Thanks for a great tutorial! Do you know if the approach is similar with the iPad 2018? I have just switched out the glass+digitizer after a cracked screen but now after reassembling it I get a dead spot in the same area as in you video? Can it be remedied in any other way, like pressing on the area connecting the pins or something...? Please help?
@@charukadewasurendra3347 Yea, it was that the connector for the digitizer wasn't connected properly. So I disconnected and connected again, more thoroughly, and then it worked
I had same issue. I cleaned the connectors on my 2018 ipad6 with 99% alchohol. And tada, the whole screen worked again:). It is the connectors that are not clean or in place.
@@TheVolcomDust I realize your comment is like 2 years old but I have to thank you for posting it. Having just replaced my iPad battery and screen I lost half of the touch functionality, your comment lead me to check the cable connection and the dam thing was a little loose. Thanks because I would have assumed the screen I bought was junk otherwise..
I had dead spots at pretty much the exact same location on an iPad 2018 after a glass/digitizer replacement. Thought either that the new wan was faulty or that the connectors were fried. I also tried with a multimeter and found that two edge pins on the large connector didn't show any resistance, and thought for sure that the iPad was faulty. So I wiggled the pins SLIGHTLY and put the cables back and thought I could take it to an authorized repairer. But then, 3d or 4th time putting it back together it all worked! Maybe it was the wiggle, or maybe I got the cables on more correctly than previous, either way very happy about it.
hi sir, i've recently changed my ipad's touchscreen (same model of ipad) and i have exactly the same dead spots. my best bet is, the repairer didnt do a good job while installing the screen, maybe the same case as yours. could you please tell me what you did to fix the problem? i would appreciate it very much! you can contact me @bryansoon2001@gmail.com, thank you sir !
@@fomor1974 The connectors for the digitizer are really tricky to get right. Think there are about 86 pins between the two that has to line up correctly. Disconnecting and connecting the digitizer cables is fairly easy, but you have to remove the LCD connection to reach them, and before disconnecting the LCD you should disconnect the battery, which I found quite hard the first time, feels like you're about to break it cause you really need to jam a pick (or similar) in there to disconnect the pools. Not to mention before doing any of this you have to disassemble the iPad, removing the glass using suction cup, heat gun and plastic tools to pry it open. My glass was already broken when doing this and by the end it was in pieces. Guess you could take it back to the repairer and argue that the digitizer isn't connected properly and you want to be refunded.
Hey, hows the ipad holding up. have the same issue with mine, fell and screen broke, after replacement, got two dead spots, sent it back to the repair center and nothing, though the new screen works on other ipads so i'm guessing my connections are messed up too.
Hi @Rewatechnology My Ipad Air 3 Touch works preety well at Times and At times part of the touch get stuck/Froze for a few seconds What do u think could be the issue
What if my normal levels when I check on diode mode are all higher than 690 in J6620 and grounding (715 in my case) and none of them seem to be way off from that level J6640 and grounding levels are all between 498-501, is that normal also?
This is literly what happen to my ipad the problem is i dont have that many tools Is it possible to share this video to apple so they can fix it One more question when you fix your ipad it will reset all your apps photos or not pls tell me
I am afraid Apple won't do that. But you can find a local third-party repair shop to do that for you. For your question, all the data and APPs would be the same. It won't reset if it's the same problem and the same repairing process.
@@Robert-xo3er I have the facilities and can otherwise buy it for a reasonable price, but I dont trust myself 😂 But on the other hand, Apple is not gonna fix it for me anyways for cheap, because my warranty expired years ago and my iPad doesn't work now anyways, so what can I lose 😂
REWA Technology I wonder , was the original digitazer tested after replacing the chip? Or could it be risky to use it, could it be the reason for the malfunction ? Just curious :)
The touch screen digitizer (white) we installed and tested at last was the original one. At 2:17, another touch screen digitizer was applied to test if the issue was caused by the digitizer.
