I think that NEED is a relative term... of COURSE you NEEDED it! That's gonna be an AWESOME machine! I'm looking for one myself! I look forward to seeing you use that beast!
" you NEEDED it! That's gonna be an AWESOME machine ", agreed. For the amount you payed vs the condition its in, i'd say it worth putting a hydraulic thumb on it. Heck you might become the new LD18 of Pennsylvania with that machine. 😎
Hey get back to working on that fork lift wheel loader. Lol. Just kidding love your channel. This channel your channel and Andrew's are by far my most favorite channels on UA-cam
Its going to look great all cleaned up. The better deal is never the one listed. The things I've gotten from simply saying, "so, what else you got for sale?"
It always seems like the really huge ones are cheaper than the little ones. Like the free, giant loader was that way too. Maybe because they are hard to haul? or they intimidate DIY people? where bigger companies want newer? to depreciate etc?
@@alan6832 the number of people that can invest “maybe money” on an excavator are limited when the units get bigger. It means that it is an operator level person with resources to haul, store, perform repairs, and find enough “make work” projects for while getting the machine into production level fitness.
It’s mainly all of what Alan said, most are afraid to mess with the bigger stuff, plus some don’t care to fool with it because they are afraid of the abuse it could have gone through too.
The relief on the hydraulic tank is so you don't take a bath when you change the filter or have to open it up for whatever reason. That's a damn fine machine my friend. Can't wait to see it on a project.
@@SuperZylar Yepper. Cavitation will destroy a pump quicker than anything else. Even with gear pumps, each tooth creates a low pressure area on the back side. Heck water boils at room temperature under a vacuum, yet in a nuclear reactor, despite seeing temps way above 212°, the high pressure raises the boiling point so far it won't boil. It's pretty wild really.
@@pamike4873 I believe I've heard from salesman that a pressurized system helps keep down dust/water ingress. If it wasn't sealed it would breathe a bit in and out correlating to temp going up and down. Even when its sitting. About nuclear reactors, I saw on a documentary about types of reactors, some run up to 600-800° f, but don't boil because it's under so much pressure. Same reason why car coolant loops are run pressurized, to increase the boiling point. Totally different kettle of fish as to why a ex reservoir runs pressurized. I never thought of it decreasing cavitation, but makes sense.
Mitsubishi engines are great, they will last at least 20.000 hours when maintained. This one seems to be, and it starts great. Dont forget to change out the swing oil. Water will get in the bottom of it and ruins the lower bearing. Especially when it has been sitting for a while. All in all plenty of life left in her. Another 6000 hours is no exeption. Maybe get the hydraulic oil tested so you dont have to replace all of it, maybe half of the capacity of the tank is enough since it doesnt seem discolored. Saves you some $. Oil gets expensive pritty quick. Company i work for doesnt even bother changing hydraulic fluid. Since the hydraulic tank is under some presssure the oil doesnt "wear out" as quick as normal
@@megape95 Absolutely. This excavator having less than 7,000 on it will last Matt forever. Unless he starts his own excavation company with me, that is. Then the hours go by pretty quick, lol.
I use to work for Kobelco in Calhoun Ga where they built the excavators from 2003 to 2009. I set the swing motors and built the small valves ,control valves for them. The pressure release valve on the hydraulic tanks was used when you lowered the boom down to the ground for changing the hydraulic hoses out .. it helped to relieve some of the pressure off the lines
The exhaust manifolds on those Mitsubishi engines are known for cracking like that, other than that they're pretty bulletproof. Same engine was used in Mitsubishi medium trucks and you'll kill the rest of the truck before you kill the engine, just make sure to get yourself some metric tools before you try to work on it, all metric fasteners same as a Yanmar.
@@larrywalker7759 FYI. I have more than a few 10mm, I keep it by default on my drives I have found more than couple 10mm, that I lost. Randomly, a couple of 8mm down the battery box void, I also have the GM battery tool.
Looks like a decent running machine, preetty quick, a good buy! Don't forget you have the pin grabber coupler, you can reverse the bucket and scoop forward like a shovel.
I’d say that the first upgrade after you do the necessary maintenance and repair should definitely be a thumb. I’ve always felt that excavators are a bit useless without one lol. Excellent find.
A Thumb! Matt, exhaust manifolds usually crack from high exhaust temps. On a charge cooled engine, look at the charge pipes/clamps, cooler and intake manifold area for leaks. Newer engines use a ductile iron for the exhaust manifolds. Even using Ni rod, the casting will crack again right next to the repair. Best bet is new. Nice score!
Looks like you found yourself a "sweet" purchase, Matt !! I was impressed with what you managed to find WITHOUT the repairs needed !! Best wishes to you, Matt - hope you can make some money with that machine, Buddy !! You deserve it !!
This particular video is one that I have been patiently waiting to see for a while now! I am stoked for you Matt! It was quite the deal of the day; especially considering it came with all that it did. I said to myself “I wish he had that when he was clearing/grubbing the area for his new shop” and of course, shortly after I heard you say it! Now it’s time to get that truck and trailer combination up and running to haul all that machinery around. Enjoy it brother; take care.
It is like watching one of those hoarder estate cleanups where you wonder how the hell a dude could wind up with so much wacky stuff after 40 years. Except you get to see it happen step by step on this channel.
@@SurvivalSchoolHouse oh if your looking for that content go look up musty1 his stuff gets super odd. And his part store sesames be thouses of junked engines in way too many different hordes.
