Why every time you make video content doesn't tell you the types of components you use, such as diodes (in other videos), transistors or mosfet even capacitors. And my advice is better, you answer questions from your subscribers or I'll just unscribe later. Please answer
Again I want to commend you for doing good, but you are not carrying your students along, so how do you expect us to pass? Can you please tell us the exact name and specification of each components. Thanks
Five thousand watts my arse. The transformer is rated at no more than 1kw and those transistors aren't beefy enough. Oh and 5000w from a 12v source needs over 400 amps, so why is it all wired with thin wire?
Vc deveria detalhar de onde vem as alimentações, e o centro tape. Muito bom agora falta detalhar para que as outras pessoas possam montar. O you tube é para isso para compartilhar conhecimentos, fica muito a deseja vc expor um vídeo só para mostrar para as pessoas que funciona os seus conhecimentos sem compartilhar.
I was waiting for the still 😢😢😢, great video, please do 🙏 another version with microwave transformer and power drill n other heavy stuff like iron n kettle....❤❤❤❤❤
I really appreciate your efforts, but do you know that all your mosfet transistors were tite on the same heat sink and your transformer cable was connected on the same rael please take note
Hello, can two capacitors be inserted in the circuit? the first to raise the input voltage before the circuit, and the second capacitor after the circuit to enter a higher voltage in the coil?
Viewers have you notice? The two red wires from the microwave oven he hooked up to the drain. The drain and the heatsink is what? Just do it in actual it will not wotk because there is a trick. He did not shows us properly what he did. The key is in the two red wires and heat sink drain of the mosfet portion just observe by using multi tester.
It can not be 5 kW at 50 or 60 Hz. Core size will not support the required flux. If not too much core loss at 400 Hz, 5 kW may be possible at the higher frequency.
1- Not possible. The way you have connected all four drain pins of the mosfet directly to the heat sink is definitely a shot circuit. I didn't see any insulation between mosfet and heat sink.The transformer winding are therefore shorted. 2- The secondary of a microwave oven transformer is a high voltage, around 5kv, enough to burn those mosfet (IRF3205) instantly because they can only sustain a 55 to 60 volt maximum, 3- You show on the meter A DC Reading, if those mosfet were oscillating to high voltage ac you'll no longer have a meter. it will be toasted. 4- As others pointed out, An honest inventor will not hide anything, like those wire that no one knows were they attached to. 5- Please get real tools for a credible projects. Do not use a rusted scissor to cut wire get a real wire cutter.
I respect your comment, however what do you propose has been done? Entire circuit running on AC?! It was only due to camera angles that the source of the red and green wasn't shown, was clearly DC however while end result is clearly AC. Regardless of your suggestion that it "doesn't work" it clearly does, as others have demonstrated through similar videos. Furthermore, while the instruments/tools used may be rather rudimentary, they still are functional and arguably all the more attractive. There's something far more amazing in watching an individual make something out of virtually nothing, than one who does so with a great deal of advanced tools! Pakistan has many fine examples of Anvil + hammer + tongs truck or vehicle repairs. This video highlights the beauty of a creative human mind, at work with the humblest of tools, making the most of what they've been dished out in life. Greatest respect for these videos and individuals.
The DC source/battery presumably?! ;-) Lightbulbs AC, can't imagine the circuit would be able to be "faked" and running on AC input as some have suggested.
Desculpem amigos. O multimetro estava na escala DC lógico 12 volts DC. A bobina q foi usada foi a menor jamais seria d alta tensão. Eu vi assim. Não tem como da curto se o outro lado não tem corrente nenhuma.
Nunca muestra en el video a donde lo conecta, a una batería seguro que no, así como está armado no funciona con una Batería, terminas quemando los mosfet
Why every time you make video content doesn't tell you the types of components you use, such as diodes (in other videos), transistors or mosfet even capacitors. And my advice is better, you answer questions from your subscribers or I'll just unscribe later. Please answer
So true
Eso es cierto, nunca dice los componentes que usa
Eso es cierto, nunca dice los componentes que usa
Again I want to commend you for doing good, but you are not carrying your students along, so how do you expect us to pass?
Can you please tell us the exact name and specification of each components.
Thanks
Five thousand watts my arse. The transformer is rated at no more than 1kw and those transistors aren't beefy enough. Oh and 5000w from a 12v source needs over 400 amps, so why is it all wired with thin wire?
@Gamerpro So what are you testing - how long it takes to catch fire?
Vc deveria detalhar de onde vem as alimentações, e o centro tape. Muito bom agora falta detalhar para que as outras pessoas possam montar. O you tube é para isso para compartilhar conhecimentos, fica muito a deseja vc expor um vídeo só para mostrar para as pessoas que funciona os seus conhecimentos sem compartilhar.
