Products that we use and recommend: ► Voltmeter: amzn.to/4h2sNQ3 ► Panel Removal Set: amzn.to/3YiMADu ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Castrol Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Para las personas que tengas problemas con que les parte se les para en un rato y tira gases por el escape detonaciones no acelera el carro o acelera y solo llega 3 rpm cambien el Sensor de presión de combustible es una chingada ese sensor no da falla en si en algunas oportunidades en el escáner
No the general 3 rule your talking about is fuel spark and Air what is needed to make a gas engine run. Obviously air is pretty self explanatory. Fuel and spark issues can branch out to more sub-issues so to say. Like no spark could be plugs wires or electrical issues. And fuel branches off too.
So when you pulled out the fuse for fuel injector, I just realized that is the fuse that is missing in my friend’s car,that I explained in my first comment. Why the car runs with the injector fuse missing?
My 2008 Mazda 3. starts all the time EXCEPT occassionally it will have to crank for a longer time and stumble to a start. I have noticed that on occassion it happens when I am on a stile incline when it happens. Any ideas what might be causing this? Thanks for your great channel and insight.
My Mazda Tribute, 2003, 4 cylinder, has a problem of cutting off and stop while driving. This happens almost at any speed but almost sure to happen when you slow down. We tried to change the fuel pump, spark plugs, engine oil, oil filter, air filter and some relays but the problem did not go away! What could be the problem? Please help! I live in a remote part of Zambia and have no easy access to good garages and mostly it's guess work we do in order to try and fix the problem! Any suggestions please!
Got an mazda 3 2015 i sport. coils not getting any sparks. I replaced the crankshaft sensor nothing charged. Basically l was driving and the car just turned off on me and not starting up only getting cranks
My problem was no spark no fuel injection no voltage to crank and cam sensors Fuses are ok. i did jumper wire with fuse ignition on to lambda 1 heating circuit where was also Not power it was coming tru ecu so probably ecu broken
Hello, I'm looking to buy Cx7 or Cx9 mazda between 2008-2010 model. I did some research and looks like mazda suv is quite a headache and problematic. Any recommendations? Thanks in advance.
Hmm... I will try a new relay, however with my Mazda 6 I think I need a new throttle body When I force the "butterfly" open the car will start, but run weird because it can not auto adjust when it is stuck in one position...
Yeah, I’d say the motor in the throttle body actuator went bad. Can’t you get just the actuator? Or it’s the pcm not controlling it anymore.. bad circuit
First of all, thanks for the video. Secondly,my friend’s 2011 Mazda CX-7,why are the two light blue relays missing and the two rows of fusible links,next to the relays,on second row,missing a fuse also? But your car has all the fuses,not one missing. Is it not needed ? Thanks
Awesome work. I need some help with my 2011 Mazda (6) Atenza. While driving the car it was shut down with just the ignition lights remaining. I tried to restart the car but it only cranks. After several checks we found out there is no gas feeding into the engine and no sparks from the coil packs either. We changer 3 crank sensors as it was thought to be the problem, but after the 3rd change we decided to looking the issue deeper. We got the car system scanned but nothing was detected except for a code P0661 which was sometging about the manifold sensor. We checked all fuses inside the car and under the hood. All fuses were ok, but we never checked the relays. Can a bad relay make the brain not tell the system to inject the fuel and fire the sparks? There is no sparks from none of the coil packs and the test from the crank sensor connector showed that cables are ok. I even got the computer reprogrammed to see if it was change the status as there is a red flashing 'lock and car' icon in my dash, which someone said the car may have shut down because of this. Any help? No one seem to be able to rectify the problem
@@cedanecox5733 been having the same symptoms on my moms vehicle. i got it going after replacing the crank sensor now its doing the same. this is what i was thinking what the issue is. Wasnt a 100% sure it might be the wiring looks like im going to have to do some continuity test. thanks glad your issue was resolved. safe travels
@@alfredozertuche784 I hope you get this resolved. The insulator was firmly fitted in the connector with the wiring broken so don't be fooled; give it a little pull and if it's broken it will be released easily.
I have 03 Protege 2.0 that cranks but no start I’m unable to communicate with the computer with my scan tool I’ve also tried a different computer and got the same thing hope you can give me an idea of what I can check? Thanks
Hello i have mazda 6 2013 2.2 skyactive turbo diesel I have codes u0100 u0115 u0121 they are permanent the car cranks no start I put new battery checked all fuses and relays Cables and connecters but no use they keyless been checked and its good is there anyway u can help thank u 🙏
My Mazda 5, built in 2001, was driving normally and suddenly it stopped gasping. I had to stop and wanted to restart the car but the only noises came out like in the video. I read the error code P0341 with the OBD reader and it stands for camshaft position sensor. I swapped that out too but still nothing. does anyone have any ideas.
