I love your success smile at the end of your repair videos....real genuine pride in your aspiration to do good work at what you truly love all Americans should aspire in this way this is how freedom should make people truly be and live free with the gift of freedom our country was founded for...awesome my friend
Did you consider putting the wire on after attaching the flex instead, to allow the flex to sit flat on the board, I’ve never done it so I don’t know how hard it is to do, just wondering if that would be easier.
When work is done he laughs and sound changes thats how he is dedicated to work love from kerala india daily watches ur video .and most satisfied video in repair is urs due to ur presentation and cameras
Amazing soldering work. Couldn't figure out why, even with Amtech, my solder was creeping up the iron tip. Now I'm thinking maybe I need to increase my temp from 385C. 🤔
What a shame, he actually did a good job with the jumper cable but in the wrong place, he was pulling a data line to ground, even though he botched it, it was a good try, but as always you saved it with your master skills, great video!!!
MashaAllah. It was really better than factory. Sir you should work in NASA or similar to NASA. You know almost all in and outs of electronics. I wish you all the best ahead 😊😊😊😊👏👏👍👈 GR8 JOB SIR
master i am very glad to see your videos you are the best in youtube , i came from Iran and have the same job , master if its possible for you can you fix a graphic card with short problem not gpu chip problem too?? you are the must perfect teacher in youtube and the job i ever seen i learn a lot from you and used in my case too Thank you master BIg love
i would have done it slightly different ,(only after watching your videos it made me think about it) instead of the enameled wire going under the flex connector and on top of the solder mask (which could have made it more pronounced )that the flex cable might not have sat nicely ,you could of masked the board then added the flex cable then the jumper wire on top of the flex where you have even more space to tack it down.
You could have soldered their flex cable without putting that wire pad, and then connect pin 4 to the test point as you did. It would be a bit less work imho Great job
probably seen 20-25 of your videos in 2days 🤣🤣will see more until i finish them all😁
You can jumper wire after adding the flex cable.over on flex cable.
That's what I was thinking
Yes, but this way the jumper wire is out of the way and wont get broken loose if someone opens the ipad later?
Nice repair but it is much easier to do this after the port is on, just cover the wire in uv solder mask so it doesn’t get knocked on future repairs.
I love your success smile at the end of your repair videos....real genuine pride in your aspiration to do good work at what you truly love all Americans should aspire in this way this is how freedom should make people truly be and live free with the gift of freedom our country was founded for...awesome my friend
Today, I had the privilege to like two videos in 1 day.
I'm literally learning a ton of things for your videos dude! I wanna be good in the field of microsoldering so yeah watching your videos are worth it!
Did you consider putting the wire on after attaching the flex instead, to allow the flex to sit flat on the board, I’ve never done it so I don’t know how hard it is to do, just wondering if that would be easier.
I see your videos recently and I can tell that you are an amazing person and you do your art with love
That was a good strong repair! That's how a professional does it! Thanks.
After the job, smile on your face is amazing
Can you please make a video on all the tools you use at work..describing tools and how to use it...
When work is done he laughs and sound changes thats how he is dedicated to work love from kerala india daily watches ur video .and most satisfied video in repair is urs due to ur presentation and cameras
I like your smile when you fix a unit.
Just bought some flux from you and looking forward to trying it. Thank you for a great channel
I am not a hardware guy, but still loves to watch your videos 😂
Wuhhuuu a new video. Btw you never sleep🤣🤣? I am from germany and the video came up at 10:35 my time.
Nothing like that smile of victory at the end...!
You are the best profesional technician i ever seen.
Regards.
Thanks a lot,sir
You made it look more easier than expected,and i got high hopes am gonna make it work tomorrow ..
Once again thanks a lot
You make my day really
And want to know where i can find diagram for iPad air first generation
Wonderful work and great effort thanks
Amazing soldering work. Couldn't figure out why, even with Amtech, my solder was creeping up the iron tip. Now I'm thinking maybe I need to increase my temp from 385C. 🤔
Thanks!
Очень круто, когда хочу увидеть прекрасное, смотрю твои ролики! best job bro 👍(hi from russia)
What a shame, he actually did a good job with the jumper cable but in the wrong place, he was pulling a data line to ground, even though he botched it, it was a good try, but as always you saved it with your master skills, great video!!!
Beautiful pads.!!!! Better than factory.
Good job👍 as always
Cant get enough of your videos.
Good repair! Very good technique :)
10/10 for the hot tweezers solder whick trick tho. My new number one for pad cleaning.
Good work and thanks for all.
There’s the amazing knife again!
