Dear your videos r very helpful specially for the beginners. Great I am using pix hawk 2.4.8 in my quad copter and while reinstalling firmware after flushing the old firmware, I’m stuck up at Reading Hex. And connection error is shown afterwards. I am selecting Ac3.6.7AP3.9.7 as firmware to install kindly help. Thnx
accel calebreation. .. successful. .. Showing. .. But the 3d monitor direction different !! While I rotate left shoing right rotating. What can I do sir please tell... I not found any solution
hey man i hope you see this, so i shorted the two pins using solder, and also the mission planner is identifying that my board is moving this includes the compass yet the calibration does not work i checked and my the compass on the mission planner is right in which direction my board is pointing yet the mission planner doesnt seem to work please help
@@techathome yep that's an option but I got where problem was, Mine usb cable was broken near the micro usb adapter so from the exposed wire electromagnetic interference was distributing the compass of the controller! I changed the USB cable, then everything was working properly!
There are lot of fake boards available in the market, I think in your APM there is no compass. You can connect external compass that comes with GPS module Refer this: ua-cam.com/video/jHaYAA_Km7Y/v-deo.html
It has worked for me, thanks lot . I supposed to through the flight controller but after watching your video- I tried and its working .
Good information 🙏
Very useful video
Thank uh so much ,it's very helpful to me❤️🙂,please do more videos
Welcome
Thank you
Thank so much
Welcome
Hi thanks it solved, showed dots but itis not collecting samples on rotating it only shows dots n few samples 3 or 6 any idea how to solve it
Sir pls help in my apm dots are collecting but while doing calibration it suddenly stucks.
Thanks bro
welcome
hello my drone unbalanced to down side while takeoff , what to do ? ,please help.
Muchas gracias, justo eso me estaba pasando.
Welcome
@@techathome pero ahora aparecen los puntos blancos y no giran los rayos que los atrapan.
Muchas gracias
@@hzanfra hola lograste solucionar? a mi hasta ahora no me aparecen los puntos blancos, me ayudas por favor soy nuevvo en esto
@@pablosandrobutrongaray806 cambie la APM
can I use this fot cube black?
Dear your videos r very helpful specially for the beginners. Great
I am using pix hawk 2.4.8 in my quad copter and while reinstalling firmware after flushing the old firmware, I’m stuck up at Reading Hex. And connection error is shown afterwards. I am selecting Ac3.6.7AP3.9.7 as firmware to install kindly help. Thnx
Click on install firmware legacy and try
What about on pixhawk board
Bhai g ya b Kar liya but problem is not end compas is not connected
accel calebreation. .. successful. ..
Showing. ..
But the 3d monitor direction different !!
While I rotate left shoing right rotating.
What can I do sir please tell...
I not found any solution
Have you placed the flight controller Arrow mark towards front direction?
if that happens to pixhawk what is the solution
hey man i hope you see this, so i shorted the two pins using solder, and also the mission planner is identifying that my board is moving this includes the compass yet the calibration does not work i checked and my the compass on the mission planner is right in which direction my board is pointing yet the mission planner doesnt seem to work please help
Thanks the dots r appearing but the red dot is not moving all the way around, it's just moves in 1st or 2nd quadrant. Any solution for that?
Then I think you have to use the external Compass of GPS module
@@techathome yep that's an option but I got where problem was,
Mine usb cable was broken near the micro usb adapter so from the exposed wire electromagnetic interference was distributing the compass of the controller!
I changed the USB cable, then everything was working properly!
Ok, then fine
Bro i'm using mission planner android software,while doing live compass calibration the app get stuck and doesn't respond
I have not tried Android version bro, it's better if you try with Windows computer
@@techathome bro is it necessary to do compass calibration. My drone is armed and flying well
it does not work ,can you help me please.i am making drone from last 3years and it still working
You have to use external compass that comes along with GPS module
In pixhawk ,kaha pe sort karna parega
Sorry, pixhawk i have not used
Hai, can you say how to fix bad gyro health?
Try to reinstall firmware and calibrate once again
Are you getting point for compass??
Do i have to remove jumper if I am using gps
No
In my apm 2.8,there is mo red light blinking why
Change the USB cable and check
Apm mein compass caliberation ho hi nahin Raha dant dikh hi nahin Raha
Where to get the jumper im facing the same problem now pls help
You can connect normal jumper wire which is used in Arduino projects
Bro i short that 2 point but also i can't see that dot dot points... what can i do now ?
It means your board is not having onboard compass
U have to use external
@@techathome but apm 2.8 have internal compass
Not all, there are lot of fake boards available
Bro.. i add a external gps but then also i doesn't see any point when i do the compass calibration
I think you have to check mark on, Use external compass option
even trying this method not working for me plz help me bro
You need to go with external compass that comes with GPS module.
I am face same problem and i follow your video but problem not solve.. please lelp
I am not exactly sure, if possible replace tha Apm board and check once
even after doing this it's not working. what should i do
May be your board not having built-in Compass,
You can try with external Compass of GPS module
@@techathome but how APM doesn't have internal compass.
I have heard, not exactly sure
There are lot of clone boards.
Try to change the cable, if you can and check once.
Bro can we remove the jumpers after calibration?
No
Keep it connected
my bord saying "compass error :99"
please say???
Connect external Compass that comes with GPS module and try once
@@techathome my gps not match to the prot! I want to use internal compass. whow can i use??
If your APM board having inbuilt Compass this method in the video will work, otherwise I think you have to use external only
still having the problem even after using the jumper
The you have to use external compass that comes with GPS module
This is not happening, brother
Give me one solution......brother.....please.........
I did these procedures, but unfortunately without success I don't know what else to do
There are lot of fake boards available in the market, I think in your APM there is no compass.
You can connect external compass that comes with GPS module
Refer this: ua-cam.com/video/jHaYAA_Km7Y/v-deo.html
@@techathome hi i'm have apm 2.8 and i have the same problem as you but after adding the jumper nothing changed
What should I do?
You can use the external compass, that comes with GPS module
@@techathome hi, I used an external compass, that was not the problem. But the reason was that I used the i2c port for that connection.
Bro I have mounted external gps but the dots are not seen.....
And it's showing No fix
You have to connect both GPS and Compass ports.
Have you Connected external compass port??
Also you have to check mark on external compass option?
@@techathome yeah
@@techathome should connect it in the old gps port... Or the new gps port
@@techathome I have selected apm and external compass
No it's not working i tried please help
Then you have to use external compass that comes with GPS module.
Not working....
Bro i did that but dots are not show
Some APM board will be not having onboard compass, this might be the issue with you I think
So how to solve this problem i have external compass also but it didn't recognized by the board
Plug your external Compass to the port under the GPS Port.
In Compass calibration check mark on external compass option and try
I don't know exactly , but for some people I had told the same above steps for using external compass, It had worked
After connection dot is not apear
Then your board is not having Compass , I think
It is new APM 2.8.0 board
Some board will not have, if possible replace and try once.
not help AT ALL!!!