I followed just all steps shown in the video and achieved success instantly - Thank you very much. The tape was used probably to imitate the paperbox in place - needed to enable mechanical turn further on. To clean the roll with its dry and slippery surface - I used a rag with purified alcolhol
Had an issue where the printer would print 2 pages and then say it's out of paper even though it's full. Cleaned the roller with IPA and it's now working again. Will keep rocking this printer until it dies :D
great solution. thanks for showing. I cleaned it with lukewarm water, and it worked again. lets see for how long. otherwise, one could change the piece
Guys, if this doesn't work - check the "back door" for "dust" buildup (toner particulate matter/dust). Mine was probably never cleaned and had pretty decent buildup. I dusted (facing rear door) on the right side. This dust must have been sending a false positive of "paper_present = yes"
Any tips on when the pickup doesn't move at all? the printer crearly tries to move something... but then you hear a soft "thud" like something snaping out of socket and the pickup doesn't move and the tray doesn't lift the paper...
Hi. I have this printer, when I turn it on, it makes some noise and spins the motor and then stops, repeats this cycle a couple of times, and then the message “Motor connection error” appears on the computer screen. You can help? Thanks.
when I try to install on my old computer with windows xp home I see smoething like this: you dont have file named: SDcp1215.CHM and stop install orginal driver, why that hapen. Pleasse help.
SDcp1215.CHM Solving my printer problem hp1215:, więc rozwiązaniem problemu było: instalacja sterowników z windows7 32bit(chyba takie same jak do xp wersja basic czyli tylko podstawowe 6.43Mb) i jak ten sam błąd wyskoczy (że brakuje tego pliku SDcp1215.CHM) edycję katalogu w którym brakuje, rozpakowanie dwóch plików spakowanych i w jednym z dwóch folderów jest tam ten plik SDcp1215.CHM. Powiem szczerze że jak na firmę HP to chyba pisali na złość te sterowniki jak by nie mogło wszystko gładko przebiegać. Pozdrawiam wszystkich co poszukują.
You need to put the machine in service mode and the roller will rotate to the correct position to be removed. Another Hack with no idea posting on youtube so others can kill their printers as well.
I followed just all steps shown in the video and achieved success instantly - Thank you very much. The tape was used probably to imitate the paperbox in place - needed to enable mechanical turn further on. To clean the roll with its dry and slippery surface - I used a rag with purified alcolhol
Had an issue where the printer would print 2 pages and then say it's out of paper even though it's full. Cleaned the roller with IPA and it's now working again. Will keep rocking this printer until it dies :D
great solution. thanks for showing. I cleaned it with lukewarm water, and it worked again. lets see for how long. otherwise, one could change the piece
Thank you for the video. What kind of liquid did you use to clean the pick up roller?
I used screen cleaner fluid
Very confusing would be better if you explained what you were doing,
Thank you.
I have used alcohol Isopropilico. And it worked too
My hp laserjet cp1215 power button not working cord is fine but still it's not opening what to do?
Do you advise to remover toner cartridges before tilting on side? thank you for the video
I left toners in and the printed a 60 page document. No problem at all
well I did leave the cartridges on... and ended with A LOT of magenta toner everywhere.... :D
Porque colocou e tirou a fita? Para somente limpar precisa por a fita?? Tem que retirar os cartuchos? Obg pela ajuda
Bhai hp lesarjet color printer cp1215 blank print ka solution Bata dain.thank you
Thank you i will try it
Guys, if this doesn't work - check the "back door" for "dust" buildup (toner particulate matter/dust). Mine was probably never cleaned and had pretty decent buildup. I dusted (facing rear door) on the right side. This dust must have been sending a false positive of "paper_present = yes"
Any tips on when the pickup doesn't move at all? the printer crearly tries to move something... but then you hear a soft "thud" like something snaping out of socket and the pickup doesn't move and the tray doesn't lift the paper...
i have the same problema, catch 1 and after stop catch and continue some operations inside..bought in 2 H and and 1 week and stop working well:((
uso puro algodon seco o le puso alcohol isopropilico?
Ďakujem pekne, pomohlo
Hi. I have this printer, when I turn it on, it makes some noise and spins the motor and then stops, repeats this cycle a couple of times, and then the message “Motor connection error” appears on the computer screen.
You can help?
Thanks.
It worked for me! Thank you very much! Easy and cheap!
why did you put the black tape?
Awesome technical solution
Just dry cotton?
my problem was that it was only printing the first page, It was Chrome configured to print "both faces"
thank you
Thank you!!!
when I try to install on my old computer with windows xp home I see smoething like this: you dont have file named: SDcp1215.CHM and stop install orginal driver, why that hapen. Pleasse help.
SDcp1215.CHM Solving my printer problem hp1215:, więc rozwiązaniem problemu było: instalacja sterowników z windows7 32bit(chyba takie same jak do xp wersja basic czyli tylko podstawowe 6.43Mb) i jak ten sam błąd wyskoczy (że brakuje tego pliku SDcp1215.CHM) edycję katalogu w którym brakuje, rozpakowanie dwóch plików spakowanych i w jednym z dwóch folderów jest tam ten plik SDcp1215.CHM. Powiem szczerze że jak na firmę HP to chyba pisali na złość te sterowniki jak by nie mogło wszystko gładko przebiegać. Pozdrawiam wszystkich co poszukują.
I clean the way showed on videao but still rubber does’nt move
I follow all steps in video but roller not moving
ua-cam.com/video/jf0x1aZ9kSM/v-deo.html
Would have helped if the guy would have talked.
In toàn màu đen là bị gì?
THX
تعمیر برای مدت کوتاه هست
You need to put the machine in service mode and the roller will rotate to the correct position to be removed. Another Hack with no idea posting on youtube so others can kill their printers as well.