@@Doitgood52 I have concerns when I saw drone footage over the mountaintop that Andrew bought recently. It is starting to look like an equipment yard where one doesn't belong.
Nice Matt, that is going to be a great asset. One recommendation, get that exhaust fixed before you use it too much, especially in winter. You don't want to suck any cold air in on shutdown and have it come across those nice hot valves. Looks like the hydraulics operate very smoothly. Makes life much easier. I can't believe you actually got that for the price. Would be nice to add a good thumb. Congrats.
Nice find. Degreaser and a hot water pressure washer. Use a 2:1 paint thinner - boiled linseed oil mix and spray or brush on then wipe with a paper towel and the paint will look like new. A new seat or at least a new cover will make for a much nicer cab.
Well Matt, another awesome piece of equipment added to your arsenal! Look forward to you getting her serviced and shined up for work. I'm confident she'll pay some big dividends down the road with future work and home/shop projects!
It was cool watching the excavator tracking in high speed, I wish they had a road gear like that sometimes. Now that you and Bradley are done clearing land, you get a big excavator lol. Besides sitting for a while, it seems like the previous owner cared about it.
Hi Matt, I’m impressed with the purchase. You will be surprised how much work you can do with this machine having the ground weight etc and the extra power. A thumb will be a good addition. I look forward to you working this machine to pay its keep. Bravo from Victoria Australia
I worked construction from the 80's to retirement. I once saw an operator hammering a stake in the ground at the limit of his boom and did it so gently the man holding the stake never had to take his hand off.
I used to work at Precision Steel &Welding, a steel fabrication company in Siler City, N. Carolina from 1990 to 2001. I was a press brake operator and bent the angles on steel plates for Kobelco and other excavator brands. We made excavator dog houses that hold the rollers on the non- dirt-touching side of the bottom of the tracks. I also bent boom and bucket parts. The hydraulic tank has a pressure relief valve so you can release the pressure when you do a greasing service. The hydraulic tank builds pressure from the hydraulic oil getting hot and expanding plus heating the air inside the hydraulic tank, as air is heated it expands creating pressure. Love your videos. They are never boring. lots of variety.
When I was driving these types of machines, they used to weld bits of old cutting edges to the bottom of the buckets to extend the life of them, being a strong point for wear, they need it on old buckets.
That is a good deal! I was thinking you were going to say 20 to 25 or so, after you get her serviced all she needs is a thumb to complete it for doing even more work.
Nice buy. I've always thought you needed a bigger excavator. When you operate them it's like poetry in motion your so smooth like an extension of your arm. It's fun to watch.
Kobelco's are great excavators, you got a heck of deal on that unit. It looks to have been used hard but maintained. A little TLC ought to have it sorted out in no time. The Mitsu 6d-34T is a great engine actually their only weak spot is the exhaust manifolds. I would just get a new manifold as they can be impossible to weld as the cast used is full of crap so it is a real crap shoot if you will be able to weld it and get it to last.. There are lots of low-cost aftermarket knock-offs for that engine since it was used worldwide so finding one should not be too hard..
All I can say Matt is you must have a very understanding wife lol. My late wife would go mad if I purchased a new power drill let alone an excavator lol 😂
@@clypeum5063 sadly she passed away a couple of years ago and even as she was laid close to passing she still managed to make jokes about my power tools lol.... She wanted a pressure washer to clean her car and thought you just attached the hose an off you go. She didn't realise it had to be switched on bless her.... Loved her for her gooky mistakes lol....
Man Matt, that looked like it was fun to operate. Good score! BTW, thanks for FINALLY stating in the video how much you paid for it. I'm not into big equipment so I do not know what is a good deal or a crap deal. You are giving me a good education. Thank you!
It does indeed look like you scored with this one. Also, we're glad you added the bonus footage so we could see you guys were OK after the ice storm. Here's hoping there won't be any more storms this year!
I've got to believe that this is your best purchase to date for price, condition and usefulness. Knowing your wife's reaction to your past purchases and how intelligent she is, I think she would have knocked you out if you had passed up this deal. It's kinda refreshing to know that the rehab will be minimal and we'll get to see you using it more in short order, even though we love the rehabs as much as anything. Can't wait to hear that repaired manifold make her purr.
Flipping OUTSTANDING PURCHASE at a great price. This machine will serve you well with a little love. I've watched all of your videos, all the jobs you've done that would've been a piece of cake with that machine in the fleet!!! I'm sure there will be more now. Keep up the great videos
hello matt love the videos here in uk i am a excavator op myself just letting u know the pressure release valve on the hydraulic tank is so when u release a hose or need to work on the system it doesn't blow off when u take a hose or fitting off that all its for many thank for great content cant wait to see then new shop
Really nice purchase Matt! Although the sound of the engine seems very strange due to that broken manifold, the machine is likely to give you a lot of profit for some years!!
Great SCORE!! YOU seem to be in the right places, at the right times, asking the exact right questions!!! Now, all you need to do is be in the right locations, doing all the right things, & Ms. Eva will be even happier than she's ever been!!!
Thank you Matt love the videos the only sad part is I’ve watched every video on the channel so I am required to wait till you come out with a new one😂🤷♂️ not a bad thing though
I can’t wait to see all the videos replacing the exhaust manifold, cleaning it up real good on the inside and out, hammering all the big dents out, replacing rubber seals, all the filter and fluid changes that need changing, etc. Looks like it’ll be a good series!! 😎👍🏻🚜
Oh and if I can add, the Mitsibushi (similar to Korean Hyundai) engines are "bullet-proof", they are reliable robust, well-engineered low maintenance units.