I am also having problems with my touch in air 3... partially touch freezes for 5 to 10 sec after that it works fine for sometimes....but it happens again and again
Hi, have Ipad 4 and Digitizer almost no response. No damaged but swapped out with new one and same . 99% not responsive and if i rub the screen sometimes it will start working for a few secs and then not . Looked at logic board close up and no obvious damage to components and also reinstalled OS a couple or times and deleted and installed ext in case that was the issue. The black touch filters might be bad but that would stop totally touch? i also pressed down on connector in case that had bad pins/ solder but nothing, I have the Ipad 4 schematics so where should i look at on LB? Thanks for any help..
We do offer training courses. Could you please message us your contact info? We will inform you the details once the next course starts. Any questions and demands please feel free to contact us at: training@rewatechnology.com
Okay, my Ipad Air has a problem. The screen is completely fine, no scratches or something else, but the screen doesnt respond when I want to unlock my ipad or open apps.. What do I have to fix? The LCD + Touchscreen or the LCD or only the touchscreen. Thank you!
1 question... how do you know when hot air soldering the IC already soldered or not... is there any sign? or something?... sorry i make you confuse... (sorry bad english)
Click your heals together 3 times and say “ I wish it was fixed” Or you could take it to an Apple store and have them tell you it needs a new. Logic board and a new screen that will cost $1000. If you want it easy. Lol Dumb question
Все три микроскопа могут взять камеру. www.rewatechnology.com/e-catalog/search/microscopeпожалуйста проконсультируйтесь с нами для получения дополнительной информации: sales@rewatechnology.com
The motherfucker that replaced my broken screen should have seen this video First time he fucks up the Touch ID Second time three rows of screen aren’t responding
Thanks for a great tutorial! Do you know if the approach is similar with the iPad 2018? I have just switched out the glass+digitizer after a cracked screen but now after reassembling it I get a dead spot in the same area as in you video? Can it be remedied in any other way, like pressing on the area connecting the pins or something...? Please help?
Same problem here for iPad Pro 2018. And the dead spot is getting bigger with the time. Were you able to find a solution?
@@charukadewasurendra3347 Yea, it was that the connector for the digitizer wasn't connected properly. So I disconnected and connected again, more thoroughly, and then it worked
I had same issue. I cleaned the connectors on my 2018 ipad6 with 99% alchohol. And tada, the whole screen worked again:). It is the connectors that are not clean or in place.
@@TheVolcomDust I realize your comment is like 2 years old but I have to thank you for posting it. Having just replaced my iPad battery and screen I lost half of the touch functionality, your comment lead me to check the cable connection and the dam thing was a little loose. Thanks because I would have assumed the screen I bought was junk otherwise..
I had dead spots at pretty much the exact same location on an iPad 2018 after a glass/digitizer replacement. Thought either that the new wan was faulty or that the connectors were fried. I also tried with a multimeter and found that two edge pins on the large connector didn't show any resistance, and thought for sure that the iPad was faulty. So I wiggled the pins SLIGHTLY and put the cables back and thought I could take it to an authorized repairer. But then, 3d or 4th time putting it back together it all worked! Maybe it was the wiggle, or maybe I got the cables on more correctly than previous, either way very happy about it.
hi sir, i've recently changed my ipad's touchscreen (same model of ipad) and i have exactly the same dead spots. my best bet is, the repairer didnt do a good job while installing the screen, maybe the same case as yours. could you please tell me what you did to fix the problem? i would appreciate it very much! you can contact me @bryansoon2001@gmail.com, thank you sir !
@@fomor1974 The connectors for the digitizer are really tricky to get right. Think there are about 86 pins between the two that has to line up correctly. Disconnecting and connecting the digitizer cables is fairly easy, but you have to remove the LCD connection to reach them, and before disconnecting the LCD you should disconnect the battery, which I found quite hard the first time, feels like you're about to break it cause you really need to jam a pick (or similar) in there to disconnect the pools. Not to mention before doing any of this you have to disassemble the iPad, removing the glass using suction cup, heat gun and plastic tools to pry it open. My glass was already broken when doing this and by the end it was in pieces. Guess you could take it back to the repairer and argue that the digitizer isn't connected properly and you want to be refunded.
