We installed a metal backsplash in our Kitchen. Here are the steps it took us to do the job. Hope you get something from this video the helps you do your project. Regards, Steve
I'm getting ready to install metal like that for my backsplash and the sides of my built in burners and base of my homemade island. This video answered alot of questions for me in a no bs way that was easily understandable and I thank you sincerely for that. It's about midnight and I'm not stopping till i use all my steel panels up lol night rider!!
So, i see you used plastic boxes. I have metal boxes and am just concerned about using metal boxes having the whole thing grounded, and also about using plastic box extenders as i couldn't ground to the metal box. Would a goof ring work?
Sorry for the delay Kathy, here is what I used. Straight Edge, Scratch Awl, Drill, Screwdriver, Measuring Tape, Plastic Wall Anchors w/ Screws, Angle Grinder, Tin Snips, Metal File, Receptacle Extension Box, Receptacle Screws 1-1/2" Long, Center Punch and Hammer. Hope this answers your question.
Actually just toured a home for sale that did this. the look is unique and different. Something you have to see in person to appreciate. Looks good. I was just wondering if a top clear coat would be necessary after cutting?
Thanks for the comment Johnny. I assume you could coat the cut areas with something made for metal, like a cold galvanize paint to keep it from rusting, but I don't know about a clear coat because it may not stick good enough. I wasn't concerned about that too much because I wouldn't be getting the ends drenched in water to where it would rust, just wiping it down with a wet rag. Maybe if I had an end cap installed to hide the edges, but that could trap water and hold it there. The way I have this it would just run down the backsplash. Some people may like that look too if it did start to rust. Best, Steve
Steve, Any worries about grease splatters behind the stove ? We installed this eon floor to ceiling as backsplash so as to not need tile or ugly plexiglas behind the stove As a new build our cabinets will all be installed next and just a trim board at the top which is at an 8’ high
I wasn't too worried about the grease; we just wipe it down if we see something get on there. Thinking about it though if you do need to clean it with a cleaning product you, would need to make sure it won't affect metal because it could cause streaks.
Hi Garth. Just do a search for "receptacle box extended" and you should get some results from Amazon. They also sell them at Lowes and Home Depot. They come in different sizes depending on how much you need to extend out. You just need to make sure your existing screws are long enough (you can purchase longer screws if necessary) and most importantly, that your existing wires are long enough.
I guess even Crack heads watch home improvement on UA-cam. You know what they say, sometimes it's better to keep your mouth shut and be thought a idiot crackhead than to open it and remove all doubt.
I hope you used box extenders on all the electrical boxes, you would hate to energize the corrugated metal being it’s not bonded to your main electrical service. That would not be a pretty picture
Yes, definitely. I sure don't need to get energized that way. At such a cheap price, it's a shame they are not used more often. Thanks for the comment.
I was gonna ask to , what you used ? To move the outlet out .. do u have a pic of them ? I’ve asked the guys at Lowes an I just get looked at like I crazy .. Thx for any help
Not sure why you used so many screws but I did this with just liquid nails and caulked the edges and it looks way better than this. The screws ruin the clean look of the finished product and are totally unnecessary. However, your video and fitting skills were very good!
I totally disagree, the screws give it a utilitarian look that you couldn't get using retainers or liquid nails. And good luck with your liquid nails after a few months of humidity and condensation if it's a back splash or even in a kitchen as you'll be screwing it in place eventually anyway
I'm getting ready to install metal like that for my backsplash and the sides of my built in burners and base of my homemade island. This video answered alot of questions for me in a no bs way that was easily understandable and I thank you sincerely for that. It's about midnight and I'm not stopping till i use all my steel panels up lol night rider!!
Oh man, thanks for the kind words and your very welcome. I am glad you got something from it. Hope it turns out good for you.
Love this...gonna do this as a splash back in my campervan. Thanks for sharing 😊
Sounds like a good idea and should go nicely with the pallet wood. Looks like a fun project, good luck.
@steveshome thanks ...its going to be very rustic once it's done...stay tuned
great work and tutorial. thanks for sharing man
Your welcome, hope it helped.