Man I would have a absolute blast cleaning that cab. OCD satisfaction guaranteed. Edit: After bending that hydraulic pump door straight I would personally strengthen it. It looks like you can bend it by just yanking it open. (Especially if the hinges are a bit seized).
Machines sitting for years unused at job sites is a common thing. I think some construction firms leave them there to collect payment for " being on the jobside" even tho the project got delayed for whatever reason. Sadly this also attracts some unwanted guests and vandalism that probably lead to that smashed window... 16:00 I count 15 factory warning stickers on that window, there must be a worker on the assembly line who does nothing else all day then to glue these on there :)
The bucket on the back of your truck really put this thing into perspective! What a unit! Congrats on the purchase, can't wait to see what you do with it! 😁
Hi Matt, listening to that beast through my headphones, that motor sure sounds very strong, I hope it is,, best of luck. You are one of the channels I watch regularly!!
Nice "new" shovel you've got there, Matt! I think she'll clean up really nice and with the work that you mentioned that you need to do to bring her up to job ready, you'll have a machine that should give you years of service. I'm happy for you, my friend! I hope that you didn't get into any trouble with the Mrs. for purchasing the new tool...😏
Hubby and I are so excited for your "find". We comment as we watch how great of a job you do as you work. You are a great guy and we enjoy watching all of your projects. Your enthusiasm and joy in the work you do on any size machine you get to work is fun to watch. That was a great buy for you!!!
Matt, that's a pretty nice older machine. 7,000 hours ....it still has many hours left in it and the undercarriage will last a long time for you as much as you'll use it. A good detail inside the cab, a seat cover and some paint/body work and you'll be styling. When you paint it, use an airless paint sprayer. I used to paint cranes for Lampson International (crane company) and that is the way to go. More paint material on the machine and WAY faster. I have ran mostly Cat equipment in my career, but I had a favorite loader and it was a old Kobelco and I loved it. It had a single joystick bucket control unlike the Cats with the double levers for the bucket. It would start immediately in the coldest condition no matter what where the Cats were harder starting. I think you made a nice purchase there! You stole that for $16K in my opinion. First thing, I would replace the manifold ASAP. A thumb, a full service, about 6 or 8 gallons of industrial equipment paint and a manifold and you'll be set! You're a very smart, well driven young man with a bright future ahead of you! You're one of my favorite UA-camrs for sure. Love your humor!
He mine also. Matt is a go getter. Unfortunately here lately he has been a go getter something else like parts 😂. I hope he get a ton of hours out of this one…
In the vintage/antique shaving community we called it RAD or SCAD or Razor Acquisition Disorder or Shaving Cream Acquisition Disorder. Obviously Matt has a bit of HEAD.🙂
Love this intro: Prestige Pond by Semi Villains with resonator gives this channel a folksy feeling. That long trek onto your property, geez how long did that take? I'm wondering if it took as long as the drive from the owner to your drive? I really like coming here and watching you cobble things together like a REAL farmer, but this feels all tingly warming the cockles of my heart seeing something like this turn out for you. Thanks for bringing us constant content.
Wow, Matt! What a great deal this was! I'm so glad that you found it before Dirt Perfect or Andrew snatched it up! I sure hope this excavator keeps you smiling for many, many years. I sure wish I lived closer so I could help you clean out that cab. Gonna be a beauty when it's all cleaned up. Congrats!!!!
Great video! I felt like I was 12 years old again watching a skilled operator working! This machine would have come in REAL handy for that barn and silo demo job some months ago! Congratulations on what looks like a SCHWEET SCORE!
Kobelco is a great excavator, nice hydraulics and smooth operated, almost never any leaks of oils or hydraulics. Its precision built with good quality gaskets and nice surface fittings. Great find!
I wouldn’t mind a machine like that. I betting you will never regret the purchase of that machine. I am happy for you sir, good purchase and nice addition to the fleet.
Hi Matt. It looks like you got yourself a bargain machine that needs a bit of TLC and cleaning. I look forward to seeing more episodes of it working once you get it fully serviced and check out the loose pins and bushes, and you guys get out of winter. Kind regards, Dave from New Zealand.
Matt, great buy...Christine is gonna feel neglected, no telling what she might do. She is one machine that not many people know how to operate and I would like to see her moving dirt !
Matt I really love watching your projects all you do to them. I don't have any experience with operating heavy equipment but I enjoy watching you work on them and getting them running when they have been setting for years. I recently had a partial knee replacement and found you on here and have been hooked. Can't wait for the next video. Keep on rescuing and reviving . Mid Tenn fan
Congratulations on your new Excavator! That is Awesome! Now you should look for a M35A2 Deuce and a Half or something similar to add to your collection of cool equipment. It will help pull this excavator around town. Thanks again for sharing with all of us Matt.
Hell yeah! That thing is sweet!!! Looks very good, can’t wait to see it get all cleaned up and maintained. Your channel just rocketed up to most looked forward to watching now!
Sometimes good things happen to good people. Been a sub for quite some time. I just sat here with a big grin on my face when I saw what you got. Thanks for the videos.
These are great machines, I'm a dealer tech so I know them well, not sure if it's a ore or post minor change -6 machine. Pre minor machines have fewer buttons on the dash, unless it's been replaced. The other indicator is if there's a grommet on the controller.
Perfect Saturday morning video - I love seeing other people get a good deal and getting excited about putting something back in good shape! Matt, I always enjoy your great attitude and tenacity to get anything needed done - very motivational. Keep the great videos coming. I need to head out to my shop now - lol!