Hey, hows the ipad holding up. have the same issue with mine, fell and screen broke, after replacement, got two dead spots, sent it back to the repair center and nothing, though the new screen works on other ipads so i'm guessing my connections are messed up too.
They did surgery on a ipad
I think REWA has bring great solution ..... loved it
Hi @Rewatechnology
My Ipad Air 3
Touch works preety well at Times and At times part of the touch get stuck/Froze for a few seconds
What do u think could be the issue
What if my normal levels when I check on diode mode are all higher than 690 in J6620 and grounding (715 in my case) and none of them seem to be way off from that level
J6640 and grounding levels are all between 498-501, is that normal also?
Is this the reason why the iPad pro 2017-2019 is having lag and unresponsive touch issues!?
4ksandknives mine move on it’s own but it’s my fault I drop it
This is incredibly annoying, just got a new iPad air and this keeps happening. I thought Apple products were quality.
So the U6650 chip was bad.
Does it work for iPad 5 (2017) too?
This is literly what happen to my ipad the problem is i dont have that many tools
Is it possible to share this video to apple so they can fix it
One more question when you fix your ipad it will reset all your apps photos or not pls tell me
I am afraid Apple won't do that. But you can find a local third-party repair shop to do that for you. For your question, all the data and APPs would be the same. It won't reset if it's the same problem and the same repairing process.
Thanks
Hmm yeah.. I don't think I'm gonna do that xD
Lol I don't got the facilities for that
@@Robert-xo3er I have the facilities and can otherwise buy it for a reasonable price, but I dont trust myself 😂
But on the other hand, Apple is not gonna fix it for me anyways for cheap, because my warranty expired years ago and my iPad doesn't work now anyways, so what can I lose 😂
@@naomiishier 2 years, you still have not fixed it?
@@Robert-xo3er Nah xD
Before logic board solution, some simple methods can be applied to troubleshoot the screen freezing problem. Leave us a comment about your ideas.
REWA Technology I wonder , was the original digitazer tested after replacing the chip? Or could it be risky to use it, could it be the reason for the malfunction ? Just curious :)
Freeze spray or pressing on the chip ?
The touch screen digitizer (white) we installed and tested at last was the original one. At 2:17, another touch screen digitizer was applied to test if the issue was caused by the digitizer.
Hoho
I am also having problems with my touch in air 3... partially touch freezes for 5 to 10 sec after that it works fine for sometimes....but it happens again and again
How to fix iphone 6plus rear camera rattling after fall
Hi, have Ipad 4 and Digitizer almost no response. No damaged but swapped out with new one and same . 99% not responsive and if i rub the screen sometimes it will start working for a few secs and then not . Looked at logic board close up and no obvious damage to components and also reinstalled OS a couple or times and deleted and installed ext in case that was the issue. The black touch filters might be bad but that would stop totally touch? i also pressed down on connector in case that had bad pins/ solder but nothing, I have the Ipad 4 schematics so where should i look at on LB? Thanks for any help..
Try to measure the diode values of the touch connector. If the values are abnormal, you need to replace the touch IC.
@@rewatechnology2008 Hi, did that to the socket pads - to ground and got all .665 roughly or ground so thats seems ok.
So nice I love Rewa..
Does this also work for ipad mini 2?
PLEASE MAKE THE VIDEO FOR IPAD AIR 2 WITH SAME PROBLEM AND POWER PROBLEM AS WELL.
I definitely would travel to you If could buy a course for soldering and reading schemes :D
We do offer training courses. Could you please message us your contact info? We will inform you the details once the next course starts.