Put it in neutral...it should Start The shifter cable lever at the transmission is probably rusted/not moving properly causing shifter position misalignment
I would like a comment or an idea about what could possibly be wrong when the car (Mazda CX7) starts ie. fires on all four but then immediately cuts out. There was nothing wrong when last used and then this. I have checked the fuses but I don't have a spare relay to swap for one of the others so there it stops.
I replaced my harmonic balancer without finding top dead center first. 😅😅😢 is it possible to get the timing on my motor back correct without having to open up the whole motor?
Jose Torres thanks I figured it out the teeeth on the crank shaft was bent so the sensor was not send getting a correct reading that’s why car was not starting
@@joseone69 Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem? I cleaned the battery terminals and its 12.7v but stil clicks 1st second wil start or 3rd. Somes 1st starts. Any help?
@@jpcyclistangpinoy2989 Yeah, it was a bad battery. I did the chris fix multimeter test and was dropping below 10V when cranking, suggesting that the battery was almost dead. Got a new battery and started it in -25 degrees this morning.
@@jpcyclistangpinoy2989 Sounds like you've got some indepth troubleshooting ahead of you. Spark plugs and starter are what I'd check next, but I'm definitely not a professional...
Products that we use and recommend:
► Voltmeter: amzn.to/4h2sNQ3
► Panel Removal Set: amzn.to/3YiMADu
► Tool Set: amzn.to/3p5MM6t
► Screwdriver Set: amzn.to/3XRB28Q
► Castrol Oil: amzn.to/3xBc8B9
► Oil Filter: amzn.to/3w0Ulme
► Torque Wrench: amzn.to/32qyRwg
► Liqui Moly Engine Flush: amzn.to/3IiDBID
► OBD Scanner that we use most often: amzn.to/3I4MQfe
► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Question i checked everything else changed the relay u replaced and it still won't turn over??
@@rcaddictive8572 maybe it is the crank shaft position sensor
This just saved me a trip to the repair shop. Thanks!
@keith staples did u replace the relay?
What did you do to fix bro ?
Para las personas que tengas problemas con que les parte se les para en un rato y tira gases por el escape detonaciones no acelera el carro o acelera y solo llega 3 rpm cambien el Sensor de presión de combustible es una chingada ese sensor no da falla en si en algunas oportunidades en el escáner
Love your channel but 3 things can cause a no start. No fuel, no spark, and also the 3rd is bad ignition timing.
And how do you fix that
Compression, including valve timing.
No the general 3 rule your talking about is fuel spark and Air what is needed to make a gas engine run. Obviously air is pretty self explanatory. Fuel and spark issues can branch out to more sub-issues so to say. Like no spark could be plugs wires or electrical issues. And fuel branches off too.
So when you pulled out the fuse for fuel injector, I just realized that is the fuse that is missing in my friend’s car,that I explained in my first comment. Why the car runs with the injector fuse missing?
Fyi you can find a fuse tool on the lid of the fuse box . This can be used to pull out the fuses
Gonna have to try this because the people said “its a head gasket u need a new engine” but seems like bs. It cranks but wont start
My 2008 Mazda 3. starts all the time EXCEPT occassionally it will have to crank for a longer time and stumble to a start. I have noticed that on occassion it happens when I am on a stile incline when it happens.
Any ideas what might be causing this? Thanks for your great channel and insight.
My Mazda Tribute, 2003, 4 cylinder, has a problem of cutting off and stop while driving. This happens almost at any speed but almost sure to happen when you slow down. We tried to change the fuel pump, spark plugs, engine oil, oil filter, air filter and some relays but the problem did not go away! What could be the problem? Please help! I live in a remote part of Zambia and have no easy access to good garages and mostly it's guess work we do in order to try and fix the problem! Any suggestions please!
you saved me 700$
thank you!
Mine is a 2011 mazdaspeed 3 and it starts for almost 5 seconds and then die. Any suggestions or advice. Thanks in advance.
Do this also pertain to push start ?
Check the fuse box under hood have somebody hold key on start till u find the right relay to wiggle
My 3 cranks but sometimes won’t start then eventually starts
Intermittent problem
Any thoughts
Thanks for the video, it's helpful
what kina battery does Mazda 2 sports 2014 take ??
Thank you
Really great video ,,,,shearing this video thanks for you ...
Very good Sir
Perfect. can i call your Dr.Mazda? anyway...good job.
it is helping thank you.
