable
    @salviaaable Рік тому +3

    another great plane ! i just have finished printing the sabre 2 hope it will fly well :D this will be my first INAV plane !

  • @RollnHeavyKevy
    @RollnHeavyKevy Рік тому +1

    I'm currently printing the sabre 2. It's an awesome looking plane. I'm planning on mounting the camera on top of the fuselage with a gimble and use a head tracker on my dji air unit.

  • @ApappieK
    @ApappieK Рік тому +6

    Very nice wing design. I like the shape of the wing: larger root chord and smaller wing tips. Less drag at the tips. Clean frontal area and very efficient at high speeds. Hands off in manual mode, INAV 6 is an amazing step forward, I noticed myself! Landing speed was around 50 kmh-ish. Maybe a little CG tuning? How does it fly upside down, close to neutral? And how are stall characteristics? Spiral of death or just nose dropping, backwards V-shaped wings can be tricky? Now I have to choose which plane to print.... 😅 👍 Additionally: prop is rotating in free/clean air = silent = nice for a wing!

  • @jaysonrees738
    @jaysonrees738 Рік тому

    This year, I'm going to try all of your designs! Finally the winter is ending!

  • @jotham123
    @jotham123 Рік тому

    Great idea with the screws! Individual part replacement is important.

  • @francois-alexandrefrancois6334

    wahou !!! merci pour cette vidéo et ce super tuto !! je dois dire que le fpv ne m'a jamais attiré, sauf depuis que je vois tes vidéos !! je me jette sur la grosse vidéo et je vais voir pour commander le matériel fpv !

  • @Aspir3
    @Aspir3 Рік тому

    Already printing it in LW PLA...first part looks gorgious! :D

  • @SerialKoE
    @SerialKoE Рік тому

    Seems to fly great! Merci beaucoup Olivier!

  • @MrFadjule
    @MrFadjule Рік тому

    Your work is fantastic! Your mind is beautiful

  • @marckart66
    @marckart66 9 місяців тому +2

    What size of nozzle did you use to print this? I run with a 0.6mm nozzle always. I find using the PLA-LW i need to have 1 wall, but print it at 0.8mm (which is easy with a 0.6mm nozzle). Using a 0.4 nozzle printing 0.4 wall width, they are just so weak...

    • @Olivier-C
      @Olivier-C  9 місяців тому +1

      Yes Im' using a standard 0.4mm nozzle, makes the walls thin and weak for sure, but that's the only way to have something light enough. Unless using a bigger nozzle and a light plastic like PLA-LW

  • @locarshobbies
    @locarshobbies Рік тому +1

    Amazing model! super modular, the way models should be designed! so good! the only reason i am reprinting is because i forgot i was inverted and pulled on the wrong way hahah :D

    • @Olivier-C
      @Olivier-C  Рік тому

      Did you manage to break all the parts ?! O.o

  • @yakymua
    @yakymua Рік тому

    Beautiful. Magnifique!

  • @hagenissen666
    @hagenissen666 6 місяців тому

    Minmatar! Your line of planes are named after Minmatar ships from EVE. I really want to have a Sabre!

  • @n1vca
    @n1vca Рік тому +3

    Wow, relatively silent, very fast and efficient 👍Great design! What is the stall speed?

  • @apexkong6331
    @apexkong6331 Рік тому

    @Olivier FPV pouvez-vous donner un lien vers la tringlerie de servo que vous avez utilisée?

  • @henrirotthier5710
    @henrirotthier5710 Рік тому

    Excellent. Et qu'est-ce qu'il va vite 😮

  • @apexkong6331
    @apexkong6331 Рік тому

    @Olivier FPV can you give a link to the servo linkage you used?

  • @dronepilot260rc
    @dronepilot260rc Рік тому

    Wow I need to get my printer up and running again 🎉

  • @ericevans6080
    @ericevans6080 10 місяців тому +1

    Is the data in the video part of the goggle view? The altitude, speed etc. and the GPS track view or is that post processing in the stored video only?

    • @Olivier-C
      @Olivier-C  9 місяців тому +1

      I have some OSD that shows me about the same informations in the goggles, but what see in the video is post-processed, overlayed using a software called Dashware, it uses the blackbox and telemetry files to add the values over the HD footage.