I loved this content it was very helpful and you were so peaceful. I can do it !! 😊
So, i see you used plastic boxes. I have metal boxes and am just concerned about using metal boxes having the whole thing grounded, and also about using plastic box extenders as i couldn't ground to the metal box. Would a goof ring work?
I am no electrician so I don't really know if what you mean is safe or not. Sorry.
What supplies did you need ? It's hard to hear you at times.
Sorry for the delay Kathy, here is what I used. Straight Edge, Scratch Awl, Drill, Screwdriver, Measuring Tape, Plastic Wall Anchors w/ Screws, Angle Grinder, Tin Snips, Metal File, Receptacle Extension Box, Receptacle Screws 1-1/2" Long, Center Punch and Hammer. Hope this answers your question.
Actually just toured a home for sale that did this. the look is unique and different. Something you have to see in person to appreciate. Looks good. I was just wondering if a top clear coat would be necessary after cutting?
Thanks for the comment Johnny. I assume you could coat the cut areas with something made for metal, like a cold galvanize paint to keep it from rusting, but I don't know about a clear coat because it may not stick good enough. I wasn't concerned about that too much because I wouldn't be getting the ends drenched in water to where it would rust, just wiping it down with a wet rag. Maybe if I had an end cap installed to hide the edges, but that could trap water and hold it there. The way I have this it would just run down the backsplash. Some people may like that look too if it did start to rust. Best, Steve
Steve,
Any worries about grease splatters behind the stove ? We installed this eon floor to ceiling as backsplash so as to not need tile or ugly plexiglas behind the stove
As a new build our cabinets will all be installed next and just a trim board at the top which is at an 8’ high
I wasn't too worried about the grease; we just wipe it down if we see something get on there. Thinking about it though if you do need to clean it with a cleaning product you, would need to make sure it won't affect metal because it could cause streaks.
How did you get your outlets to come out farther? Mine are flush with the drywall and I need to make them come out farther
Hi Garth. Just do a search for "receptacle box extended" and you should get some results from Amazon. They also sell them at Lowes and Home Depot. They come in different sizes depending on how much you need to extend out. You just need to make sure your existing screws are long enough (you can purchase longer screws if necessary) and most importantly, that your existing wires are long enough.
Amazing!! Congrats for the result!!
How did you know where to cut for the outlet box?
Careful measuring from the edge of the wall, the bottom of cabinets and the countertop. Then measured it again to double-check.
Love it
What size Receptacle Outlet Box Extenders did you use?
Sorry for the delay, Bill. I used the 1/2" extenders. That size fit the metal panels I used pretty well.
Is this the roofing metal? We just redid our countertops and this is next.
Yes, it is. I purchased it from a big box store.
Is it metal? Are you serious... What do you think it would be after watching that? Cardboard? What a dunce!
I guess even Crack heads watch home improvement on UA-cam. You know what they say, sometimes it's better to keep your mouth shut and be thought a idiot crackhead than to open it and remove all doubt.
I hope you used box extenders on all the electrical boxes, you would hate to energize the corrugated metal being it’s not bonded to your main electrical service. That would not be a pretty picture
Yes, definitely. I sure don't need to get energized that way. At such a cheap price, it's a shame they are not used more often. Thanks for the comment.
I was gonna ask to , what you used ? To move the outlet out .. do u have a pic of them ? I’ve asked the guys at Lowes an I just get looked at like I crazy .. Thx for any help
Wow! That stuff is paper thin. The stuff l have came off an old roof. It's about the thickness of a '65 VW Bug.
You didn't show how the wood was on bottom
Sorry Maichelle, I don't understand what your asking about? Please clarify and I will try to answer.
What? 👂
Not sure why you used so many screws but I did this with just liquid nails and caulked the edges and it looks way better than this. The screws ruin the clean look of the finished product and are totally unnecessary. However, your video and fitting skills were very good!
I totally disagree, the screws give it a utilitarian look that you couldn't get using retainers or liquid nails. And good luck with your liquid nails after a few months of humidity and condensation if it's a back splash or even in a kitchen as you'll be screwing it in place eventually anyway
@@jessjohnson-rocks ok Bob Villa