I know a few people that have built these, and I'm collecting the parts to do so myself. Normal compressors are WAY too loud. These scroll compressors from HVAC or Fridges are super quiet! Very nice build using a fire extinguisher tank. Using a drilled out bolt for the air fitting is clever. Nice Work!
That is a really nice job, over here in the UK, our CO2 fire extinguishers usually have an aluminium body, yours will be stronger. Thank you for posting.
You're lucky to have that welder at hand because not many of us have one just laying around at our disposal to spot weld parts together. I bet you did good in Shop class. ;o)
Hi, I’ve made 15 so-to-speak quiet air compressors for family and friends from different-brand-name air tanks and using previously working dehumidifier (or window AC) refrigeration compressors and all worked fine. I’ve recently come across a problem I can’t seem to resolve. NOW: Like in the past, I’m using a 6 gal air compressor tank, window AC refrigeration compressor, new 4-way pressure switch with unloader valve, and new tank check valve which holds pressure fine….. PROBLEM: after filling the tank and the unit shuts down…a small amount of OIL VAPOR (smoke) comes out of the unloader valve…..just for a minute or less. Then it stops smoking. So I tried using 3 different refrigeration compressors (from a dehumidifier, etc.) and still same problem. (I did this in case the first refrig compressor had a bad internal seal….can’t believe ALL THREE had bad seals, so maybe (??) the problem lies elsewhere…. To further CONFUSE this issue, I disconnected the refrig compressor from the check valve and simply ran the refrig compressor for a long time, then shut it down and NO VAPOR………wow, I’m really stumped! This is “nothing different” than what I’ve done in the past 15 builds yet….SOMETHING MUST BE DIFFERENT…to cause this oil vapor. Any suggestions as to WHY this might be happening would be really be appreciated.
The compressor has a relay unit equiped with over load protector, is missing.That four rubber bushings can have been used. It will reduce vibration and noice
Pour des raisons de sécurité de l'utilisateur de ce compresseur ainsi que toutes personnes approximatives du lieu, il est impérativement exigé d'installer une soupape de sécurité réglée à une pression légèrement supérieur à la pression de service (sortie compresseur). Autrement, et en cas de disfonctionnement du pressostat, le compresseur continuera à comprimer jusqu'à explosion de l'ensemble. C'est comme une bombe !
Using fridge or aircon compressor is good due to its quiet operation, but it will not last. The check valve flappers will corrode and it will lost compression sooner maybe for 3 to 6 months
هذا ما ننتظره من الغرب بشغف ليكونوا مصدر الهام للشباب حول العالم ولا يكونوا دعاه للمجون والاباحية This is what we eagerly await from the West to be a source of inspiration for young people around the world And do not be advocates of indecency and pornography
No pones fuga de aire, al quitar las protecciones (como el termoprotector) que trae el motor, ya le quitas utilidades al motor. No está mal el tutorial, pero puede mejorarse.
that's a great idea. what i would do differently, i would not weld the front screw of the fire extinguisher (where the fire extinguisher would be filled up) and would use it to drain water....Please don't spray compressed air on your skin that's bad, you can google effects of it.
This is fake... first there is no PTC Relay, that compressor wouldn't start Second, he spent alot of air during the video, and in the end of the video ,you can see the pressure gage didn't move an inch... That reservoir is pretty small, so the pressure would drop quite a lot. He has the hose connected to another external compressor, as you can guess it by how much he cropped the video afterwards This guy's videos are all fake, he just makes a very good job of keeping it looking kinda real, so he can fool most of the normal people.
Nice work! However, I'd recommend anyone (UA-cam DIYers out there} trying this on their own to do a hydrostatic test on the tank before putting under load. Failed tank can mean a massive hole in a wall, or worse, death. Be safe!
Yeah welding on the tank like that probably compromised the tank. It hopefully fails at the welds on the bolt if anything instead of the tank exploding. Assuming it just blows the bolt and power switch pressure regulator thing off. That could be dangerous to tho and those where all cold spot welds to so they definitely aren't very strong weld. The material building up on top like that means no penetration still made the tank hot tho.
