Appreciate for sharing such useful knowledge ❤️ My case is, when the Water Heater Switch is On, right away the both ELSD & Power Light are Blinking (Green) On & Off without no rhythm/tempo (like unstable power connection or supply). 1) I've already replace the Switch 2) Tighten Wire Connections ( Will try to pull the power supply from wall socket direct into the water heater to check later) As your experience, what would you suspect? Btw, I'll also go thru the test as you mentioned in the video too.
you mentioned that the reed switch is 20mm. Does the max current rating, a switching voltage rating, and/or a max watts rating matter? or as long as it's 20mm, it should be the same? I bought a switch at 19mm and when i turned it on, it burned.
👍Very informative video. Rgdg the eels light, is there something wrong with the WH if the green light is on but pressing the test button doesn’t shut down the system. In other words, the test and reset button don’t work. Other than that the WH works fine. 🙏
Mine is Rubine water heater. look like the reed switch is faulty. need spare part. Do you deal in spare parts. Otherwise where can I purchase the part Klang. thanks
My unit does not have a EELS green light when the mains power is turned on. I suspect the fuse on the electronics board at 4:24.. however I can't properly make out the rating of the fuse - It looks like F1A250V. Do you know if i am reading it correctly?
I'm using joven 510. Frequently the red light will not but sometimes it's fine. Water pressure is okay. Would the problem be the reed? Or the magnetic sensor inside?
I have this joven SB11P. When the power is on, the eel (green) will be on. When I on the heater (temperature), the red light goes on and then off. A while on back and then off again repeatedly. May I know what's is wrong?
Following your video I managed to fix my WH, changing the reed switch also. Thank you so much.
Very informative, clear and to the point. Sir, I'm subscribing right now!
Great sharing. Simple to understand. Tq.
Appreciate for sharing such useful knowledge ❤️ My case is, when the Water Heater Switch is On, right away the both ELSD & Power Light are Blinking (Green) On & Off without no rhythm/tempo (like unstable power connection or supply).
1) I've already replace the Switch
2) Tighten Wire Connections
( Will try to pull the power supply from wall socket direct into the water heater to check later)
As your experience, what would you suspect? Btw, I'll also go thru the test as you mentioned in the video too.
do these reed switches all have the same specification for voltage and current? i have an Ariston brand.
Is this magnetic sensor floating or not? Does circuitry on for a few seconds without the reed switch?
very helpful as I have the same problem where the heater and pump will only start once i've haggled the inlet a bit...
Check out part 2
you mentioned that the reed switch is 20mm. Does the max current rating, a switching voltage rating, and/or a max watts rating matter? or as long as it's 20mm, it should be the same?
I bought a switch at 19mm and when i turned it on, it burned.
I hope i can repair my faulty pensonic water heater..thank you 😁😁
hi, the water keep heating up can’t cut off. what item spoil ?
👍Very informative video. Rgdg the eels light, is there something wrong with the WH if the green light is on but pressing the test button doesn’t shut down the system. In other words, the test and reset button don’t work. Other than that the WH works fine. 🙏
Good
Hi just watch your tutorial very informative by the way where can i buy the reed switch possible from hardware shop..?Thank you cheers
Electronic shops will have. Also watch part 2 of the video
@@jh-ow2zdAwesome! 👍🙂
Mine is Rubine water heater. look like the reed switch is faulty. need spare part. Do you deal in spare parts. Otherwise where can I purchase the part Klang. thanks
No i dont deal in spare parts. Just try shopee!
My unit does not have a EELS green light when the mains power is turned on. I suspect the fuse on the electronics board at 4:24.. however I can't properly make out the rating of the fuse - It looks like F1A250V. Do you know if i am reading it correctly?
Sorry dont know the fuse rating but using simple calculation 3500w /220v = 16. So a 20A fuse should be good
@@jh-ow2zd You are very helpful. Thank you and God bless!
Hello do u still do repair ?
I'm using joven 510. Frequently the red light will not but sometimes it's fine. Water pressure is okay. Would the problem be the reed? Or the magnetic sensor inside?
Intermittent fault is usually magnetic sensor
@@jh-ow2zd thank you
Sir. I just wana ask you, ih have a check valve inside the tube to make one way follow of watter
Its not a check valve. See video no 2.
ua-cam.com/video/4gQ6nq34Ypw/v-deo.html
I see video no.2, so the flow magnetic swicht is like a check valve so that the flow of water can't not reverse
@@wilfredocauzon8741 no. Its a switch to activate the reed switch
I have this joven SB11P. When the power is on, the eel (green) will be on. When I on the heater (temperature), the red light goes on and then off. A while on back and then off again repeatedly. May I know what's is wrong?
How old is it?
About 4 years
@@kenmailim8187 probably magnetic sensor (see video 2) or reed switch. Check if the magnet jiggles freely
What is the problem if the eels/elcb keep on and off?
That is a problem with leaking electric you have to check the components on the board
How about no power/no color green light. My joven unit 510 no fuse
No power is the pcb board itself. Many parts can be faulty and i cant teach in a video
How about rsw over heat after connect together?
That means the reed switch always on
@@jh-ow2zd Ya. after I change the new RSW, when I test run and stop the water magnet boll go down, but the RSW over heat connect together.
Redlight no working wat wrong with it?
Can be alot of different things. Just buy a new one safer if u dont know electronics