  • @ArmageddonYT
    @ArmageddonYT Рік тому

    Ça donnerait envie cette petite aile.. si c'était pas si lent en impression 3d 🙂 ni si fragile.. je manque encore un peu d'expérience 😊

  • @guoleli7627
    @guoleli7627 Рік тому

    飞机设计的很漂亮,UI设计也是非常的简洁美观,请问UI是什么品牌的设计?❤

  • @MONSTERPC-el9hh
    @MONSTERPC-el9hh Місяць тому

    hi olivier , ım currently building the model airplane called scimitar ,but I noticed that the fusulage 3 and 4 files are different from those in the video.Have the files been updated , and if so, where can ı find them?

    • @Olivier-C
      @Olivier-C  Місяць тому

      Everything is there on the first page : www.rcgroups.com/forums/showthread.php?4223695-Rifter-Sabre-Scimitar-mini-sized-FPV-cruisersIF it's not too late, print the Scimitar v2 !

  • @СергейТимченко-х9р

    Спасибо, очень КРУТО, Вы просто молодец👏

  • @Notarocketscientist
    @Notarocketscientist 4 місяці тому

    Hi, I have a question, my friend, he is the beginner, and he wants to start with building your airplane, and than fly it as his first aircraft. Would you recommend doing that, or disapprove? Because I think that. he should choose different aircraft for starting. What do you think about it?

    • @Olivier-C
      @Olivier-C  4 місяці тому

      hi, if he never pilot a fixed wing, I don't think that's best to start with a 3D printed plane, these are more fragile than foam planes. Instead I would recommend a twin tractor like the AtomRC Penguin, it's an excellent plane for beginners, and then once he's trained enough, he can print a Scimitar ! :)

  • @Fabwize
    @Fabwize Рік тому

    jolie, bien joué

  • @toyzndahood
    @toyzndahood Рік тому

    Magnifique!!

  • @benboul8597
    @benboul8597 Рік тому +1

    Cool les vidéos 👏Qu'est-ce tu appelles mode manuel ? Et tu conseils quoi comme avion pour avoir quelque chose de précis ? Notamment pour faire de la cinematic en vidéo type ?

    • @Olivier-C
      @Olivier-C  Рік тому +1

      le mode manuel c'est sans la stabilisation active du controleur de vol. Control direct des gouvernes. C'est quoi exactement que tu entend par cinematic ?

    • @benboul8597
      @benboul8597 Рік тому

      @@Olivier-C ok merci pour les infos 👌La cinematic c'est le fait de faire des plans aérien très smooth et "cinématographiques". On voit souvent ça en drone fpv ou les mecs font des supers belles vidéos en razmotte ou en faisant des gros dive le long du falaise ou d'un immenble.
      Autre chose sur le mode automatique,jai des vieux esc d'avion qui traînent dans mes placards. Ils ont au minimum 10 ans. J'imagine qui ne prennent pas en charge l'autonomie ? C'est une techno assez récente, non ?

    • @Olivier-C
      @Olivier-C  Рік тому

      @@benboul8597 les vieux ESC ca marche toujours, les protocoles PWM sont toujours supportés !

    • @benboul8597
      @benboul8597 Рік тому

      @@Olivier-C mais je n'aurai pas de fonction de stabilisation auto, si ?

    • @Olivier-C
      @Olivier-C  Рік тому +1

      @@benboul8597 Pour la stabilisation il faut un controlleur de vol, en F405 ou F7**, avec dessus en soft soit INAV soit ardupilot

  • @killianavellaneda8116
    @killianavellaneda8116 2 місяці тому

    franchement bravo ca vol super bien , niveau imprimante , faut un pateau de combien pour que tout passe ? cest du pla ou abs etc?

    • @Olivier-C
      @Olivier-C  2 місяці тому

      en PLA+ et PLA-LW, de mémoire il faut un plateau de 220x220x220 mini, me souviens plus à 1cm près

    • @killianavellaneda8116
      @killianavellaneda8116 2 місяці тому

      Merci j'ai une flsun sr mais les plateau rond ça fait perdre de la place a mort

  • @KudikaKudesnik
    @KudikaKudesnik Рік тому

    Very nice model. Fast and beautiful. how big a battery can you put on it?

  • @danthenauticalman1
    @danthenauticalman1 Рік тому

    Nice. I have printed all but fuselage 1. Do you have the fuselage 1 file with the cam cutout? The one in parts folder is solid.

    • @Olivier-C
      @Olivier-C  Рік тому

      In the folder /extras there's the SCM nose and the adapters !

  • @m0rgul
    @m0rgul Рік тому +1

    Hello Oliver. Thanks for the model! Can you help me to find the correct CG.