Inside a unit in service is different than here refrigerant has oil in it from factory witch constantly lubricates moving parts in this fashion it will no longer have constant oil supply so in turn probably won't be reliable
@marthale7 actually, the freon that this pump sends through the refrigerator coils is also the lubrication for the pump motor parts. That's why you don't see more videos of people using these for compressors. It's not a new idea.............
I really enjoyed your video ….. great craftsmanship 🙏 are you in South east Asia ? … I love it when you just see the dogs legs ….haha … excellent 👌, just subscribed
This is fake as shit lol... first no PTC Relay, second, he spent alot of air during the video, and in the end you can see the pressure gage didn't move an inch... That reservoir is pretty small, and the pressure would drop like crazy. He has the hose connected to another external compressor, you can guess it by how much he cropped the video afterwards
Hi, I would like to build this but I am a little confused, How do you stop oil from the compressor to go to the air tank, I mean the compressor is full of oil so how do I stop that oil from getting into the air tank ? or is there no oil coming out from the outlet line ? Thank you
Spanish Letter. El sonido de ese motor compresor no es. 2 fallos observados. 1 fallo fail la manguera transparente debería ser manguera para alta presión en lugar de esa transparente. 2 fail. Ponerle sus partes eléctricas como el relay y el termico ' ese compresor porque así esos cable soldados así no prende porque debe iniciar la bobina de arranque del compresor ' yo trabajo en refrigeracion. De resto yo le admiro su labor esta muy lindo el diseño y las iniciativas para las personas.
Need to use Teflon tape on the pressure joints. Need a condensation drain. No ground on the wiring = getting a nasty shock! I doubt this will have much use and or last long.
It is not practical because ref compressors are high pressure but low volume flow. It will take very long time to fill flat tire at vulcanizing shop while you need a fast work there.
No nylon thread tape on anything, so it probably leaks air. 1/4 tubing is crap, so it probably doesn't have very much psi. And worst of all, the electrical is not enclosed, so be prepared for a nice electrocution if it gets wet.
nem pois bucha pra travar o motor e não vibrar, e nem deixou mostrar o motor ligando automático ao cair a pressão no extintor. mas de tudo mais 👍👍👍 isso me inspira!!!
Hola el pico que mostras en el minuto 4:57 es de hierro o bronce?. Disculpa mi ignorancia a duda es cuando lo soldas con la MIG, si fuese bronce también se puede soldar con MIG?. Gracias
Compressor ke suction me silica jel filter ka use karo. Moiture enter hone se compressor ke valve damege ho jayega piston jam ho jayega. Ye compressor air pump ke liye hai.
Схема рабочая, не спорю. Но какой объём данного ресивера? Литров 5-7? И давление 3,5 кг , А в конце столько баловался, а стрелка манометра даже не шелохнулась, опять на мелочах обман
No Teflon tape...no intake air filter... Using bolt for pipe fitting...no handle for pulling...these compressors are so slow, not designed to be air compressors. Also pressurized air is dangerous blowing it on body parts...can cause air bubbles in blood stream.
I don't know if somebody commented it yet, but you SHOULD NOT weld zinc plated parts, it produces carcinogenic fumes which you must avoid breathing!!! Try to remove the zinc coating with mechanical means.
*I turn Fridge Compressor into a 12v Air Compressor* ua-cam.com/video/LYjIXZz1PNc/v-deo.htmlsi=gger-hLIksjnVVZs
Try using a little teflon on the pressurized threads. And someone else pointed out that you may need condensation drain at bottom. I agree 👍
I know a few people that have built these, and I'm collecting the parts to do so myself. Normal compressors are WAY too loud. These scroll compressors from HVAC or Fridges are super quiet! Very nice build using a fire extinguisher tank. Using a drilled out bolt for the air fitting is clever. Nice Work!
Thank you for good comment. If this video is useful for you, please share it's
Sir..this air compressor helps for cement plastering for walls are not...pls tell me sir
This is not a scrollcompressor.
It is a piston compressor.
jest.iedno.ale.sprezarka.gzeiesie.wsrodku.silnik.faiczysie.zczasem.zlom
This is a piston compressor not a scroll
... well done, congrats. How do you keep the compressor with oil?