Enjoyed the show, I'm 58 but you crazy adventures are still inspiring. Just did what I should of done a long time ago and subscribed. Hope you find some rims for Christine.
Wow, awesome deal! I’ve been looking for months now and can’t find any kind of deal remotely that good, you did great! Also, we gotta get a thumb on that thing, looking forward to more vids on this machine!
What a deal! For the price that machine is incredible, the cold start sounded great. Those 6 cyl Mitsubishis are super strong, it will definitely pay for itself
That’s a steal for the record book…you’ve got room for lots of repairs & upgrades & you’ll still be in it “right”! Sometimes it simply right place at the right time & & having the cash does certainly help too. I’ve been looking at these for a while myself & Im heartened to see there are still good deals out there.
Old Mitsu engines are fantastic. years ago my sister had an older used Hyundai she got and it had a Mitsubishi engine they were using back then, I was delighted. yours is even better.
I enjoyed this one, you do a great job with your videos. When I see a new one pop up I watch them right away. Good looking machine, you should get a lot of work of that excavator.
You definitely scored a gem in that Kobelco, Matt! Lots of deep TLC and she'll be a long term winner for you. Definite pressure wash everywhere and spit and polish, she'll look great! Looking forward to your maintenance video on her. Spring's a comin' ready for pressure wash season! She's a keeper...👍👍
Hi matt, Your purchase with the Kobelco Excavator seems a super good investment. Everything seems to function entirely properly. I think you as soon as the weather permits you should start with a high pressure cleaning so that you can see the condition of the paint well and the machine will need some major maintenance but that is entrusted to you. On behalf of my wife WIlleke we send you and Debra Lynn lots of love from the Netherlands
I think that NEED is a relative term... of COURSE you NEEDED it! That's gonna be an AWESOME machine! I'm looking for one myself! I look forward to seeing you use that beast!
I agree with you. You have a great channel also. Looking forward to your next upload!
" you NEEDED it! That's gonna be an AWESOME machine ", agreed. For the amount you payed vs the condition its in, i'd say it worth putting a hydraulic thumb on it. Heck you might become the new LD18 of Pennsylvania with that machine. 😎
Of course you need for content to get more views to buy more toys
What happed to your traxcavator? It stopped at part 18.
Hey get back to working on that fork lift wheel loader. Lol. Just kidding love your channel. This channel your channel and Andrew's are by far my most favorite channels on UA-cam
Its going to look great all cleaned up. The better deal is never the one listed. The things I've gotten from simply saying, "so, what else you got for sale?"
And some times little pushes in that direction help or just letting them talk things out help too. I have come across way better deals that way also.
It always seems like the really huge ones are cheaper than the little ones. Like the free, giant loader was that way too. Maybe because they are hard to haul? or they intimidate DIY people? where bigger companies want newer? to depreciate etc?
@@alan6832 PLUS WHERE THE HECK ARE YOU GONNA STORE A MONSTER LIKE THAT?
@@alan6832 the number of people that can invest “maybe money” on an excavator are limited when the units get bigger. It means that it is an operator level person with resources to haul, store, perform repairs, and find enough “make work” projects for while getting the machine into production level fitness.
It’s mainly all of what Alan said, most are afraid to mess with the bigger stuff, plus some don’t care to fool with it because they are afraid of the abuse it could have gone through too.
You can almost feel a machine purring with satisfaction at being useful again.
That’s a great find Matt. I’ve been looking for one myself, but not quite that big. Thanks for sharing.
Wow the cab has windows!!! The trac stayed on, no hoses blew off and it runs!!!! I’d say you did great!
RIGHT?!?!? weird!
SHHHHH! It'll hear you! 😂
Yes and no squealing belts!!!!!!!!!!!!!!!
@@okiekidd6091 But is has a huge exhaust leak. Mandatory for Diesel Creek equipment.
@@1959sdl Very true thanks for pointing that out. Have a good day!!!!!!!!!!!!!!
The relief on the hydraulic tank is so you don't take a bath when you change the filter or have to open it up for whatever reason. That's a damn fine machine my friend. Can't wait to see it on a project.
yep, and the sleight over pressure in the tank keeps it from cavitation the pump.
@@SuperZylar Yepper. Cavitation will destroy a pump quicker than anything else. Even with gear pumps, each tooth creates a low pressure area on the back side. Heck water boils at room temperature under a vacuum, yet in a nuclear reactor, despite seeing temps way above 212°, the high pressure raises the boiling point so far it won't boil. It's pretty wild really.
@@pamike4873 I believe I've heard from salesman that a pressurized system helps keep down dust/water ingress. If it wasn't sealed it would breathe a bit in and out correlating to temp going up and down. Even when its sitting.
About nuclear reactors, I saw on a documentary about types of reactors, some run up to 600-800° f, but don't boil because it's under so much pressure. Same reason why car coolant loops are run pressurized, to increase the boiling point. Totally different kettle of fish as to why a ex reservoir runs pressurized. I never thought of it decreasing cavitation, but makes sense.
Mitsubishi engines are great, they will last at least 20.000 hours when maintained. This one seems to be, and it starts great. Dont forget to change out the swing oil. Water will get in the bottom of it and ruins the lower bearing. Especially when it has been sitting for a while. All in all plenty of life left in her. Another 6000 hours is no exeption. Maybe get the hydraulic oil tested so you dont have to replace all of it, maybe half of the capacity of the tank is enough since it doesnt seem discolored. Saves you some $. Oil gets expensive pritty quick. Company i work for doesnt even bother changing hydraulic fluid.
