Always nice to see how other places to it. We do ours a little different. We strip the outer jacket until a few inches above the conduit. But a water seal around it and that cable is so much more flexible. Also we twist the bleeder wire on to the concentric and wrap it going up the elbow before landing it. Solid video. Always wondered how these elbows differ from other styles.
Well done, 2 things that got in my mind during the video. First, the press fittings that I know had to be started all the way back and than the second, third, fourth towards the lug. In that way you'll force the conductor into the press fitting and create additional contact area at the conductor face. It might not be important on small connectors like this, but definitely on 1000+ amps. Second thing the grease/clay inhibitor, you want to have the full amount of it inside the press fitting to guide heat out of the core and transfer it into the lug. Beside the temperature thing you also make sure that humidity has no chance to enter even if the outer isolation fails over the years.
Any tips? I’ve been doing underground for a few years but my company wouldn’t put ug guys through apprenticeship only guys in the building. Going to do it on my own
@@GageDunnbar be persistent, if you want to get into a apprenticeship program find contractors that offer an apprenticeship program as a benefit. I work for a tier one contractor for a major north Texas co-op. Also, don’t be discouraged to start off using a shovel again.
You should press the lug on before you make the 6 7/8” measurement. That also is the only measurement that has to be precise. After you should use SAP tape from the jacket to the elbow before you connect the bleeder wire to eliminate the possibility of water getting into the elbow.
He is not using an electrician's back reading folding rule? Okay. I used to let those banana peelers and spiral cutters fall on the ground and just score it with a prep knife. After the 500th termination you have it dialed in pretty well. Heating that mess up with the weed burner make it lots easier to work with too. Aluminum oxidizes immediately when it contacts air. If you score into the insulation you can sand or file the scored part back smooth. My oldest stress cone tools are made like Vise Grips with a pull handle on one jaw and blades that cut a square cut and drag a parallel cut like the banana peelers. Those are some really OLD tools. They served me very well, if I bothered to use them.
You installed your silicone grease from your semi-con over the exposed insulation, if you were working for me, you would be cleaning that again and doing it over. Also, with a little a practice, and experience you can make all your scores and cuts with a sharp knife with more accuracy. When you ring cut the cable jacket, "break" the score with 2 hands and remove the jacket toward your butt cut and there is no need to worry about bird caging the concentric.
@@jarredcorby7170 yes I know how to use a knife. Been doing this a long time. Maybe the semi-con you get is more cooperative. The stuff I get is extremely difficult to remove without the proper tool.
Whenever you start doing nonessential tasks for the sole purpose of aesthetics then you have strayed from the path of a competent installer. "Gee Bob, look how much time Mr. Smith wasted making this elbow look a certain way even though it made no difference in performance or safety." Good thing most linemen work for the public where they are not held accountable for their productivity.
Listen here Tommy… Real closely! I can’t terminate anything I’m sure faster than you with the highest quality of craftsmanship. I’ve been a lineman for 18 years dude and worked with them all. Number 1 is efficiency and second close is quality of work. I’m not cocky but a comment like this usually means you do really scab quality work.
Nonsense. A nice clean and orderly installation is important. Makes it easier to see what's going on and make changes or additions in the future. Imagine working with a rat's nest and checking things over.
People like you really make UA-cam a valuable tool. Thanks for taking the time so share your knowledge.
Always nice to see how other places to it. We do ours a little different. We strip the outer jacket until a few inches above the conduit. But a water seal around it and that cable is so much more flexible. Also we twist the bleeder wire on to the concentric and wrap it going up the elbow before landing it. Solid video. Always wondered how these elbows differ from other styles.
Well done, 2 things that got in my mind during the video. First, the press fittings that I know had to be started all the way back and than the second, third, fourth towards the lug. In that way you'll force the conductor into the press fitting and create additional contact area at the conductor face. It might not be important on small connectors like this, but definitely on 1000+ amps. Second thing the grease/clay inhibitor, you want to have the full amount of it inside the press fitting to guide heat out of the core and transfer it into the lug. Beside the temperature thing you also make sure that humidity has no chance to enter even if the outer isolation fails over the years.
Just started off as a UG apprentice very informative video. Thank you sir.
Any tips? I’ve been doing underground for a few years but my company wouldn’t put ug guys through apprenticeship only guys in the building. Going to do it on my own
@@GageDunnbar be persistent, if you want to get into a apprenticeship program find contractors that offer an apprenticeship program as a benefit. I work for a tier one contractor for a major north Texas co-op. Also, don’t be discouraged to start off using a shovel again.
The V part of that probe tool is used so the wire sets it’s self along the wire and you can use a ratchet motion to strip back that jacketed neutral!!
