I agree with Abraham Cosworth: "When you build a three-wheeler, the two-wheeler should always be the front axle." If you build it like the one in this video you will tip over at the slightness curve when braking. A friend of mine broke his arm riding one like the one pictured above. He was braking on a curve. He is lucky to have lived to tell about it.
Witam z Polski szalony to jesteś nie źle spawasz tylko w okularach bez osłony na dłonie zachorujesz na raka skóry , kości będziesz umierał w cierpieniach a jeszcze jesteś młody życie przed Tobą pozdrawiam zmień swoje postepowanie
Back wheels are likely to come off as he welded the fittings to hold them on top instead of the more secure, and more likely the safest place of underneath. Because of this, its a potential death trap!
Try making a dually trike. I made one, it was weird, but I got the hang of her and I ended up out running my friend Yako's Yamaha Banshee through a field. I built my own suspension system with the frame. It was a wild lil trike. Everone an they brother tried to buy it or steal it. But not one person got it. Eventually I ended up sliding off a road an into a ditch going 53 mph. Totally destroyed it, I braced myself an had a helmet on an ended up with a cut an bout 4 bruises. Dragged it home on foot an hung it up in a tree where it rots to this day. My cousin jus took a picture of it last week, she never knew it was there.
I guess he can easily flip it upside down and remount the seat , engine, etc..but I totally agree , if the welds happen to break it would be much safe, not that it’s safe to begin with .
По моему крайне сомнительная конструкция ! Во первых профильную трубу надо ставить рубака , во вторых крепление задних колёс вообще отстой , если у самого соображалка не работает то посмотри как крепятся колёса на велосипеде или мотоцикле !
i'd like to for once see one of these builds WITHOUT the use of a welder, or other bench powertools. being some people don't have access to a shop to use ether of these things.
Its a good idea but yoy must put support in the attachement of your front wheel to the chassis and also the attachment of your rear wheel (ehe) it must be under your chassis because when your volt and knot getting lose you will fall down.
May I suggest using the fattest wheels you can find, like from a schwinn stingray (the latest one) or from a motorcycle. Also, add a second, top bar, connecting the bike part to the frame. That will make it harder for that part of the trike to bend, as well as making it sturdier. Nice job.
First you should have 2 wheels on the front one in the back, you only have power to one wheel. Well if you only have parts for a single front wheel. Second, flip your frame over, then your weight keeps the car on the axle not pushing off of the axle. Third, mount your moter to the rear. Save space to mount seat. Nice to see people make fun and useful things.
Trikes were banned in the US... basically because of the unstable behavior you can see here, 2 weeks or 4 wheels > 3 wheels for stability since the force can make its way to a wheel in any situation whereas in many situations a trike will want to flip. The only trikes you can buy in the US now, are reverse trikes with 2 wheels at the front because they are more stable when stopping and turning.
Tom Squires: Really.... Awesome work. So what do you call it when someone makes a similar project with suitable wheels to take any load and any type of turns? Awesome to me would be 100% success with no flaws or failures.
@@kassiedreaneai7459 building with what you have and learning is the awesome part. You have to start somewhere. He has braved the comments of the internet to show his skills. 100% success is not always achieved the first time.
@@kassiedreaneai7459 something can still be awesome without being perfect. For a first attempt this is awesome, but there is defiantly room for improvement in the future
This waa really exciting when Benz, Olds and Henry Ford built them 135 years ago. It elludes me why people film themselves doing in 2020 with a Harbor Freight generator/mower motor. Nice construction. Hope you're enjoying the drives.
ВЫ ВНИМАТЕЛЬНО ЧИТАЛИ НАЗВАНИЕ РОЛИКА ? ОН ПОКАЗЫВАЕТ ЧТО И В ДОМАШНИХ УСЛОВИЯХ (НА КОЛЕНЯХ) МОЖНО ДЕЛАТЬ ВЕЩИ . ПОТОМ К ЭТОМУ СТОЛУ ВЫ СКАЖИТЕ А ГДЕ ТОКАРНЫЙ С ЧПУ ? МОЛЧИТЕ И СМОТРИТЕ КАК УМЕЛЬЦЫ С МИНИМАЛЬНЫМ И ПРОСТЫМ ИНСТРУМЕНТОМ ДЕЛАЮТ ТАКИЕ ВЕЩИ .
