1949 PanHead 74ci
Вставка
- Опубліковано 5 лют 2025
- 20120516161027 1
1949 PanHead 74ci #107 Motor Overhaul rebuild FL FLH harley by Tatro Machine
Engine motor overhaul Restoration Rebuild Repair How To High Performance Hop Up Flywheel Balancing Crankshaft assembly Cylinder Boring Honing Case Welding Machining Head Surfacing Porting Rockerarm Geometry Helicoil High lift Camshaft Install Valve Spring Spacing Valve Grinding Cutting Main Bearing Fitting
Thank you for the 7 videos I’ve watched them all 3 times awesome stuff 👍
Man thanks for taking the time to put this together for us. Now in not scared to death to tackle this.
Agreed..... A beautiful engine
Good video. I've never seen a top end of a PanHead in detail before, so it was interesting. Especially those felt 'sanitary napkins' on top of the rockers LOL.
Impressive the way you pay attention to the tiniest of detail. Also, the power kote was a new one on me, wasn't aware of it. Learn something every day
all kinds of fancy coatings and oil out there now.
tatro
By the work you know the man. Good stuff here. Thanks for the videos Tat.
That's a beautiful motor Tatro.
I have a 63 pan bought last fall motor needs bottom redone , this spring I bought a 61 pan motor and Tran work great , watch your videos to set valves and adjust carbuator and to learn how they should run and sound , thanks . 61 starts most days within four kicks , mornings 3 primes ignition and one kick .
Nice Job Tatro well done as always.
Good series of videos, Thanks.
Great video!! Thanks!
It's a Beautiful thing a fresh built motor :)
What valve lash caps are you using? Is that applicable to all panheads? I want to use the same washers under the locks nuts just need to know spec or a source/brand/size? Is it a nut and washer kit?
Question I just had my 50 pan rebuilt and he used hydraulic pushrods because its what he had around, he had ordered the wrong set and went ahead with them. What is your opinion of hydraulic push rods? should i replace them with solids? thanks so much love the videos
they are junk. i would use soilds along with a correct cam.
tatro
@@TatroMachine thanks 🙏🏼 can you use the power kote on the inside of tha case or would you stick with just glyptol?
if i would put anything on the inside of the case it would be an oil dissipate coating. tech line coatings has them.
tatro
did I miss something, no oil drip pipes fitted to lube top of valve? were none fitted on '49 m0tor, valve stem caps fitted instead, do the extra felt mats fitted in valve cover help keep everything drenched in oil up top?.
don't need them. they have good oils now.
tatro
Is it the later model oil set up? 58-64
I think when u put those pans on you had 2 dampners in each one. Then when you switched them u went 3 in one and 1 in the other cause it didnt stick to inside of pan just wondering if u knew
Maybe I'm wrong not sure
i vari the number of pads depending on what i takes to make contact with the cover. it dampens the noise in the pan covers.
tatro
Thanks for response, it's cool u actually talk to us . It's a very nice thing you are doing I bought a 74 iron and so far, learned it all from u ,she runs great. Thanks from Cleveland...
hi Mr Tatro, hope you're well bud. i have a little question about my lifters, i got a 05 sporty, what prep do i do when i re fit the lifters, do i compress them shut or fill them with oil sir? much thanks
your choice. i go dryer with start and stopping the motor until i get oil pressure.
tatro
Thank you Mr Tatro
What mechanic close to spfd mo are st Louis Missouri can assemble a banjo bottom end STD 1985 pan head engine
a torque wrench, REALLY? WTH? LOL
Is it just me or did none of the videos you posted in the last 24 hours load in 1080p Im only getting 480.........Could be just me, maybe need to go to the opticians again.
no, it's just an old video playlist that i reposted. had to learn how to use the camera back then. 40+ videos down to 7. should be easier to watch now.
tatro
Cheers, cancelled opticians.
I can never hear half of what you are saying!