Nice work buddy, but quite dangerous. Why dont you make a push pedal type toe switch, so wen u want to break the wood u tap it with your toe and the device starts to turn. Wen u let go, device will stop. That way more safe.
Felicitaciones bonita maquina,pero muy muy peligrosa,primero deberias bajar la velocidad de giro con un reductor y lo otro colocar un boton mas de emergencia mas al alcance de alguien que pueda socorrerte si la maquina te agarra la mano o el brazo...saludos amigo desde chile.
Although rare, damage can be done to the motor when it is attached to the frame while welding. Stray current can flow through the windings. It’s better to remove the motor when welding.
I have similar project like this but with 3 phase 750w 700Nm electric motor 1360 rpm reduced with drivetrain to 8 rpm on axe. But I will use direct conection without belt.
Топор надо сделать каб рубил на четыре части, а то и на восемь. Как у промышленных дровоколов. мощности хватит если сбавить обороы и повысить усилие на валу
As soon as I find a gear reduction box I am going to make me one of these I’m in to build an outdoor furnaces and log splitters and fireplace. Heat exchanger but I’m going to build this thank you
I've split 5 cords through it so far. Does what I need it to. ua-cam.com/users/postUgkxUyQswtttSffRMblGbrhCvZn7JkhtG1-7 I scrounge all my firewood and am not equipped to handle big wood, but for logs up to 24 inch diameter or so, it works great. I've been amazed by some of the gnarly bur oak and elm crotches it has split. For the tougher stuff within it's size range, you might have to study the piece a bit to decide the best attack, but if you split smart it's up to the job. It did arrive low on oil, and I was would have nicked it half a star for that, but it has regained my full confidence. UPDATE NOVEMBER 2021: Still going strong after all these years. I love the one-handed operation. Hope it's still in production if I ever need to replace it
A bit quick that axe blade don't you think? I would slow it down, presuming the motor has enough torque and the easiest way is to fiddle about with the pulley sizes.
There's no doubting your ingenuity but Three Phase wiring without so much as a gland or proper cable anchors? No chain guard either! Your chain-drive would easily take a hand off!!
На редуктор поставь шкиф побольше, чтоб обороты уменьшить, а сила увеличится.
Зменшити оберти і. буде супер 👍
Nice work buddy, but quite dangerous. Why dont you make a push pedal type toe switch, so wen u want to break the wood u tap it with your toe and the device starts to turn. Wen u let go, device will stop. That way more safe.
Классный дровакол!
Hahaha, this is like medieval torture device for wood 😀
😁😁👍😉
Good work👍👍👍🍻
Thanks bro
esta muy buena la maquina pero va demasiado rápido, great work
Thanks a lot
Felicitaciones bonita maquina,pero muy muy peligrosa,primero deberias bajar la velocidad de giro con un reductor y lo otro colocar un boton mas de emergencia mas al alcance de alguien que pueda socorrerte si la maquina te agarra la mano o el brazo...saludos amigo desde chile.
Video klass, super! 👍👍👍🔥🙏
Zagen zonder beschermkap is levensgevaarlijk.
Good job I wonder if OSHA would approve. I,know I,do
Leave a comment here 👇👇👇
Thanks for your support
Like SHARE and Subscribe
Thank you 😉👍
That machine is all most to dangerous to be safe ! I love it 👍👍👍.
Thumbs up if you’ve still got 2 thumbs!
Nice work 🎉
Thanks 🔥
Fun project
Big like
Thanks
Looks lethal 😂
Real deal chopper well done bro ,
Шпонку болгаркой?!! Виртуозно.
Very Nice Job DK!!!
Классный агрегат супер!!!
Молодец. Лайк
Greath work man !!!
Thanks for Nice comment 👍👍
Although rare, damage can be done to the motor when it is attached to the frame while welding. Stray current can flow through the windings. It’s better to remove the motor when welding.
Автор прошло два года ?!!
Ты ещё живой???🤣🤣🤣
Отзовись!!!
🤣🤣🤣🖐🖐🖐😉👍
That’s awesome 👏 👍 it so much
Thanks a lot my bro 👍👍
I have similar project like this but with 3 phase 750w 700Nm electric motor 1360 rpm reduced with drivetrain to 8 rpm on axe.
But I will use direct conection without belt.
fuerza centrifuga, netamente peligroso para las manos, yo estaba pensando en la broca cónica
А конеческое сверло безопасно?
Super odradjeno!
Hvala Puno brate 👍😉
Iz dakle si ti +??
What mortor use for this machine
Awesome, any ideas where to find a gearbox like that?
You can make wood splitter with motor and reducer. Nice video
Yes thanks
Dobra izvedba ali malo nevarna drugače dobro
I GUESS ALRIGHT IF YOU'RE NOT SERIOUS ABOUT DOING FIRE WOOD TO LAST YOU A WINTER.