Since the hydraulic tank is under some presssure the oil doesnt "wear out" as quick as normal
@@megape95 Absolutely. This excavator having less than 7,000 on it will last Matt forever. Unless he starts his own excavation company with me, that is. Then the hours go by pretty quick, lol.
I use to work for Kobelco in Calhoun Ga where they built the excavators from 2003 to 2009. I set the swing motors and built the small valves ,control valves for them. The pressure release valve on the hydraulic tanks was used when you lowered the boom down to the ground for changing the hydraulic hoses out .. it helped to relieve some of the pressure off the lines
Congratulations on your new machine Matt , after you get it cleaned up and serviced , it will be nice to see you working it !! Stay safe and warm !!
The exhaust manifolds on those Mitsubishi engines are known for cracking like that, other than that they're pretty bulletproof. Same engine was used in Mitsubishi medium trucks and you'll kill the rest of the truck before you kill the engine, just make sure to get yourself some metric tools before you try to work on it, all metric fasteners same as a Yanmar.
Pretty sure Matt has all the Metric tools by now except a 10mm socket, and every mechanic in the world is missing a 10mm socket.
All things are metric. my 2000 taurus, my 2006 brother of yours f250. All metric. 36mm socket for f250 fuel filter. I drove for Pepsi for 24yrs.
@@larrywalker7759 FYI. I have more than a few 10mm, I keep it by default on my drives I have found more than couple 10mm, that I lost. Randomly, a couple of 8mm down the battery box void, I also have the GM battery tool.
@@larrywalker7759 yeah I've had to replace more than a few 10mm sockets before today. 🤣
We've had Kobelco Crawler Cranes for over 20 Years, and although they have a easier life than excavators, they are bullet proof.
A m8 in the UK supplies parts and wrecks Kobelco diggers.
Looks like a decent running machine, preetty quick, a good buy! Don't forget you have the pin grabber coupler, you can reverse the bucket and scoop forward like a shovel.
Your videos never fail to amaze me! Between your skills and the capabilities of your machines truly fascinate me.
I’d say that the first upgrade after you do the necessary maintenance and repair should definitely be a thumb. I’ve always felt that excavators are a bit useless without one lol. Excellent find.
Doesn't letsdig18 have his own brand of thumbs?
Well said
aren't we all?
Ive got 2 myself, Ive found them to be pretty useful, typing this out would be so much harder without them
thumb is useless, get a rototilt and be done with this
A Thumb! Matt, exhaust manifolds usually crack from high exhaust temps. On a charge cooled engine, look at the charge pipes/clamps, cooler and intake manifold area for leaks. Newer engines use a ductile iron for the exhaust manifolds. Even using Ni rod, the casting will crack again right next to the repair. Best bet is new. Nice score!
Matt, I second the addition of a very useful Thumb.
Looks like you found yourself a "sweet" purchase, Matt !! I was impressed with what you managed to find WITHOUT the repairs needed !! Best wishes to you, Matt - hope you can make some money with that machine, Buddy !! You deserve it !!
This particular video is one that I have been patiently waiting to see for a while now! I am stoked for you Matt! It was quite the deal of the day; especially considering it came with all that it did. I said to myself “I wish he had that when he was clearing/grubbing the area for his new shop” and of course, shortly after I heard you say it! Now it’s time to get that truck and trailer combination up and running to haul all that machinery around. Enjoy it brother; take care.
It is like watching one of those hoarder estate cleanups where you wonder how the hell a dude could wind up with so much wacky stuff after 40 years. Except you get to see it happen step by step on this channel.
Lol, spot on, I love it!
@@SurvivalSchoolHouse oh if your looking for that content go look up musty1 his stuff gets super odd. And his part store sesames be thouses of junked engines in way too many different hordes.
Played any squash lately Philo? Hows Clyde doing these days?
Ha! Andrew Camarata is a great example of that.. but his stuff ALL WORKS! He only sells cranes that fall over cliffs 😂🤣
@@Doitgood52 I have concerns when I saw drone footage over the mountaintop that Andrew bought recently. It is starting to look like an equipment yard where one doesn't belong.
Nice Matt, that is going to be a great asset. One recommendation, get that exhaust fixed before you use it too much, especially in winter. You don't want to suck any cold air in on shutdown and have it come across those nice hot valves. Looks like the hydraulics operate very smoothly. Makes life much easier. I can't believe you actually got that for the price. Would be nice to add a good thumb. Congrats.
I’m jealous I want one!! But super happy for you buddy
The pressure washing Video was amazing on this Rig Matt 18:27 @Diesel Creek
Matt is living the dream for sure! Thanks for all the great content. We are All looking forward to the new shop build.
You and me both!
Nice find. Degreaser and a hot water pressure washer. Use a 2:1 paint thinner - boiled linseed oil mix and spray or brush on then wipe with a paper towel and the paint will look like new. A new seat or at least a new cover will make for a much nicer cab.
Great buy Matt! This will be a "go to" machine, that's for sure! Love it.
Well Matt, another awesome piece of equipment added to your arsenal! Look forward to you getting her serviced and shined up for work. I'm confident she'll pay some big dividends down the road with future work and home/shop projects!
Qq😊
It was cool watching the excavator tracking in high speed, I wish they had a road gear like that sometimes. Now that you and Bradley are done clearing land, you get a big excavator lol. Besides sitting for a while, it seems like the previous owner cared about it.