That is a really nice job, over here in the UK, our CO2 fire extinguishers usually have an aluminium body, yours will be stronger. Thank you for posting.
yes. I'm in Vietnam, our fire extinguisher is made of iron
Yes and your money is made from paper haha get with the times
Love from Australia
You're lucky to have that welder at hand because not many of us have one just laying around at our disposal to spot weld parts together. I bet you did good in Shop class. ;o)
JB WELD steel epoxy apply and wait 2 days and itll hole better then these cold welds
Actually looks like he's not the best welder
Compressor needs a drain out valve at the bottom of the tank.👍
and put the valve bypass, it will protect leadvalve of compressor loss
JD w. Can you explain a bit more?
How long does the compressed air last in this tank, if it is stirred continuously?
Thanks in a million. Great content. Awesome imagination. Grade: A++💥
That’s super awesome 👏
Thank you
Muy bien por usted Profe .Muchas Gracias.
Great use of you skills!!
Los motores de refrigerador necesitan el automático de arranque sino no funciona ! Por que se lo sacó ? Como hace para que arranque ?
Hi,
I’ve made 15 so-to-speak quiet air compressors for family and friends from different-brand-name air tanks and using previously working dehumidifier (or window AC) refrigeration compressors and all worked fine. I’ve recently come across a problem I can’t seem to resolve.
NOW: Like in the past, I’m using a 6 gal air compressor tank, window AC refrigeration compressor, new 4-way pressure switch with unloader valve, and new tank check valve which holds pressure fine…..
PROBLEM: after filling the tank and the unit shuts down…a small amount of OIL VAPOR (smoke) comes out of the unloader valve…..just for a minute or less. Then it stops smoking.
So I tried using 3 different refrigeration compressors (from a dehumidifier, etc.) and still same problem. (I did this in case the first refrig compressor had a bad internal seal….can’t believe ALL THREE had bad seals, so maybe (??) the problem lies elsewhere….
To further CONFUSE this issue, I disconnected the refrig compressor from the check valve and simply ran the refrig compressor for a long time, then shut it down and NO VAPOR………wow, I’m really stumped!
This is “nothing different” than what I’ve done in the past 15 builds yet….SOMETHING MUST BE DIFFERENT…to cause this oil vapor.
Any suggestions as to WHY this might be happening would be really be appreciated.
The compressor has a relay unit equiped with over load protector, is missing.That four rubber bushings can have been used. It will reduce vibration and noice
Muito bom, vc ganhou mais um escrito
How compressor work with two wires? No starting circuit
It's a puny ONE horsepower fridge motor, unlike the "ADVERTISED 10 horsepower" so wouldn't need a lot.
it can run if you know the wiring
Good idea no one has ever done it thank you very much
Pour des raisons de sécurité de l'utilisateur de ce compresseur ainsi que toutes personnes approximatives du lieu, il est impérativement exigé d'installer une soupape de sécurité réglée à une pression légèrement supérieur à la pression de service (sortie compresseur).
Autrement, et en cas de disfonctionnement du pressostat, le compresseur continuera à comprimer jusqu'à explosion de l'ensemble. C'est comme une bombe !
Nice project! The compressed air doesn't smell freon? I use the compressor without a tank and the compressed air smell really bad
Using fridge or aircon compressor is good due to its quiet operation, but it will not last. The check valve flappers will corrode and it will lost compression sooner maybe for 3 to 6 months
هذا ما ننتظره من الغرب بشغف ليكونوا مصدر الهام للشباب حول العالم
ولا يكونوا دعاه للمجون والاباحية
This is what we eagerly await from the West to be a source of inspiration for young people around the world
And do not be advocates of indecency and pornography
what's the maximum psi for that tank? thank you and awesome project.
20 bar
@@walterwhite7279 on what period of time this fiew litre reservoir is exceedin the goal pressure of twenty bar?
Cara faltou o dreno para água acumulada.
Fora que o óleo do compressor vai todo embora.
На выходе компрессора обязательно должен быть масляный фильтр, иначе заклинит.
No pones fuga de aire, al quitar las protecciones (como el termoprotector) que trae el motor, ya le quitas utilidades al motor. No está mal el tutorial, pero puede mejorarse.
that's a great idea. what i would do differently, i would not weld the front screw of the fire extinguisher (where the fire extinguisher would be filled up) and would use it to drain water....Please don't spray compressed air on your skin that's bad, you can google effects of it.