Il y a encore des pays où l'on peu se faire plaisir en fabriquant des engins de ce genre. Mais en France ce n'est même pas la peine d'y penser, sauf si le véhicule passe d'abord aux contrôle des mines et ce n'est pas gratuit.
Muy bueno...solo un detalle...los ejes d las ruedas traceras deverian ir por debajo...para q no se salgan...x q d la manera q estan puestas....agarras un bache y quedas en el piso...
u need a smaller back sprocket you will burn out your clutch the motor but you will have good top speed but you should change it to a toque converter but good viedo well done otherwise
Cool. But, i noticed you didnt show any vids of starting from a complete stop. Im certain you needed your feed to push off.. or burn the clutch. NEED gear reduction.. as you are aware.
O erro na engenharia esta nas rodas traseiras! O quadro tem de ser apoiado sobre os eixos das rodas para que as mesmas não se soltem. Da forma como foi colocadas as rodas vai ter um momento que poderão soltar-se e o quadro ir ao chão!
Tienes razón esa mierda no va aguantar el un viaje a grande distancia tan sólo el tubo de la dirección delantera no aguantara las vibraciones nisiquiera le puso sortes para aguanta su propio peso y apuesto todo lo que quieras que esos riines al pasar un tope de lado o ir algo rápido en un camino inestable sus rrines quedaran todos chuecos como el no entiendo aun el porque los tubulares de la parte tracera están por enzima cuando los pudo cortar a medida y le ubiese quedado mejor y mas resistente sillo isiera uno de esos le pondría suspensión en las tres llantas
a grinder and paint make him a wielder he aint .....and did you notice the wheel stays in the back are on the wrong side? wheel nuts come loose and wheel will fall out
I love his creativity but please don't put the rear wheels on with the frame slots openings facing up. You are going to literally "Drive wheels right off"....lol.
I would think the front is not very secure, would need rear brakes, probably rear fat tires and wheels, and a solid rear axle, so it's not pulling from just one side, and a bit longer,
Brave guy! Cuts without glasses, holds the details with his fingers!
I agree with Abraham Cosworth: "When you build a three-wheeler, the two-wheeler should always be the front axle." If you build it like the one in this video you will tip over at the slightness curve when braking. A friend of mine broke his arm riding one like the one pictured above. He was braking on a curve. He is lucky to have lived to tell about it.
How about if you make the wheel in front bigger than the wheels in the back? Do you think that would help?
@@noyb7214 No, sorry. Having a bigger wheel in front will not help.
Yes
*I bought this trike so I could play outside with my 3 children. Tricycle **Latest.Bike** is well built and fun to ride. Great purchase overall!*
Where did u buy it ??
Another great little project, I think I have every thing needed to build this in my neighbors back yard lol .
E
Потратить столько времени на разработку и сборку изделия, чтоб потом в позе зародыша ездить на этом транспортном средстве. Это круто.
Так у него ещё и колёса вылетают)))
Witam z Polski szalony to jesteś nie źle spawasz tylko w okularach bez osłony na dłonie zachorujesz na raka skóry , kości będziesz umierał w cierpieniach a jeszcze jesteś młody życie przed Tobą pozdrawiam zmień swoje postepowanie
When you build a three-wheeler, the two-wheeler should always be the front axle.
Yep, and by that point... just build a 4 wheeler.
Back wheels are likely to come off as he welded the fittings to hold them on top instead of the more secure, and more likely the safest place of underneath. Because of this, its a potential death trap!
Yep, brackets underneath and smaller wheels geared accordingly for better strength & stability.!!