You could call it "Swampy" or "Georgia"
Wide tracks and moss everywhere.
Definitely Swampy!
@@andrewclarkehomeimprovement Or Elsie perhaps?
It was built in Georgia so that works for a name.
Hi Matt, I’m impressed with the purchase. You will be surprised how much work you can do with this machine having the ground weight etc and the extra power. A thumb will be a good addition. I look forward to you working this machine to pay its keep. Bravo from Victoria Australia
Michael Cameron: Yeah, I was just thinking, "That Hoe needs a thumb".😝
I worked construction from the 80's to retirement. I once saw an operator hammering a stake in the ground at the limit of his boom and did it so gently the man holding the stake never had to take his hand off.
I used to work at Precision Steel &Welding, a steel fabrication company in Siler City, N. Carolina from 1990 to 2001. I was a press brake operator and bent the angles on steel plates for Kobelco and other excavator brands. We made excavator dog houses that hold the rollers on the non- dirt-touching side of the bottom of the tracks. I also bent boom and bucket parts.
The hydraulic tank has a pressure relief valve so you can release the pressure when you do a greasing service.
The hydraulic tank builds pressure from the hydraulic oil getting hot and expanding plus heating the air inside the hydraulic tank, as air is heated it expands creating pressure. Love your videos. They are never boring. lots of variety.
When I was driving these types of machines, they used to weld bits of old cutting edges to the bottom of the buckets to extend the life of them, being a strong point for wear, they need it on old buckets.
That is a good deal! I was thinking you were going to say 20 to 25 or so, after you get her serviced all she needs is a thumb to complete it for doing even more work.
Nice buy. I've always thought you needed a bigger excavator. When you operate them it's like poetry in motion your so smooth like an extension of your arm. It's fun to watch.
Kobelco's are great excavators, you got a heck of deal on that unit. It looks to have been used hard but maintained. A little TLC ought to have it sorted out in no time. The Mitsu 6d-34T is a great engine actually their only weak spot is the exhaust manifolds. I would just get a new manifold as they can be impossible to weld as the cast used is full of crap so it is a real crap shoot if you will be able to weld it and get it to last.. There are lots of low-cost aftermarket knock-offs for that engine since it was used worldwide so finding one should not be too hard..
I second the call for a NEW exhaust manifold. Less grief all round.
Best wishes from the far North.
Really nice sized machine, did he say the $?
I'm thinkin 20-25k would be a dam good price in that condition?
@@jaylast1958 $16,000 - winner!
Exhaust manifolds are common issue on all Mitsu products, their cars suffer cracking issues too, replaced quite a few over the years.
Shoot, a little flex seal with fix that crack right up 🤣 😂.
All I can say Matt is you must have a very understanding wife lol. My late wife would go mad if I purchased a new power drill let alone an excavator lol 😂
might have to get here something nice too next time ;) Or involve her in the fun like Matt with the Jeep!
clypeum his LATE wife….
@@clypeum5063 sadly she passed away a couple of years ago and even as she was laid close to passing she still managed to make jokes about my power tools lol.... She wanted a pressure washer to clean her car and thought you just attached the hose an off you go. She didn't realise it had to be switched on bless her.... Loved her for her gooky mistakes lol....
@@krissswanson its cool bud, he probably didn't notice 👍
My wife told me that if I bought one more excavator she was going to leave me. I sure hated to see her go.
Man Matt, that looked like it was fun to operate. Good score! BTW, thanks for FINALLY stating in the video how much you paid for it. I'm not into big equipment so I do not know what is a good deal or a crap deal. You are giving me a good education. Thank you!
It does indeed look like you scored with this one. Also, we're glad you added the bonus footage so we could see you guys were OK after the ice storm. Here's hoping there won't be any more storms this year!
Trust me Matt that excavator is gonna make life a lot easier if not more money, keep at it bro.
alot more fun to
I've got to believe that this is your best purchase to date for price, condition and usefulness. Knowing your wife's reaction to your past purchases and how intelligent she is, I think she would have knocked you out if you had passed up this deal. It's kinda refreshing to know that the rehab will be minimal and we'll get to see you using it more in short order, even though we love the rehabs as much as anything. Can't wait to hear that repaired manifold make her purr.
Yeah, I like the repairs too.
@@stuwest5862 16K
The words “body work” and “5lb hammer” always work well together
Flipping OUTSTANDING PURCHASE at a great price. This machine will serve you well with a little love.
I've watched all of your videos, all the jobs you've done that would've been a piece of cake with that machine in the fleet!!! I'm sure there will be more now. Keep up the great videos
A seat cover, bucket of water and a quick paint job & she'll be good as new.
Well it needs a lot more than that.
@@norsevikingsir4932 Well, maybe a wipe down with an oily rag...
It will need to be a huge bucket of water
hello matt love the videos here in uk i am a excavator op myself just letting u know the pressure release valve on the hydraulic tank is so when u release a hose or need to work on the system it doesn't blow off when u take a hose or fitting off that all its for many thank for great content cant wait to see then new shop
Really nice purchase Matt! Although the sound of the engine seems very strange due to that broken manifold, the machine is likely to give you a lot of profit for some years!!
Great SCORE!! YOU seem to be in the right places, at the right times, asking the exact right questions!!! Now, all you need to do is be in the right locations, doing all the right things, & Ms. Eva will be even happier than she's ever been!!!