O
l00
O
l00
Ll
This is fake... first there is no PTC Relay, that compressor wouldn't start
Second, he spent alot of air during the video, and in the end of the video ,you can see the pressure gage didn't move an inch... That reservoir is pretty small, so the pressure would drop quite a lot.
He has the hose connected to another external compressor, as you can guess it by how much he cropped the video afterwards
This guy's videos are all fake, he just makes a very good job of keeping it looking kinda real, so he can fool most of the normal people.
how many bars maximum?
How long until full
Hello, what a good video I would like to know what the materials are, thank you, greetings from Chile
Thanks in a million. Great content. Awesome imagination.
Nice work! However, I'd recommend anyone (UA-cam DIYers out there} trying this on their own to do a hydrostatic test on the tank before putting under load. Failed tank can mean a massive hole in a wall, or worse, death. Be safe!
Zé do contra.
Yeah welding on the tank like that probably compromised the tank. It hopefully fails at the welds on the bolt if anything instead of the tank exploding. Assuming it just blows the bolt and power switch pressure regulator thing off. That could be dangerous to tho and those where all cold spot welds to so they definitely aren't very strong weld. The material building up on top like that means no penetration still made the tank hot tho.
It’s 40 psi. Big deal.
is nice DIY project. but im quite interesting is where you get ur soldering iron.
Great job ☝️👍
Thanks you brother infomation tutorial the best 👍👍
Congrats you did it, Great
Can you provide a Link for that Pressure Switch/relay ??
Hello is an interesting project. I have one question, if the piston is not lubricated and works only on air, will it be exploited? Will it be durable?
Inside a unit in service is different than here refrigerant has oil in it from factory witch constantly lubricates moving parts in this fashion it will no longer have constant oil supply so in turn probably won't be reliable
@marthale7 actually, the freon that this pump sends through the refrigerator coils is also the lubrication for the pump motor parts. That's why you don't see more videos of people using these for compressors. It's not a new idea.............
How do you start the fridge compressor without connection the start coil?
Hey bro! What type of welding machine you are using?
I really enjoyed your video ….. great craftsmanship 🙏 are you in South east Asia ? … I love it when you just see the dogs legs ….haha … excellent 👌, just subscribed
Only the return valve was missing so as not to damage the compressor valves
Bro compressor relay also missing
Ficou bom...mais faltou alguns kit de segurança....como válvula de proteção, dreno de ar e uma válvula pra não retornar ar pro motor
Without ptc relay? How to work?
This is fake as shit lol... first no PTC Relay, second, he spent alot of air during the video, and in the end you can see the pressure gage didn't move an inch... That reservoir is pretty small, and the pressure would drop like crazy.
He has the hose connected to another external compressor, you can guess it by how much he cropped the video afterwards
Perfect and excellent work 👏 👌 👍
Hi, I would like to build this but I am a little confused, How do you stop oil from the compressor to go to the air tank, I mean the compressor is full of oil so how do I stop that oil from getting into the air tank ? or is there no oil coming out from the outlet line ? Thank you
Buen trabajo pero tendrías que ponerle un pulgador para la condensación del agua, por lo demás todo bien me gusta mucho
Ese motor de nevera tarda 45 minuto en yen at el tanque
Производительность этого компрессора ну просто зашкаливает
О, да! Чтобы дуть через трубочку - самое то!!
Spanish Letter. El sonido de ese motor compresor no es. 2 fallos observados. 1 fallo fail la manguera transparente debería ser manguera para alta presión en lugar de esa transparente. 2 fail. Ponerle sus partes eléctricas como el relay y el termico ' ese compresor porque así esos cable soldados así no prende porque debe iniciar la bobina de arranque del compresor ' yo trabajo en refrigeracion.
De resto yo le admiro su labor esta muy lindo el diseño y las iniciativas para las personas.
Segun se pone guantes para soldar y esta en sandalias
No pos que cayó a detener ya en los pies ( pero esta chido su compresor )
Maravilha parabéns amigo gostei muito
몇마력 정도의 압력이 생기나요??
Só faltou um puxador pra conduzir o compressor. Muito bom parabéns
Viu se ele colocou válvula de segurança?