Try making a dually trike. I made one, it was weird, but I got the hang of her and I ended up out running my friend Yako's Yamaha Banshee through a field. I built my own suspension system with the frame. It was a wild lil trike. Everone an they brother tried to buy it or steal it. But not one person got it. Eventually I ended up sliding off a road an into a ditch going 53 mph. Totally destroyed it, I braced myself an had a helmet on an ended up with a cut an bout 4 bruises. Dragged it home on foot an hung it up in a tree where it rots to this day. My cousin jus took a picture of it last week, she never knew it was there.
Frame should be mounted above wheels, nuts come loose but won't slip out of slot.
I guess he can easily flip it upside down and remount the seat , engine, etc..but I totally agree , if the welds happen to break it would be much safe, not that it’s safe to begin with .
По моему крайне сомнительная конструкция ! Во первых профильную трубу надо ставить рубака , во вторых крепление задних колёс вообще отстой , если у самого соображалка не работает то посмотри как крепятся колёса на велосипеде или мотоцикле !
i'd like to for once see one of these builds WITHOUT the use of a welder, or other bench powertools. being some people don't have access to a shop to use ether of these things.
I would’ve put knobby go kart tires in the rear, like a big wheel. Still a cool build!
Now I wish I hadn't thrown away all my bicycles. I could have made several karts.😬👌👍
Vdgfggh
Its a good idea but yoy must put support in the attachement of your front wheel to the chassis and also the attachment of your rear wheel (ehe) it must be under your chassis because when your volt and knot getting lose you will fall down.
May I suggest using the fattest wheels you can find, like from a schwinn stingray (the latest one) or from a motorcycle. Also, add a second, top bar, connecting the bike part to the frame. That will make it harder for that part of the trike to bend, as well as making it sturdier. Nice job.
It is floppy, a good corner would wreck it, it’s a great idea though.
First you should have 2 wheels on the front one in the back, you only have power to one wheel.
Well if you only have parts for a single front wheel.
Second, flip your frame over, then your weight keeps the car on the axle not pushing off of the axle.
Third, mount your moter to the rear. Save space to mount seat.
Nice to see people make fun and useful things.
20:08 задние колёса закреплены не правильно! На первой хорошей кочке отлетят от рамы! Рама должна лежать на оси колеса ,а тут колесо на раме.
right
Всю раму нужно перевернуть, а то вся сварка идет на разрыв
Это от начала до конца: " инструкция как не нужно делать!"))
👏👏👏👍👍👍 тоже хочу но 2-х движков.молодца
How are you supposed to change the tires If they become flat
Don't you think the axles should have been underneath the frame so if they loosen up they don't fall out
Нравятся ролики , где человек показывает место сварки , а не сверкает половину ролика!
Awesome job but your axle perches are upside down so with weight and a bump your tires will fall off
I think I will build myself a joy toy home made.
Hope the weld don't fracture when he driving down a steep hill.
Trikes were banned in the US... basically because of the unstable behavior you can see here, 2 weeks or 4 wheels > 3 wheels for stability since the force can make its way to a wheel in any situation whereas in many situations a trike will want to flip. The only trikes you can buy in the US now, are reverse trikes with 2 wheels at the front because they are more stable when stopping and turning.
Great build! Be careful with the tight turns the rear wheels may fold on you. A composite wheel my be stronger. Keep up the awesome work!
Tom Squires: Really.... Awesome work. So what do you call it when someone makes a similar project with suitable wheels to take any load and any type of turns? Awesome to me would be 100% success with no flaws or failures.
@@kassiedreaneai7459 building with what you have and learning is the awesome part. You have to start somewhere. He has braved the comments of the internet to show his skills. 100% success is not always achieved the first time.
qual e esse motor que vc usou
@@kassiedreaneai7459 something can still be awesome without being perfect. For a first attempt this is awesome, but there is defiantly room for improvement in the future
ого цех эй щи чо
angle grinding without glasses, such a genious
Deutschland im Jahr 2025 , auf dem neuesten Stand der Technik .
mas peso se saldrá las llantas de atrás (el hueco para ajustar las llantas tienen que ver hacia abajo )
la vibración del motor, expulsa la llanta. Tenga precaución.
die halterrung für die hinteren räder falsch rum ,richtiger hügel plus gewicht= würden die rausflutschen^^
прикольно,но если нет педалей это не велосипед :)просто мототрайк с ужасной посадкой ног
This waa really exciting when Benz, Olds and Henry Ford built them 135 years ago. It elludes me why people film themselves doing in 2020 with a Harbor Freight generator/mower motor.
