I'm so glad you made this video. I always wanted to know this process. Sure wish I could hear the voice a little better, but I really appreciate you taking the time.
Thanks for a great video. I will be moving my lift in two weeks and this help me lot. But I am planing to plug the vent holes on the bottom just to be safe, this should eliminate use of the generator. Hopefully will work !! LOL
@@humanofearth7524 Goes pretty good, I used the 4" expendable plugs you can buy in Home Depot , plumbers used them to pressure test the pipes. Each tank have a two 4 " holes. Lift is already installed in new location and work a great.
Letsgostblues glad you appreciate the video! Just a heads up, if you don’t have a generator that will run the blower, be sure to get the plugs for the vent holes on the bottom of the tanks. When I said “it sinks fast”, It does, luckily we hadn’t unbolted the front two bolts yet😎. Not gonna say why😬. The process takes some time but is simple. Just keep the back end down in the water! Plug the vent holes or take a generator and you’ll be golden. We moved our lift just under 2miles with the generator method and no plugs. All the best!
Put some water in the tubes so the unit doesn't want to flip over (neutral bouyancy) then seal the holes ( stadium cups notched for and held with straps for the water side) so the air/water mix can't change. You will have to drain the water if you are trailing at the end. A shop vac is a good portable level changer.
I do this for a living and ill tell you there are much much easier ways to do everything here but you have a lot of the right ideas at least you didnt sink it haha
Don’t you just love the Sofa Quarterback’s always criticizing, yet having nothing to offer other than diarrhea mouth. Hey pal if you can’t help others just shut the fuk up!
With a Tri-toon boat lift, do you think a lift could be moved from 1 slip to another by strappiing lift tanks to the tri-toon tubes and sinking just enough to enable boat motor operation?
Possibly, I would definitely use the plugs on the vent holes. I Would hate to see you sink the boat. If you’re not leaving the marina, you and a friend could probably just paddle down to the new slip.
What size slip did you remove this from in your video? 10ft wide?? I have a UL2 6600 and I need to swap the pitman arms around so they are out of the water when the lift is raised. We have a 10ft wide slip and a Cobalt 262 boat.
Looking at moving a hydrohoist 6600 in the next couple of weeks. Where exactly are the vent holes and what size trailer did you use? I have a 6' x 12' and plan to just slide the tubes in to fit once we get to the takeout point. I have access to a pontoon trailer but think it would be hard to keep secure on the bunks.
The vent holes are on the bottom of the tubes, near the back of the lift. It is very heavy. I used an 18 foot car hauler. A pontoon trailer would probably be better than a 6x12. I don’t think a 6 x 12 is wide enough or could handle the weight.
❤❤Going to remove a used lift and found this video just in time. Thanks for helping decide what to bring to the Marina.
I'm so glad you made this video. I always wanted to know this process. Sure wish I could hear the voice a little better, but I really appreciate you taking the time.
Great! Thanks for the video. I just bought one and I'm the process of doing logistics in how to move it.
Let us know how it turns out and any other tips you discover.
Thanks for a great video. I will be moving my lift in two weeks and this help me lot. But I am planing to plug the vent holes on the bottom just to be safe, this should eliminate use of the generator. Hopefully will work !! LOL
How’d it go?
@@humanofearth7524 Goes pretty good, I used the 4" expendable plugs you can buy in Home Depot , plumbers used them to pressure test the pipes. Each tank have a two 4 " holes. Lift is already installed in new location and work a great.
Thanks for sharing this content. I’m going to tackle one tomorrow. Your efforts on making this video are appreciated!!
letsgostlblues good luck tomorrow. Let us know how it goes. I need to post a follow up with this lift in its new home in TN.
Letsgostblues glad you appreciate the video! Just a heads up, if you don’t have a generator that will run the blower, be sure to get the plugs for the vent holes on the bottom of the tanks. When I said “it sinks fast”, It does, luckily we hadn’t unbolted the front two bolts yet😎. Not gonna say why😬. The process takes some time but is simple. Just keep the back end down in the water! Plug the vent holes or take a generator and you’ll be golden. We moved our lift just under 2miles with the generator method and no plugs. All the best!
The gen is a great idea!!
Thanks for the making this much appreciated
You’re welcome. Hope it helps you with yours.
Put some water in the tubes so the unit doesn't want to flip over (neutral bouyancy) then seal the holes ( stadium cups notched for and held with straps for the water side) so the air/water mix can't change. You will have to drain the water if you are trailing at the end. A shop vac is a good portable level changer.
Great video
Good video there is also some plugs you can buy for 20$ each
Yes, the plugs are ideal. It was 2020 and we couldn’t get them in time.
@@joshdickerson8962 how many plugs are there for each float?
I do this for a living and ill tell you there are much much easier ways to do everything here but you have a lot of the right ideas at least you didnt sink it haha
Definitely not our daily job. There was a lot of trial and errors as we went.
Post a video on a different better way to do it, please.
Don’t you just love the Sofa Quarterback’s always criticizing, yet having nothing to offer other than diarrhea mouth. Hey pal if you can’t help others just shut the fuk up!
With a Tri-toon boat lift, do you think a lift could be moved from 1 slip to another by strappiing lift tanks to the tri-toon tubes and sinking just enough to enable boat motor operation?
Possibly, I would definitely use the plugs on the vent holes. I Would hate to see you sink the boat. If you’re not leaving the marina, you and a friend could probably just paddle down to the new slip.
I need to convert my lift to a tritoon any direction on how to invert the arms?
Does any one know what this hydrohoist weighs? or what each tank would weigh?
What size slip did you remove this from in your video? 10ft wide??
I have a UL2 6600 and I need to swap the pitman arms around so they are out of the water when the lift is raised. We have a 10ft wide slip and a Cobalt 262 boat.
I’m not sure but I think it was either 10 or 12 I had to widen it out for my slip and mine is 14.
take the two side rails off. flip the front arms up. rule of thumb is 7ft 11'' if its a 10ft slip
Looking at moving a hydrohoist 6600 in the next couple of weeks. Where exactly are the vent holes and what size trailer did you use? I have a 6' x 12' and plan to just slide the tubes in to fit once we get to the takeout point. I have access to a pontoon trailer but think it would be hard to keep secure on the bunks.
The vent holes are on the bottom of the tubes, near the back of the lift. It is very heavy. I used an 18 foot car hauler. A pontoon trailer would probably be better than a 6x12. I don’t think a 6 x 12 is wide enough or could handle the weight.