Got an mazda 3 2015 i sport. coils not getting any sparks. I replaced the crankshaft sensor nothing charged. Basically l was driving and the car just turned off on me and not starting up only getting cranks
What if it's a smart key ignition
Thank you sooooo much for this video. !!!
Great video. Thank you.
very helpful👍👍👍👍👍Thanks
Excellent video I learnt alot
Thank you, this. Is,, very helpful
My problem was no spark no fuel injection
no voltage to crank and cam sensors
Fuses are ok. i did jumper wire with fuse ignition on to lambda 1 heating circuit where was also Not power it was coming tru ecu so probably ecu broken
Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem?
Thanks for this video
the in tank works but the second one on motor wont even replaced any ideas?
Nice vidéo but I am a bit confused. Why did you replace the fuel injector relay given that fuel pump was working ?
There’s two fuel injectors he said
Hello, I'm looking to buy Cx7 or Cx9 mazda between 2008-2010 model. I did some research and looks like mazda suv is quite a headache and problematic. Any recommendations? Thanks in advance.
Chevy Tahoe.
Hmm... I will try a new relay, however with my Mazda 6 I think I need a new throttle body
When I force the "butterfly" open the car will start, but run weird because it can not auto adjust when it is stuck in one position...
Yeah, I’d say the motor in the throttle body actuator went bad. Can’t you get just the actuator? Or it’s the pcm not controlling it anymore.. bad circuit
Or the gas pedal which sends the signal could be faulty and of course wiring should be looked at just to make sure
First of all, thanks for the video. Secondly,my friend’s 2011 Mazda CX-7,why are the two light blue relays missing and the two rows of fusible links,next to the relays,on second row,missing a fuse also? But your car has all the fuses,not one missing. Is it not needed ? Thanks
Same car here, they are not used in this particular model/year, L4
Please up videos from land rover lr2
I not fine any video for thi vehicle thansk goog job man
I performed DPF regeneration on Mazda C3. After the regeneration completed the car wasn't able to start. Please help..
My mazda starts okay but after driving it don't want to start what could be
My Mazda cx-7 failure to start but when depress gas pedal it start what's the problem
Awesome work.
I need some help with my 2011 Mazda (6) Atenza. While driving the car it was shut down with just the ignition lights remaining. I tried to restart the car but it only cranks. After several checks we found out there is no gas feeding into the engine and no sparks from the coil packs either.
We changer 3 crank sensors as it was thought to be the problem, but after the 3rd change we decided to looking the issue deeper. We got the car system scanned but nothing was detected except for a code P0661 which was sometging about the manifold sensor. We checked all fuses inside the car and under the hood.
All fuses were ok, but we never checked the relays. Can a bad relay make the brain not tell the system to inject the fuel and fire the sparks?
There is no sparks from none of the coil packs and the test from the crank sensor connector showed that cables are ok.
I even got the computer reprogrammed to see if it was change the status as there is a red flashing 'lock and car' icon in my dash, which someone said the car may have shut down because of this.
Any help?
No one seem to be able to rectify the problem
Did you ever fix it
@@therealboss14gaming87 yes! It was the crank sensor. One of the wires was broken in the insulator at the neck of the crank sensor connector.
@@cedanecox5733 been having the same symptoms on my moms vehicle. i got it going after replacing the crank sensor now its doing the same. this is what i was thinking what the issue is. Wasnt a 100% sure it might be the wiring looks like im going to have to do some continuity test. thanks glad your issue was resolved. safe travels
@@alfredozertuche784 I hope you get this resolved.
The insulator was firmly fitted in the connector with the wiring broken so don't be fooled; give it a little pull and if it's broken it will be released easily.
@@cedanecox5733 thanks will be checking tomorrow. i knew it had something to do with the crank sensor but wasnt 100% sure thanks again for the reply
Hei man hw a u I have a problem with my car demio 2005 engine to mush shaking
My mazda 3 2007 coil pack keeps burning what is the problem
I have 03 Protege 2.0 that cranks but no start I’m unable to communicate with the computer with my scan tool I’ve also tried a different computer and got the same thing hope you can give me an idea of what I can check? Thanks
Need a new ecu
Hello i have mazda 6 2013 2.2 skyactive turbo diesel
I have codes u0100 u0115 u0121 they are permanent the car cranks no start
I put new battery checked all fuses and relays
Cables and connecters but no use they keyless been checked and its good is there anyway u can help thank u 🙏
Hello I got the same problem
jose torres so when it happens could be somwthig whith the fuel pump and fuse amd relays
Chrisfix has the answer to your question
My Mazda CX9, 2012, some time the engine does not start on first or 2nd ignition. What should I check?
Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem?
@@dasonest does it lag while trying to start..mine is doing that ..HELP!! No it has juice but won't start
@@rachelr.n.3563 i just used baking soda and hot water to clean the terminal of battery. Since then its starts no issues..
My Mazda 5, built in 2001, was driving normally and suddenly it stopped gasping. I had to stop and wanted to restart the car but the only noises came out like in the video. I read the error code P0341 with the OBD reader and it stands for camshaft position sensor. I swapped that out too but still nothing. does anyone have any ideas.
Jumped timing?
What about 2005 ford territory same problem
Need your help
My mazda 3 2008, will start bu will turn off after a few minuts. After a few minuta it will come bac on,
Any idias???
Camshaft sensor.
What if the P light indicator does not light up and it cranks but does not start. What should we do?
Find a solution??
Put it in neutral...it should Start
The shifter cable lever at the transmission is probably rusted/not moving properly causing shifter position misalignment
I would like a comment or an idea about what could possibly be wrong when the car (Mazda CX7) starts ie. fires on all four but then immediately cuts out. There was nothing wrong when last used and then this. I have checked the fuses but I don't have a spare relay to swap for one of the others so there it stops.
The problem is its a Mazda--make good micro waves when they junked.
I replaced my harmonic balancer without finding top dead center first. 😅😅😢 is it possible to get the timing on my motor back correct without having to open up the whole motor?
Did anyone ever think to check the OBD?
My mazda 3 2008 sedan z6 dnt want to start after l make a short
My starts and then shuts off,I was knocking a nut don’t know if knocking shut down fuel pump
thats the knock sensor shutting down the engine do to knocking , its sounds like you need a engine
Jose Torres thanks I figured it out the teeeth on the crank shaft was bent so the sensor was not send getting a correct reading that’s why car was not starting
@@gawaynepinnock7037 its fuel pump replace compltely
@@joseone69 Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem? I cleaned the battery terminals and its 12.7v but stil clicks 1st second wil start or 3rd. Somes 1st starts. Any help?
My Mazda try to start but wont start like it not getting gas
Does itit work also on 98 323?
Theres no 98 323
@@myes344 depends on your country. we had one.
@@myes344 yes there is is the protege here is link en.wikipedia.org/wiki/Mazda_Familia
How do I reset how do I get to start
Don't think my fuse box ever been opened till today
1991 pickup trck 2200
Drinking game ....every time he says now....or guys
Toyota is the best
Hi. My mazda cx7 is hard starting when cold engine. When in hot weather, it start the engine easily. Anybody experience this problem? How to fix this?
Same issue here. Did you figure it out?
@@Petefenlon did you guys get it fixed?
@@jpcyclistangpinoy2989 Yeah, it was a bad battery. I did the chris fix multimeter test and was dropping below 10V when cranking, suggesting that the battery was almost dead. Got a new battery and started it in -25 degrees this morning.
@@Petefenlon I already change mine with a new battery it worked but again having the same problem after a week..too cold maybe. all fuses are good
@@jpcyclistangpinoy2989 Sounds like you've got some indepth troubleshooting ahead of you. Spark plugs and starter are what I'd check next, but I'm definitely not a professional...
The gage
Let’s just all agree Mazda’s are badly made 🤦♂️
True
Scotty Kilmer loves them.
I loved my CX-9, had no major issues. I traded it in at 140,000 miles, because about half of them will have a massive INTERNAL water pump failure.
Wish I knew that before I bought it
@@kidthunder1311my mom has CX7 and major problem is all windows broken but driver window still fine
Rear door left and right also broken
My Mazda doesn't have those Blue fuises
Mazda duh why won't it start?
Had to stop watching, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS Is all I heard!
Check your hearing aid , maybe a bad connection.
You have a problem bro
Or you could focus on what he had to say
Should we rather subscribe to your channel?
GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS.Watch just to count how many times he says GUYS.Its a joke.
I know what's wrong with this car ....you let a woman near the engine with the hood open 😜😭😂
hilarious
poor video
I'm having er serious problem with your heavy accent, why not just make videos in your native language?
I'm very happy they are making such helpful mazda videos! Regardless of accent :) they make videos other people in the US don't seem to!
The accent is awesome 💪
If anything, the accent makes me feel like his car expertise is more legit 💪
@@johnwatson2379 i'm a mechanic my self and i don't think anything wrong with his accent.
That's rude, I understand him just fine!!
Guys guys guys guys and more guys guys guys because everybody is a man aka guy aka guys guys guys guys guys guys guys......