Saludos y felicitaciones, yo por medio del tu yo, construí uno igual, pero fuimos a pintar un techo y la presión dura poco, que puede pasar?
Very good service 👌👍
👍 Only missing things are drain valve & safety valve.
Need to use Teflon tape on the pressure joints. Need a condensation drain. No ground on the wiring = getting a nasty shock! I doubt this will have much use and or last long.
أحسنت على هذه الفكره الرائعة وعلى هدا التوضح
Z tym agregatem z lodówki to się napełnia lata świetlne
witch welding system you using ?
Could this handle an impact wrench for example?
Espectacular..
Muy creativo...saludo desde paraguay !!
Sorry King. That compressor is refrigerant cooled. No refrigerant, no cool. Will overheat quickly.
For spray no problem..i know that.How about to loose nuts,especially for automotive works?
is this compressor is suitable for spraying paint
boss pa send naman sa wiring from compressor to pressure switch at sa outlet...thank you
It is not practical because ref compressors are high pressure but low volume flow. It will take very long time to fill flat tire at vulcanizing shop while you need a fast work there.
No nylon thread tape on anything, so it probably leaks air. 1/4 tubing is crap, so it probably doesn't have very much psi. And worst of all, the electrical is not enclosed, so be prepared for a nice electrocution if it gets wet.
Why the pressure gauge needle never shows a drop in pressure when your blowing air on your leg,arm and hand ?
Bro you are not give supply compressor starting point and nothing give tourk so why your compressor start😮
Please go back to school and learn how to spell. No one can understand you
will the motor work without relay or overload protection?
What kind of welding device do you use in welding?
Thank you
Where do you buy the parts?
nem pois bucha pra travar o motor e não vibrar, e nem deixou mostrar o motor ligando automático ao cair a pressão no extintor. mas de tudo mais 👍👍👍 isso me inspira!!!
Hi
Can we use as a painting compressor?
I suppose so...I'm building one for myself.
o melhor vídeo que assistir, o cara não falou nada mais eu entendi perfeitamente
the oil of the compressor is mixing with air coming out.
this is an amazing stuff to use at home!
Well done superb.
Hola el pico que mostras en el minuto 4:57 es de hierro o bronce?. Disculpa mi ignorancia a duda es cuando lo soldas con la MIG, si fuese bronce también se puede soldar con MIG?. Gracias
Vc Vende Também Amigo
para hacer la prueba tenia que estar enchufado n ?
Nice build, but one way valve is a must to put on the intake side. or is it just me. nevermind. great job. :)
and put the wires into a box, prevent touching. :D
Will it work for sprey painting work?
Hello
Have a good idiya.
Hello brother,
1)this compresser how much HP?
2)this compresser is automatically cut off and on?
vous avez fait un travail formidable mais vous avez oublié d'installer le filtre a air
Compressor ke suction me silica jel filter ka use karo. Moiture enter hone se compressor ke valve damege ho jayega piston jam ho jayega. Ye compressor air pump ke liye hai.
Is it a tank extintor?
Схема рабочая, не спорю. Но какой объём данного ресивера? Литров 5-7? И давление 3,5 кг , А в конце столько баловался, а стрелка манометра даже не шелохнулась, опять на мелочах обман
I tried to put 220V on the motor but it doesn't start. What do I need to do to start the engine?
Nice job
Shouldn't there be a one way valve?
Mine can't start again when pressure goes down after filling it
No Teflon tape...no intake air filter... Using bolt for pipe fitting...no handle for pulling...these compressors are so slow, not designed to be air compressors. Also pressurized air is dangerous blowing it on body parts...can cause air bubbles in blood stream.
يجب ان يكون في الهواء الداخل صباب هواء عدم رجوع لكي لا يصبح علا الضاغط ضغط كبير وشكرا
this is what we called innovations
Kaunsa welding machine use karte bhai
I don't know if somebody commented it yet, but you SHOULD NOT weld zinc plated parts, it produces carcinogenic fumes which you must avoid breathing!!! Try to remove the zinc coating with mechanical means.
Buenas... Le faltó mostrar cómo conectar el compresor, porque con fase y neutro solamente, ese compresor no parte, debe agregar algo más, saludos
Can I use this project for spray painting.please reply asap.
Muito Bom!!!!! Brazil.
Can we use in air die grinder..???