I was waiting for the still 😢😢😢, great video, please do 🙏 another version with microwave transformer and power drill n other heavy stuff like iron n kettle....❤❤❤❤❤
I really appreciate your efforts, but do you know that all your mosfet transistors were tite on the same heat sink and your transformer cable was connected on the same rael please take note
Donde esta la bateria ?de cuantos amperios,cuantos voltios?
If i have 37v battery then what should i change on this circuit to make it work?
I contacted diode rectifier to make battry charger from it but rectifier heatup alot why ?
Why is the input source of current always hidden in this video
Yeah 5000kw is like 416 amps at 12 volts so nope it’s not really fake it works for tungsten lamps only this can kill charging devices thou
How many volts is the transformer?
❤❤❤❤😅😊😊😊🎉🎉🎉 Please 🙏🥺 make another version with microwave transformer 10KW...🎉🎉😊😊😊
Diagram?? Or type transistor? Resistor?
Hello, can two capacitors be inserted in the circuit? the first to raise the input voltage before the circuit, and the second capacitor after the circuit to enter a higher voltage in the coil?
Creative video, thanks :)
That's right, well done
Great. Can it work with 12v battery? Can DAT same connection go to electricity?
सुपर हिट राणा दुदाभाई..खानपुर थराद
Sugestão de vc colocar escrito na tela a descrição das pecas usadas e ligação a cada procedimento feito
3 Tecnology great invention Amazing
We never saw where the green and red wires got the juice. Could you tell us? Thanks.
Hallo! what is the resistor in the middle
вау, это чё , то о чём я тебя просил почти. без моторчика . круууть. давай ещё.!!!
What is tha resistance no?
Which Type of Transistor is used ( PNP or NPN)?
irf 3205 mos
One light bulb 5000W, amazing!
I respect your thoughts. I would appreciate it if you could also let me know the part name, specification, and circuit diagram.
Kul
Kul
I doubt it can generate 4500W
What are those black wi 3 terminals? Mostfets transistors pnp npn ets?
Vi a maior parte dos comentários que é fake. Vc é capaz de provar o contrário? O mundo inteiro espera a sua resposta.
My transformer is 110v . Is the same Circuit?. Tanks in advance.
Como se que lo tu haces funciona si nunca dices que tipo de componentes usas
Ya estoy buscando un transformador de microondas. BRAVO 👌
Спасибо за материал!!! Надо бы транзисторы на теплопроводную пасу посадить КПТ-8.
That's only 50 watt.not 5000 watts.
Please put the circut diagram
Sans enlever la hot tension c'est du fake
Здравствуйте! Собирал точно как было на видео, только нету выхода 220в.
Brother the watt of resistor is 1 watt or 1/2watt? Thanks 👍 good job!
Please, where the green and red wires come from? another outlet power? I do not get it, please, explain the purpose.
Can you send me the details of parts and value of each part ang also the diagram 🙏
What is the power batarry Or Ac
Viewers have you notice? The two red wires from the microwave oven he hooked up to the drain. The drain and the heatsink is what? Just do it in actual it will not wotk because there is a trick. He did not shows us properly what he did. The key is in the two red wires and heat sink drain of the mosfet portion just observe by using multi tester.
I literally performed all the circuit applied to the 12 volt mosfet (IRF3205) the current in the pins does not circulate and the mosfets remain cold
You done this project and dont work it. Answer me
@@miodragmitic1931 hello if you want I'll send you a photo of how I assembled the components. but i can't get it to work.
And where did the green and red wires go?
12 VOLT DC
to the death
Wow am so impress
de cuanto es la resistencia?
Promise many Watts (9000w) bit Is real?
Resistor ohn? W?
Video chichi pato no muestra de donde salen los cables que llegan a los transistores solo mide pero ni sabe que es lo que mide 😂
Hi, I just tried it - and it is not working. I just blew up my multi meter and all mosfets.
Please what is the value of the resistor???
330 Ohm
with a troughput of 5Kw, u dont need a light bulb.. those MosFet´s will give the light ... lol... 🙂
It can not be 5 kW at 50 or 60 Hz. Core size will not support the required flux. If not too much core loss at 400 Hz, 5 kW may be possible at the higher frequency.
Quantos volts na entrada?
1- Not possible. The way you have connected all four drain pins of the mosfet directly to the heat sink is definitely a shot circuit. I didn't see any insulation between mosfet and heat sink.The transformer winding are therefore shorted.
2- The secondary of a microwave oven transformer is a high voltage, around 5kv, enough to burn those mosfet (IRF3205) instantly because they can only sustain a 55 to 60 volt maximum,
3- You show on the meter A DC Reading, if those mosfet were oscillating to high voltage ac you'll no longer have a meter. it will be toasted.
4- As others pointed out, An honest inventor will not hide anything, like those wire that no one knows were they attached to.