Thank you Matt love the videos the only sad part is I’ve watched every video on the channel so I am required to wait till you come out with a new one😂🤷♂️ not a bad thing though
Same here lol
I watched most 2 times!
Same 😀
Matt’s the man!
Glad you like them!
I can’t wait to see all the videos replacing the exhaust manifold, cleaning it up real good on the inside and out, hammering all the big dents out, replacing rubber seals, all the filter and fluid changes that need changing, etc. Looks like it’ll be a good series!! 😎👍🏻🚜
@DoubleJ It might be a "great" series!
What a great machine for way fewer bucks than folks want for well used compact tractors! Looking forward to the bodywork and TLC episodes.
Was just thinking I hadn't watched one of your videos for a while and noticed this in my feed, great stuff! Every man wants a big excavator.
Oh and if I can add, the Mitsibushi (similar to Korean Hyundai) engines are "bullet-proof", they are reliable robust, well-engineered low maintenance units.
Man I would have a absolute blast cleaning that cab.
OCD satisfaction guaranteed.
Edit: After bending that hydraulic pump door straight I would personally strengthen it.
It looks like you can bend it by just yanking it open. (Especially if the hinges are a bit seized).
Amazing! Can’t wait for the next video on this one! Keep up the good work.
I've been whaching your vidoes for 2 years now and each video gets better every time
Machines sitting for years unused at job sites is a common thing. I think some construction firms leave them there to collect payment for " being on the jobside" even tho the project got delayed for whatever reason. Sadly this also attracts some unwanted guests and vandalism that probably lead to that smashed window...
16:00 I count 15 factory warning stickers on that window, there must be a worker on the assembly line who does nothing else all day then to glue these on there :)
The bucket on the back of your truck really put this thing into perspective! What a unit! Congrats on the purchase, can't wait to see what you do with it! 😁
No kidding. Doesn't look like much on the ground with nothing next to it for scale, but dang that's a heck of a bucket
Put a thumb on it, clean it, n Shazam!
Watching the truck spring’s come back up, when he picked the bucket off truck tell s whole story!
I love the Big toys!
Hi Matt, listening to that beast through my headphones, that motor sure sounds very strong, I hope it is,, best of luck. You are one of the channels I watch regularly!!
Nice "new" shovel you've got there, Matt! I think she'll clean up really nice and with the work that you mentioned that you need to do to bring her up to job ready, you'll have a machine that should give you years of service. I'm happy for you, my friend! I hope that you didn't get into any trouble with the Mrs. for purchasing the new tool...😏
I’m almost disappointed it’s in such a good shape, gotten used to all your awesome resto vids😂
Seriously, congrats on a great machine!
Hubby and I are so excited for your "find". We comment as we watch how great of a job you do as you work.
You are a great guy and we enjoy watching all of your projects. Your enthusiasm and joy in the work you do on any size machine you get to work is fun to watch.
That was a great buy for you!!!
Thanks!
Congratulations Matt on new excavator, will be looking forward to seeing it in your up coming videos, its a big boy.
Fun listening to DP's podcast with you Matt..i have enjoyed your channel almost 2 years now👍🏻🍺
Matt, that's a pretty nice older machine. 7,000 hours ....it still has many hours left in it and the undercarriage will last a long time for you as much as you'll use it. A good detail inside the cab, a seat cover and some paint/body work and you'll be styling. When you paint it, use an airless paint sprayer. I used to paint cranes for Lampson International (crane company) and that is the way to go. More paint material on the machine and WAY faster. I have ran mostly Cat equipment in my career, but I had a favorite loader and it was a old Kobelco and I loved it. It had a single joystick bucket control unlike the Cats with the double levers for the bucket. It would start immediately in the coldest condition no matter what where the Cats were harder starting. I think you made a nice purchase there! You stole that for $16K in my opinion. First thing, I would replace the manifold ASAP. A thumb, a full service, about 6 or 8 gallons of industrial equipment paint and a manifold and you'll be set! You're a very smart, well driven young man with a bright future ahead of you! You're one of my favorite UA-camrs for sure. Love your humor!
He mine also. Matt is a go getter. Unfortunately here lately he has been a go getter something else like parts 😂. I hope he get a ton of hours out of this one…
Mat wot you going to with it
The "Equipment buying Disease" is strong with this one. Had to track it past the wheel-less unfinished grader? Lol
waiting on parts for her 😥
Just busting yer balls 😄. Nice machine! Impressive swing speed. At that price you basically stole it
In the vintage/antique shaving community we called it RAD or SCAD or Razor Acquisition Disorder or Shaving Cream Acquisition Disorder. Obviously Matt has a bit of HEAD.🙂
@@DieselCreek just think if the grader was done you could use it to plow the snow off the driveway
Love this intro: Prestige Pond by Semi Villains with resonator gives this channel a folksy feeling. That long trek onto your property, geez how long did that take? I'm wondering if it took as long as the drive from the owner to your drive?
I really like coming here and watching you cobble things together like a REAL farmer, but this feels all tingly warming the cockles of my heart seeing something like this turn out for you. Thanks for bringing us constant content.
The engine actually sounds pretty good once you get past that exhaust leak. 😎👍 cool find!
Wow, Matt! What a great deal this was! I'm so glad that you found it before Dirt Perfect or Andrew snatched it up! I sure hope this excavator keeps you smiling for many, many years. I sure wish I lived closer so I could help you clean out that cab. Gonna be a beauty when it's all cleaned up. Congrats!!!!