Solid videos dude. A lot of good pointers 👍🏻
All good but one tip for those working in a hot tx. Make sure to keep those concentric away from anything that ain't equipotential to ground.
Thank you for posting this.
Hello, what chamfering tool is that? the one that is made for that cable alone?
This was very informative. Loved it
Great work!
I like this guy's attitude, make it perfect. Never put your name on slop.
How do you make a solid ring cut in with the bananna peeler
Use a pipe cutter
AWESOME helpful video!
What is the brand and part number for the pre-determined chamfer tool ?
To be honest I couldn’t tell ya sorry bud
You should press the lug on before you make the 6 7/8” measurement. That also is the only measurement that has to be precise. After you should use SAP tape from the jacket to the elbow before you connect the bleeder wire to eliminate the possibility of water getting into the elbow.
He is not using an electrician's back reading folding rule? Okay. I used to let those banana peelers and spiral cutters fall on the ground and just score it with a prep knife. After the 500th termination you have it dialed in pretty well. Heating that mess up with the weed burner make it lots easier to work with too. Aluminum oxidizes immediately when it contacts air. If you score into the insulation you can sand or file the scored part back smooth. My oldest stress cone tools are made like Vise Grips with a pull handle on one jaw and blades that cut a square cut and drag a parallel cut like the banana peelers. Those are some really OLD tools. They served me very well, if I bothered to use them.
You installed your silicone grease from your semi-con over the exposed insulation, if you were working for me, you would be cleaning that again and doing it over. Also, with a little a practice, and experience you can make all your scores and cuts with a sharp knife with more accuracy. When you ring cut the cable jacket, "break" the score with 2 hands and remove the jacket toward your butt cut and there is no need to worry about bird caging the concentric.
No robo presses? Wow. Do you use ratchet cutters still? And that’s xlp cable. That isn’t used anymore where I work.
Great video but I’m pretty sure you have to measure your 6 7/8 after you have already pressed your copper top.
Where did you get the chamfering tool at?
you work at abb?
Work that looks good works good
where are your PPE steel toe boots ?
I didn’t tell ya?
@@allanedmondson641 not once XD
@@SgtStarSlayer because it’s none ya damn business. 🤘🏻
@@allanedmondson641 lawls, when Osha says otherwise and shut that site down. You will moaning even harder.
Why not use a regular splicing knife, you don’t need all those fancy stripping tools.
Because I like using them.
Yes you do. Just try getting that semi-con off without the special tool. It is incredibly difficult.
@@ethanbrush4932 Not really, if you know how to use a knife.
@@jarredcorby7170 yes I know how to use a knife. Been doing this a long time. Maybe the semi-con you get is more cooperative. The stuff I get is extremely difficult to remove without the proper tool.
I agree 100%, faster and more accurate.
How many hours you doing terminate in 1 elbow?
I can’t term an elbow, land it with ring buss done in 7 minutes
Or measure 200mm
Why wipe off the inhibitor? It's there for a reason.....
5:12 Don’t take off your PPE 😂
Pretty dangerous putting on some tape. 🤓
follow the instructions in the elbow package ...can't go wrong ...
Excelencia y más
Checks out
comme chez nous en france
Great video!! They are called Linesman pliers not Kleins. Klein makes them. Just busting balls.
They are called Klein's, 9's. and side cutter's. LOL
@@jaymes7521 wat side cutters are diagonal pliers....tool names are cursed lol
Whenever you start doing nonessential tasks for the sole purpose of aesthetics then you have strayed from the path of a competent installer. "Gee Bob, look how much time Mr. Smith wasted making this elbow look a certain way even though it made no difference in performance or safety." Good thing most linemen work for the public where they are not held accountable for their productivity.
Listen here Tommy… Real closely! I can’t terminate anything I’m sure faster than you with the highest quality of craftsmanship. I’ve been a lineman for 18 years dude and worked with them all. Number 1 is efficiency and second close is quality of work. I’m not cocky but a comment like this usually means you do really scab quality work.
Nonsense. A nice clean and orderly installation is important. Makes it easier to see what's going on and make changes or additions in the future. Imagine working with a rat's nest and checking things over.
Just a little hard to watch.
Then don’t
Hold. The. Phone. HORIZONTALLY. For the love of god.
Vertical video is a sin. Repent...
Sand it, if you cleaning it from the top to semicon, that is standard.
Use the plier all the way to ring cut.
Armando.nieblapasswordpassqordpassqordoasswordpassqordpassqordpassqordpasswordpssqordpassordpasswordpassqordpassqordpaasqordpassqord