Nice construction. Hope you're enjoying the drives.
You negativity spouting tard, nobody gives a fcuk what people where doing 135 yrs ago.
Голова и руки растут откуда надо👍. Здоровья и дальнейших успехов!
Ну да из ЖОПЫ !
Put a primary shaft before the gears on the bike and you can have both tires pull instead of just one
No saftey goggles were harmed in the making of this video
ты бы стол сделал..поверь мне на нем намного удобней все делать)))
ВЫ ВНИМАТЕЛЬНО ЧИТАЛИ НАЗВАНИЕ РОЛИКА ? ОН ПОКАЗЫВАЕТ ЧТО И В ДОМАШНИХ УСЛОВИЯХ (НА КОЛЕНЯХ) МОЖНО ДЕЛАТЬ ВЕЩИ . ПОТОМ К ЭТОМУ СТОЛУ ВЫ СКАЖИТЕ А ГДЕ ТОКАРНЫЙ С ЧПУ ?
МОЛЧИТЕ И СМОТРИТЕ КАК УМЕЛЬЦЫ С МИНИМАЛЬНЫМ И ПРОСТЫМ ИНСТРУМЕНТОМ ДЕЛАЮТ ТАКИЕ ВЕЩИ .
@@СССРИРКУТСКкаждому свое
Il y a encore des pays où l'on peu se faire plaisir en fabriquant des engins de ce genre. Mais en France ce n'est même pas la peine d'y penser, sauf si le véhicule passe d'abord aux contrôle des mines et ce n'est pas gratuit.
Buena explicacion quisiera hacerle una pregunta no se le podran adaptar unos amortiguadores gracias Dios me lo siga bendiciendo
Se podrá
Qué bien trabajo amigo felicitaciones adelante guerrero
e uno dei veicoli più fantasiosi del secolo il prossimo video lo voglio vederlo al MCdrive per favore
great build. didn't show the drive train. makes me sad.
How not to build a three wheeled motorized bike...
Let’s see yours. Bud
I think it's awesome. Show us the one you built?
Шикарно!!!
А можно поподробней по установке двигателя?
Ну класс, тока колени немного упираются в подбородок...
Cool! Thanks!
Very cool!! Thanks for the upload!!
Wow..สุดยอด..เอามันแบ่บเนี่ย..โดน👍👍👍
a good job, efficient delivery trucks
Good Job 👍
Muito legal que Deus te abençoe
He is using a geared output engine, but even so, it is too fast for comfort. He should be using a jackshaft to keep the speed within reason.
Dangerous 🤣🤣🤣but a lot of fun
Front ends going to snap, needs more bracing
Muy bueno...solo un detalle...los ejes d las ruedas traceras deverian ir por debajo...para q no se salgan...x q d la manera q estan puestas....agarras un bache y quedas en el piso...
Very nice good idea I think I'll try it!
Super !
Excelente
Hola esta muy bien tu proyecto . Que le puso en el eje del motor para la cadena dar movimiento.
Soo viel Werbung keine Lust das Video bis zum Schluss zu schauen 👎
Really nice build
под каким углом он переднюю вилку приварил на повороте обод и колесо согнется
Не хватает амортизации
Do you think this could be built all bolted together instead of welded? I am not much of a welder
u need a smaller back sprocket you will burn out your clutch the motor but you will have good top speed but you should change it to a toque converter but good viedo well done otherwise
thank you
Мне понравилось.Не помеалобы глушитель поставить.Какая скорость у тебя на нем?
Show parabéns 👏 Álvaro/ Regina
Wouldn't the back tires just fall out of the slots were they are mounted in???