Any questions and demands please feel free to contact us at: training@rewatechnology.com
You can also send private message via Facebook: facebook.com/rewatechnology/
In India appeal service center planet care in Bangalore unable to diagnos the deffect and unable to do repairs. Its very sorry state of affairs.
sr subramanian same here so I order iPad new digit zero on Maxbhi.com and replace my self
Will it reset the ipad when we fix the u6670
thank you can you give us online courses if possible
Thanks for the suggestion. It really makes sense and we will definitely consider it. Please stay tuned.
Please respond mr Reba I have a big question please please I’m reallydepressed
Man, this need a lot of tools
IKR
Okay, my Ipad Air has a problem. The screen is completely fine, no scratches or something else, but the screen doesnt respond when I want to unlock my ipad or open apps.. What do I have to fix? The LCD + Touchscreen or the LCD or only the touchscreen.
Thank you!
The problem might be caused by many reasons. It would be better to turn to a repair shop.
1 question... how do you know when hot air soldering the IC already soldered or not... is there any sign? or something?... sorry i make you confuse... (sorry bad english)
eka rusmayana it is about practice under the microscope u can see the around the chip solders are melting is means there is enough heating
@KHAN GAHRAMAN Exactly.
Sir where are you comping located
We are based in Shenzhen , and have branches in US and Czech.
That’s so easy.I will join to rewa if I can do it🤓
If you join REWA, you can do it.
My moto g4 plus touch is broken where can i get parts in cheap price
This will void any warranty, best to just let the company deal with it.
When I will see any Galaxy Smartphone repair Videos ?
Maybe soon. XD
could you please tell me, what music play on this video ?
Bro I kid you not I would do this if I could because my ipad has the EXACT same thing
Bro i have touch issue in ipad air 3 plz resolve it
video is uploaded just now and it shows uplaoded on 9 jan
Vansh Dhir they might of uploaded it yesterday and made it public today. Not sure whats their timezone but that could be a reason as well
It seems the "published on" date on the watch page is based on Pacific Standard Time (PST)， but not GMT (Greenwich Mean Time)
38/5000
I told myself that the designer was left-handed
you just needed to hold the home button and on and off button
Rewa always rock
iam have a question the company REWA is in china or in japan iam confused do not take this comment as offensive
Thanks for the question. We are based in China and have branches in USA and Czech.
Too much work. And how do you disassemble the ipad
MacBook pro graphics repair plz
Um does anyone know a simpler technique
Click your heals together 3 times and say “ I wish it was fixed”
Or you could take it to an Apple store and have them tell you it needs a new. Logic board and a new screen that will cost $1000. If you want it easy.
Lol Dumb question
Porkchop Sandwiches dumb answer bud
Amazing so satisfied working
This wasn't a repair vid it was a replace vid there is a deference
No I'm not doing that.
GOOD JOB BRO
Suparrrrrrr #👌🏻👍🏻😘
The tittle is misleading, this is not a touch screen repair: it's a replacement.
Actually it is a touch screen repair. A repair can have a replacement.
@@husky_violin, in that way, fixing anything would mean replacing it with a new item, which is not the point ;-)
@@tanguero2k7 Note that I used "can." Fixing may also not have replacements.
bravo
Super REWA THNX
Микроскоп без камеры у вас?
Все три микроскопа могут взять камеру. www.rewatechnology.com/e-catalog/search/microscopeпожалуйста проконсультируйтесь с нами для получения дополнительной информации: sales@rewatechnology.com
Я про контент. В видео нет макросъемки.
The motherfucker that replaced my broken screen should have seen this video
First time he fucks up the Touch ID
Second time three rows of screen aren’t responding
Oh boi here we go
and either when we remove the battery
i dropped my screen and it wont work
Genius
IF the whole screen is not working , just change it.
Wsidey EI has nothing to do with the LCD though
To much work.
Here. Is a better solution: Do not buy Apple products!