    • @Olivier-C
      @Olivier-C  Рік тому +4

      Hi! Theres 2 small triangles on the sides on the part fuselage 2

    • @m0rgul
      @m0rgul Рік тому +1

      ​@@Olivier-C thanks lot

  • @kurkurstuff2522
    @kurkurstuff2522 Рік тому +1

    how heavy is it just the 3d printed parts alone?

    • @Olivier-C
      @Olivier-C  Рік тому

      About 370 grams, there's all specs here : www.rcgroups.com/forums/showthread.php?4223695-Rifter-Sabre-Scimitar-mini-sized-FPV-cruisers

    • @kurkurstuff2522
      @kurkurstuff2522 Рік тому

      @@Olivier-C dang I'm about to print a 800g-1kg plane. and it still looks small. I'm thinking of scaling it 200%. could you recommend a motor specs for 1kg plane and 2kg plane respectively?

  • @terracoon9882
    @terracoon9882 Рік тому

    looks very good! i want to print it, what screw sizes do I need?

  • @neilrothwell5561
    @neilrothwell5561 Рік тому

    Olivier what temperature are you using for the LW-PLA and is it using the profiles you published?Any changes to flow etc?

    • @Olivier-C
      @Olivier-C  Рік тому

      I added my setting for PLA-LW in this post : www.rcgroups.com/forums/showpost.php?p=49958197&postcount=5

    • @neilrothwell5561
      @neilrothwell5561 Рік тому

      @@Olivier-C Olivier, many thanks I missed that!

    • @neilrothwell5561
      @neilrothwell5561 Рік тому

      I have a Creality Ender 3 Neo V2 and it printed the wing very nicely, I had to change the flow to 60% for the whole wing as otherwise there wasn't good adhesion. Nice and strong with the infill.

  • @servetgenc6617
    @servetgenc6617 Рік тому

    I'm downloading the Rifter model design, but it doesn't open. Do I need to install a program?

    • @literally_not_kevin
      @literally_not_kevin 5 місяців тому

      The .3mf files need to be opened with a slicer program of your choice. The CAD files are all Fusion360 if I remember correctly.

  • @ayoaina_fpv
    @ayoaina_fpv Рік тому

    Great stuff! Well balanced! Lightweight PLA? And was that a real bumblebee? Lol

  • @DG10-youtube-channel
    @DG10-youtube-channel Рік тому

    Awesome!

  • @kibbycabbit
    @kibbycabbit 8 місяців тому

    Wow, what's your launch throttle and idle throttle set at?

    • @Olivier-C
      @Olivier-C  8 місяців тому +2

      Im not using INAV auto-launch if that's what you're asking, I'm throwing in angle mode, with about 70-80% throttle maybe

  • @raymondvanbeek9741
    @raymondvanbeek9741 Рік тому +1

    Hey what a nice plane. I have print it. Can you make a video how you find the cg point on the wing?

    • @Olivier-C
      @Olivier-C  Рік тому +2

      Theres 2 triangles printed on the side of the fuselage

  • @SonAndDadFPV
    @SonAndDadFPV Рік тому

    looking good, no problem with the black LW PLA in the sun? (sagging?)

    • @Olivier-C
      @Olivier-C  Рік тому +1

      no PLA-LW on this prototype, it's all PLA+ !

  • @catfish828
    @catfish828 Рік тому

    Fantastic

  • @anlpereira
    @anlpereira 6 місяців тому

    What board is used to get telemetry data? Thanks

    • @Olivier-C
      @Olivier-C  6 місяців тому

      The log file is made by INAV, recorded on the SD card, on this plane the flight controller is a classic F405 . I have a video to explain how it's overlayed, will release soon

  • @Rick-ox5yh
    @Rick-ox5yh 10 місяців тому

    I printed one,but where's the CG mark?

    • @Olivier-C
      @Olivier-C  10 місяців тому

      under the wings there's 2 little triangles, on the fuselage sides

  • @flyingcatto404
    @flyingcatto404 Рік тому

    can it printed using vase/spiral mode?

  • @jacobdavidcunningham1440
    @jacobdavidcunningham1440 Рік тому +1

    7:26 the up deflection seems high

  • @pawemarszaek3007
    @pawemarszaek3007 Рік тому

    Flight controller i allways i need ?

  • @patricehonvault2612
    @patricehonvault2612 Рік тому

    Et la vérification pré-vol ! J'entends encore mon instructeur 😅

  • @EnglishTurbines
    @EnglishTurbines Рік тому

    Plenty of wing sweep, very good...A common design flaw from China....🤔😳😳🇬🇧

  • @SonAndDadFPV
    @SonAndDadFPV Рік тому

    lol, you flew wing with only one servo....