Bravo soprattutto per la sicurezza ,quella l hai messa prima di tutto👍
Nicee👏👏👌
Thank you! Cheers!
Super👌👌👍👏👏👏
Super🔧🔧🔧😉😬😁
good idea. it was incredible
Thanks for Nice comment
На уровне изобретения.
этому изобретению сто лет в обед...
🤣🤣🤣
Чёткий агрегат.Тока у меня шота булки сжимаюца .
Топор надо сделать каб рубил на четыре части, а то и на восемь. Как у промышленных дровоколов. мощности хватит если сбавить обороы и повысить усилие на валу
Nice👏👍👌
Thanks 😊
Super 👍
Thank you 👍
You are very skilful, master. It would be an honor for you to work by your side. 👍👍👍👍👍👍
Thanks for Nice comment bro 👍😉
As soon as I find a gear reduction box I am going to make me one of these I’m in to build an outdoor furnaces and log splitters and fireplace. Heat exchanger but I’m going to build this thank you
Thanks a lot
Здорово.
👍
WHATS THE WOOD FOR? TOO SMALL FOR HEATING, LINCOLN LOGS?
I think the speed should be slightly reduced for better safety.
Yes bro thanks
How to motor use HP
I've split 5 cords through it so far. Does what I need it to. ua-cam.com/users/postUgkxUyQswtttSffRMblGbrhCvZn7JkhtG1-7 I scrounge all my firewood and am not equipped to handle big wood, but for logs up to 24 inch diameter or so, it works great. I've been amazed by some of the gnarly bur oak and elm crotches it has split. For the tougher stuff within it's size range, you might have to study the piece a bit to decide the best attack, but if you split smart it's up to the job. It did arrive low on oil, and I was would have nicked it half a star for that, but it has regained my full confidence. UPDATE NOVEMBER 2021: Still going strong after all these years. I love the one-handed operation. Hope it's still in production if I ever need to replace it
What did that old gear reducer come out of?
I don't know bro really i found that 😉👍
By force or 220v
nice welder , still crude where it was put together , is anything square , if taken a little more time , this might have made to last, only my opinion
Nice
Thanks
аппарат классный но пальцев только десять и они не отрастают
My opinion : rotate axe should be slower ...
A bit quick that axe blade don't you think? I would slow it down, presuming the motor has enough torque and the easiest way is to fiddle about with the pulley sizes.
There's no doubting your ingenuity but Three Phase wiring without so much as a gland or proper cable anchors? No chain guard either! Your chain-drive would easily take a hand off!!
Трудно найти большего камикадзе...
Ware are you from
Macedonia
З чого редуктор?
У редуктора корпус алюминевый?
Motor hp?
What is gear ratio of gearbox
Надо площадка, чтобы деревяху не затягивало.
👍👍👍👍
Всё нормално на привари на топор два упора в виде треуголника тогда ещё лутше калоть будет чюрку.
Wow OTT.
Olá, quantos CV esse motor ?
Такие видеоролики надо запретить. Авторам назначить наказание вплоть до изоляции от общества.
عالی
used by the Azov battalions for frank discussions with Russian prisoners,
Za duże obroty a to skolei większe niebezpieczeństwo
put in there a lump I'm wondering how it splits?
I have 6hp motor. When my axe touches the wood, my motor pulley spins, but the gearbox doesnt move. What am ibdoing wrong?
would the motor need to be a 3 phase one or what kind of hp would it need to be? this would be perfect for a wood chunker that I would like to make
Надо лист метала за колуном приворить, что-бы пень упирался
Giró muy rápido, tronco muy pequeño.
Слишком высокие обороты, и так же нужен натяжитель ремня
👍👍👍😎🤗🤗👍😁🇮🇹
Great work! Can you share the HP of the motor and the ratio of the gearbox?
Motor is 2,2kW and gear ratio of gearbox is 20:1. All mentioned in video
@@lojzofilipek5747 would you know about how much a gear box would cost?
Добрый день, на продажу есть у вас такой дровокол?
no bro
@@MrDKDIY 🙌🏻
Больше на щипачку подойдёт
Слишком большая скорость
На редуктор шкив нужен раза в два больше!
👏👏👏👏👏👏
👍👍👍😉
Мужик (пересмотри видео) и сделай правильно !!!
Нельзя варить через подшипник.
👌👌👌👌
Thanks 😉🔧🔩
Такие палочки можно сразу в печь бросать
Продавате ли или не дровокол, и ако да каква е цената
Legna di salice e noce , e con la quercia??
Атракцион " Лишние пальцы"!
👍👍👏👏
😉👍
Why not just use a chopper
🛠👊👊👊
Thanks bro👍👍👍👍
Thise is dangerous all time not same wood.
Oh Oh sehr gefährlich
шкив надо поставить больше на редуктор
Эл.включатель закрыть сзадней стороны.