Maybe the previous repair connected to the wrong test point (the one with a drop of solder without any reason...). Beautiful repair as always
Great many thanks for sharing your knowledge with us, great work
Your fan from india 🇮🇳😍😍😍
Your fan from india 🇮🇳😍😍😍
Nice work
I Like your smile after the successful efforts keep it up 🏅🏅🏅
where you get the circuit diagrams of every devices you fix.????
MashaAllah. It was really better than factory. Sir you should work in NASA or similar to NASA. You know almost all in and outs of electronics. I wish you all the best ahead 😊😊😊😊👏👏👍👈 GR8 JOB SIR
Very nice and a professional job done.
as a student i've many many learn from him.
Nice work..please let me know where u getting the diagrams for mobiles please
sir good day.. Can you show me the tools you've been using like the tool you use to check if it's charging. Thank you sir
Flux is the best friend
معلم حسن كيفك . فيك تشرحلنا عن بصمة الوجه ب اجهزة الايفون الحديثة ؟؟؟
master i am very glad to see your videos you are the best in youtube , i came from Iran and have the same job , master if its possible for you can you fix a graphic card with short problem not gpu chip problem too?? you are the must perfect teacher in youtube and the job i ever seen i learn a lot from you and used in my case too Thank you master BIg love
Very pretty repair 👍
U r the King of iPad
i would have done it slightly different ,(only after watching your videos it made me think about it) instead of the enameled wire going under the flex connector and on top of the solder mask (which could have made it more pronounced )that the flex cable might not have sat nicely ,you could of masked the board then added the flex cable then the jumper wire on top of the flex where you have even more space to tack it down.
amazing work i confirm , better of factory ;)
Nice job sir.very cleaning same like factory like you said 👍
superb skill.... great to watch a master,,,....
Nice video sir. My iPad mini 1 has trace damage hope u can upload ipad mini 1
You could have soldered their flex cable without putting that wire pad, and then connect pin 4 to the test point as you did. It would be a bit less work imho
Great job
You can definitely do that, no right or wrong way, but having the wire under is cleaner and you don't see it.
@@NorthridgeFix That little bit of extra effort brings the customers back again and again. Another fantastic repair!
lol, did one of these yesterday my first one was fail, so annoying when you have to do the walk of shame back to ur desk
The jumper wire looks like a fishing hook 🤓😂😅 good job bro 🇩🇿🇩🇿
Good work teacher 😁
Thanks for sharing your knowledge
my first run in with what was in the soldering world. I destroyed some pads, boy did I!
Well, what's the name of green foam?
Uv-mask
MECHANIC 10ML GREEN UV SOLDER MASK
very nice.job..stay safe
That weld is very nice !
👌
I like your system to work.
@NorthridgeFix what is the temperature that you would use if there was no preior fix attemp?
What temperature are you using for desoldering SMD parts, and what kind of flux you use. Thanks in advance
Amazing fascinating to see such skill
Whats the software you use to find where connect each pad?
i have a ipad with 15 pads missing, can help me?
What is the liquid kind of thing you add while soldering, is it some kind of flux?
U really hardwork sir
which liquid you r using for cleaning bord
Why sometimes you work with prior fix attempt and sometimes no ? What makes you decide ?
can you send me an ipad Air 2 board diagram? I am in a lost here since I mess up the pads of the mother board. Thank you very much.
which software u r using for tracing tracks plz tell us
Nice job Sir 👍👌
What's the name of the software you used to see jumper. Good work by the way your channel is helping me a lot on my repairs 🙏
Did you learn how to do these kinds of things by yourself or at school/classes?
Nice video and job
I am your student sir
Your my teacher
Do you have place that I can buy the ipad min 2 internal memory drive?
What is that liquid green material name?
Hey ı am new at this. What is that gel
Müthiş işçilik Turkey selam. Allah işini gücünü rast getirsin.
amazing work
hi wht is the name of the green glue?
It’s a kind of magic!
S better than factory👌👌👌
Amazing skills
Can i replace ipad with changed dezitizer under warranty in apple authorised service center (my ipad is not restore or update error 4013)
Always good job
Awesome 👍🏻👍🏻
How to find board diagrame plz help me
It's now hard like a rock - that's what she said
I want to make a clip for iPad mini 4.
Please share the software name and link.
What’s the name of pcb maps software?
So what do you called this blue thing that hardens with UV light?
Green uv-mask
MECHANIC 10ML GREEN UV SOLDER MASK
@@skeptisk1 thanks bro
Samsung a51 water dameg from Pakistan plz help
Brilliant bro
well done
good job
Phoneboard which is it
NICE VIDEO
Flux ??
It seems his mistake seems to not being able to see the pin was connected somewhere else 😕