Сваркой поперёк поперерезал все профили ))
Ótimo.. Bem criativo... Que motor é esse..?? Obrigada....
MOTOR BUFALO,BRANCO,TUDO SERVE
Legal... só não gostei das fixações das rodas traseiras... parece que deveriam estar na parte inferior, virados pra baixo...
Hola amigo ya lo tengo pero no se como conectar acelado y freno por favor puede hacer un Toturial se lo agradeceré mucho
Bicicleta seria se tivesse duas rodas. Se tem três rodas. Você construiu um triciclo motorizado.
Cool. But, i noticed you didnt show any vids of starting from a complete stop. Im certain you needed your feed to push off.. or burn the clutch. NEED gear reduction.. as you are aware.
Put the measurements for each part and the dimensions of the holes, if you please
Very nice 3 wheeler 👍🏻
great bro
thanks
I like it and I want to know where did buy the motor
O erro na engenharia esta nas rodas traseiras!
O quadro tem de ser apoiado sobre os eixos das rodas para que as mesmas não se soltem.
Da forma como foi colocadas as rodas vai ter um momento que poderão soltar-se e o quadro ir ao chão!
Tava aqui pensando a mesma coisa qnd li o seu comentário haha
Идеальная машина....для яркого самоубийства!
Ездить можно,но только медленно,и то на ровной дороге.Ну,а там ,как повезет...
Clutch on engine, is a scooter rear variator? If so, how did you mount?
Exelente video tengo un motor 125 cc arranque electrico y embrague automatico construire uno gracias por el video estoy muy motivado,
Que te valla bien tu proyecto
Just add pontoons and paddles on the spokes!
I’m trying to use the sprockets off 10 speed bike on mini bike and still swicth gears, I’m stuck on what size chain to use
Können sie sich damit auch im Straßenverkehr bewegen, oder nur auf geheimen Waldwegen??
Onde encontrar estes veículos?
Un motor tan grande para una sola persona es un desperdicio pero bueno esa fue su intencionbien por la intencion y el esfuerzo
Ese motor de que maquina es felicitaciones
Yo hubiera puesto las bases de las gomas de atrás por abajo tendría más seguridad que no se salga una goma
Tienes razón esa mierda no va aguantar el un viaje a grande distancia tan sólo el tubo de la dirección delantera no aguantara las vibraciones nisiquiera le puso sortes para aguanta su propio peso y apuesto todo lo que quieras que esos riines al pasar un tope de lado o ir algo rápido en un camino inestable sus rrines quedaran todos chuecos como el no entiendo aun el porque los tubulares de la parte tracera están por enzima cuando los pudo cortar a medida y le ubiese quedado mejor y mas resistente sillo isiera uno de esos le pondría suspensión en las tres llantas
Tienes razón no había caído en cuenta por abajo más seguro porque el peso lo ajusta, por arriba queda fui dando y un poquito que se afloje se desarma.
Can you tell what material required for making this
A los que haceis estos videos, donde aprendisteis a soldar??!! Porque yo en esa bici no me monto ni loco....
Muito legal amigo
Me gustaría tener una bicicleta así como esa.
También yo
Vila to dobře doufám že bude i tak dobře jezdit
Wow that good idea sir i think i want to make one watching from philippines 6 7 2020 sir can you give me all mesure u cut pls
don't go back and forward over the finished weld no welder does that and i wasen't taught that
a grinder and paint make him a wielder he aint .....and did you notice the wheel stays in the back are on the wrong side? wheel nuts come loose and wheel will fall out
Could you please tell me the Width andLlength of this bike frame
Better yet have a motor and driving both wheels thereby rearranging the motor or engine plus 2 seats would be great
Boa tarde amigo lindo projeto
I love his creativity but please don't put the rear wheels on with the frame slots openings facing up.
You are going to literally "Drive wheels right off"....lol.
Bikes have 2 wheels; trikes have 3 wheels
I would think the front is not very secure, would need rear brakes, probably rear fat tires and wheels, and a solid rear axle, so it's not pulling from just one side, and a bit longer,