5- Please get real tools for a credible projects. Do not use a rusted scissor to cut wire get a real wire cutter.
I respect your comment, however what do you propose has been done? Entire circuit running on AC?! It was only due to camera angles that the source of the red and green wasn't shown, was clearly DC however while end result is clearly AC. Regardless of your suggestion that it "doesn't work" it clearly does, as others have demonstrated through similar videos.
Furthermore, while the instruments/tools used may be rather rudimentary, they still are functional and arguably all the more attractive. There's something far more amazing in watching an individual make something out of virtually nothing, than one who does so with a great deal of advanced tools! Pakistan has many fine examples of Anvil + hammer + tongs truck or vehicle repairs. This video highlights the beauty of a creative human mind, at work with the humblest of tools, making the most of what they've been dished out in life.
Greatest respect for these videos and individuals.
نعم هذا الرجل يعمل على تضليل الناس فهذا العمل غير صحيح ومضلل
Awesome 👍👍👍👍
Kudos to you but the red and green wire connected to the MOSFET where are they coming from?
The DC source/battery presumably?! ;-) Lightbulbs AC, can't imagine the circuit would be able to be "faked" and running on AC input as some have suggested.
Desculpem amigos. O multimetro estava na escala DC lógico 12 volts DC. A bobina q foi usada foi a menor jamais seria d alta tensão. Eu vi assim. Não tem como da curto se o outro lado não tem corrente nenhuma.
how much ohm resistor use my friend???
330 Ωμ
Show 5000 watts load against this transformer. It cannot hold that much power more than 500 watts.
Direnç değeri nedir
حضرتك افين رقم الاترانزيستور ولا اسمه ايه الشرح مش واضح ولا المحول بيظلع كام
Can you tell me this project true?
Hola, una pregunta y los 12 voltios se sacan de una bateria o de donde.
corriente continua
C.A
cual
Se vc erra em alguma coisa vc é um cara morto ,retira o secundário rapaz.se tocar no secundário sem querer morreu .
Boujours Mr quel résidence utiliser?
Есть только сомнения. Сопротивление 330 ом или же 33 ома. Ещё возможно должно быть прокладки для второго пар транзисторов.
А нарисовать схему можно?
No any name or the value of transistors and the resistance value,inlet volt ac or dc..the outlet watts.
Ok felicitari
Caution! Permanently magnetic-current > 3A ... it lasts Batterie!
Hi .. congratulations, you are always very precise and clear ... I have a question ... how many AC volts and amps go into the transformer? thank you
@
@@mdrajiuddin4213 please what's the input voltage, transistors name and the value of the resistor. Warm regards Sir
230 volts
TENGO UNA PREGUNTA? SI NECESITO 110 VOLTIOS ¿QUE CAMBIOS DEBERIA DE HACER? POR FAVOR
I am going to assume you used resistors to lower it to 110
❤
qual tensao de entrada............
Damn France internet
5000 WATTS ??????????????
NOT EVEN CLOSE !
Lack of knowledge on your part.
Equals POSSIBLE dead/injured people !
⚡
ใช้ D 718 แทนได้มัย
Why are you hiding the green and the red cable
Por onde entrou á alimentação
so... what magic did you use to transform a simple MOT for 230v at "5000w"? I think we've got some fishy video around here
You could be right because when we ask him for names of the parts, he just will not answer ,maybe fake.
Pakistan, Good
Fake informations
The music is killing meeeeeeeeeeeeeeeeee.
I doubt it can generate 4500W
Hola boa noite muito top o amigo pode me dizer quantas horas é a durabilidade da bateria nesse inversôr?
Amigo isso aí não funciona não 🤣
Схему можно скинуть
Apa nama komponen2 tersebut?
Rahasiaa, mau tahu aja ato mau tahu bangetT 😂
Kd a alimentação ???????? kkkkk
do jeito que ele fez ai ta queimando o mosfete porque tem que isola o mosfet do dissipador
Montei e não funciona é treta a alimentação desses dois braços são apenas de 3volts e não usa centro tape.
Nunca muestra en el video a donde lo conecta, a una batería seguro que no, así como está armado no funciona con una Batería, terminas quemando los mosfet
12 volt aku kgorunmuyor
Que tipo de corriente les ponen batería ho cientodies
ele so faz mais nao da explicaçao base dos mosfete fica em curto
pecimo video , ALEM DE SER FACK
Value of coposent
Example resistance nu trans
Please don't do this ! The lack of detail makes it dangerous . ( 2000 volts ! )
Los tipos de componentes que usaste por favor enviame los datos
Подскажите пожалуйста у каво получилос спасибо заранее г.Ташкен
LOL
Well done,I love it.I just got to know where is the green and orange cables gone down,cant see it....many thanks in advance
Plzz sir don't share fake knowledge
😆😆😆