Great video! I felt like I was 12 years old again watching a skilled operator working! This machine would have come in REAL handy for that barn and silo demo job some months ago! Congratulations on what looks like a SCHWEET SCORE!
Kobelco is a great excavator, nice hydraulics and smooth operated, almost never any leaks of oils or hydraulics. Its precision built with good quality gaskets and nice surface fittings. Great find!
Good Saturday afternoon watch Matt, thanks for sharing. That cold start is a winner!! You lucked out.
I wouldn’t mind a machine like that. I betting you will never regret the purchase of that machine. I am happy for you sir, good purchase and nice addition to the fleet.
We have an identical one at work with 13,350 hours on it going strong...them Mitsubishi 6 cylinders are great man
Hi Matt. It looks like you got yourself a bargain machine that needs a bit of TLC and cleaning. I look forward to seeing more episodes of it working once you get it fully serviced and check out the loose pins and bushes, and you guys get out of winter. Kind regards, Dave from New Zealand.
Matt, great buy...Christine is gonna feel neglected, no telling what she might do. She is one machine that not many people know how to operate and I would like to see her moving dirt !
Matt I really love watching your projects all you do to them. I don't have any experience with operating heavy equipment but I enjoy watching you work on them and getting them running when they have been setting for years. I recently had a partial knee replacement and found you on here and have been hooked. Can't wait for the next video. Keep on rescuing and reviving . Mid Tenn fan
She’s a beast! Did you see your truck squat when you put that massive bucket in the back lol. I’m looking forward to the projects you use her for!
I’m pretty sure I heard a sigh of relief when he lifted it off there also. 😂
Congrats! Awesome find! I hope you get a lot of good use out of it.
Congratulations on your new Excavator! That is Awesome! Now you should look for a M35A2 Deuce and a Half or something similar to add to your collection of cool equipment. It will help pull this excavator around town. Thanks again for sharing with all of us Matt.
Hell yeah! That thing is sweet!!! Looks very good, can’t wait to see it get all cleaned up and maintained. Your channel just rocketed up to most looked forward to watching now!
Thanks 👍
Sometimes good things happen to good people. Been a sub for quite some time. I just sat here with a big grin on my face when I saw what you got. Thanks for the videos.
These are great machines, I'm a dealer tech so I know them well, not sure if it's a ore or post minor change -6 machine. Pre minor machines have fewer buttons on the dash, unless it's been replaced. The other indicator is if there's a grommet on the controller.
Congratulations with the new excavator. Looks great so far ☺️👍 I'm sure you will make it shine again and have much fun and use with it 👍
Very cool Matt. It’s always exciting to get a new toy. I know the feeling well. It never gets old.
Perfect Saturday morning video - I love seeing other people get a good deal and getting excited about putting something back in good shape! Matt, I always enjoy your great attitude and tenacity to get anything needed done - very motivational. Keep the great videos coming. I need to head out to my shop now - lol!
Great find Matt, a good general service will bring it back to its youth.
Just needs a thumb for the bucket and you will be all set.
Enjoyed the show, I'm 58 but you crazy adventures are still inspiring. Just did what I should of done a long time ago and subscribed. Hope you find some rims for Christine.
Wow, awesome deal! I’ve been looking for months now and can’t find any kind of deal remotely that good, you did great! Also, we gotta get a thumb on that thing, looking forward to more vids on this machine!
New to the channel, like your content. Love to see the maintenance process on this machine. Looking for a deal on one myself. Great score!
morning Matt, CONGRATS on ur new to you Kobelco Excavator machine. great find, and you didn't need to take the engine out. lv from sunny florida..
What a deal! For the price that machine is incredible, the cold start sounded great. Those 6 cyl Mitsubishis are super strong, it will definitely pay for itself
I love it love your videos Paint it
Love to see Matt keep making videos fixing this machine up.
That’s a steal for the record book…you’ve got room for lots of repairs & upgrades & you’ll still be in it “right”!
Sometimes it simply right place at the right time & & having the cash does certainly help too.
I’ve been looking at these for a while myself & Im heartened to see there are still good deals out there.
Old Mitsu engines are fantastic. years ago my sister had an older used Hyundai she got and it had a Mitsubishi engine they were using back then, I was delighted. yours is even better.
Mat you are always entertaining & full of surprises with new equipment! 😃
I enjoyed this one, you do a great job with your videos. When I see a new one pop up I watch them right away. Good looking machine, you should get a lot of work of that excavator.
Glad you like them!
Great find 👏🏻 & it was so nice of the local Jr high welding class to put that "hard-surface" welding on the bottom of the narrow bucket. 🤭
You definitely scored a gem in that Kobelco, Matt! Lots of deep TLC and she'll be a long term winner for you. Definite pressure wash everywhere and spit and polish, she'll look great! Looking forward to your maintenance video on her. Spring's a comin' ready for pressure wash season! She's a keeper...👍👍
My favorite way to spend Saturday morning, a cup of coffee and watching Diesel Creek...
Morning!
Great score there man, that's a hell of a machine for that price!! Keep making great content, really enjoy watching your stuff 👍👍
You did good man! Can't wait to see the machine fixed up.
I'm excited for the cleaning / restoration video!
Hi matt,
Your purchase with the Kobelco Excavator seems a super good investment. Everything seems to function entirely properly. I think you as soon as the weather permits you should start with a high pressure cleaning so that you can see the condition of the paint well and the machine will need some major maintenance but that is entrusted to you. On behalf of my wife WIlleke we send you and Debra Lynn lots of love from the Netherlands