FWIW, this motor fixed my transfer case problems. I was having terrible grinding noises, car dropping out of gear, not going into gear, making huge clunks as it semi engaged in gear and lurched forward. I thought my chain drive was stretched/screwed but I didn't want to tear into the transfer case to diagnose or replace the hole thing. This fixed it all. Your mileage may vary lol. 2008 WK 4.7L
Great video. My replacement motor dosent line up, holding the old next to the new the little "line-up" notches are Not in the same positions. Thoughts on how I could line up the new one? Thank you for your time.
I noticed that you didn't re install the locator plug that is in the bolt hole of the motor that you removed, you can see it at 1.35 in the video, and at 1.50 it is not there on the new motor install. Will this matter ?
Would this part fix my transfer case from it coming out of first gear? My 06 4.7 will go in first but won’t come out of first gear and will rev high and not go into second, thank you
Love the video, I'm having some issues with my transfer case. When I do yhe remote start I hear like a clicking sound then goes away. Then hear it again after I turn or park. You think it's the transfer case motor?
My case stopped shifting service light is on can't reset I haven't got under to verify wiring harness to be ok but I'm assuming shift motor died so can't shift to low or into neutral so I'm assuming to line this up I'd just jack up the vehicle to remove tension off drive shafts and turn the spline by hand until case is neutral then install new shift motor ?
Hello 👋🏾, I have a 08 wk 3.0 that won't go into 4Hi. But will drive in 4Lo I'm hoping this will fix my problem. It just went out all of a sudden on a washboard road.
Does this fix the grinding noise that comes and goes from the transfer case area? I’m not sure if it is the transfer case but I’m hearing a grinding from the rear of my 07 overland, the noise comes and goes
Can a bad Transfer case shift motor puts my car into limp mode? I am getting C140F code "Transfer case range position sensor erratic performance". Randomly I get Transmission Over Temp and the 05 WK 5.7 would go into limo mode (gear# 3). Ive been struggling for 2 weeks to find whats really causing this issue. Thank you
Janek vangonin And I have one question, when I turn off the ESP, it starts to make noise down there. when I turn ESP back on, the sound disappears. and when I accelerate, the . Hi do you have Transfer case 146 SRT jeep crand cherokee 6.1 4x4 SRT8 2008 WIN : 1J8HCE8368Y105329
+UnknownElementzZ This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
I know you probably won't reply to my comment but how the heck do you get the gear in the correct position to install the new motor? Everytime I try to put it in neutral, the gear is in the wrong position. And at one point I couldn't get my Jeep out of neutral.
+ARC Bonez2520 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
FWIW, this motor fixed my transfer case problems. I was having terrible grinding noises, car dropping out of gear, not going into gear, making huge clunks as it semi engaged in gear and lurched forward. I thought my chain drive was stretched/screwed but I didn't want to tear into the transfer case to diagnose or replace the hole thing. This fixed it all. Your mileage may vary lol. 2008 WK 4.7L
Why did it fail? What were the symptoms?
Great video. My replacement motor dosent line up, holding the old next to the new the little "line-up" notches are Not in the same positions. Thoughts on how I could line up the new one? Thank you for your time.
I noticed that you didn't re install the locator plug that is in the bolt hole of the motor that you removed, you can see it at 1.35 in the video, and at 1.50 it is not there on the new motor install.
Will this matter ?
Would this part fix my transfer case from it coming out of first gear?
My 06 4.7 will go in first but won’t come out of first gear and will rev high and not go into second, thank you
Thanks for the knowledge
+Yung Bitta Thanks for watching our video! 1aau.to/m/Shop-TRQ
Love the video, I'm having some issues with my transfer case. When I do yhe remote start I hear like a clicking sound then goes away. Then hear it again after I turn or park. You think it's the transfer case motor?
My case stopped shifting service light is on can't reset I haven't got under to verify wiring harness to be ok but I'm assuming shift motor died so can't shift to low or into neutral so I'm assuming to line this up I'd just jack up the vehicle to remove tension off drive shafts and turn the spline by hand until case is neutral then install new shift motor ?
You have to have all four wheels on the ground to do this?
Hello 👋🏾, I have a 08 wk 3.0 that won't go into 4Hi. But will drive in 4Lo I'm hoping this will fix my problem. It just went out all of a sudden on a washboard road.
Does this fix the grinding noise that comes and goes from the transfer case area? I’m not sure if it is the transfer case but I’m hearing a grinding from the rear of my 07 overland, the noise comes and goes
Did you get this figured out? Mines doing the same thing.
Did it fixed. I’m having same problem.
Can a bad Transfer case shift motor puts my car into limp mode? I am getting C140F code "Transfer case range position sensor erratic performance". Randomly I get Transmission Over Temp and the 05 WK 5.7 would go into limo mode (gear# 3). Ive been struggling for 2 weeks to find whats really causing this issue. Thank you
Janek vangonin
And I have one question, when I turn off the ESP, it starts to make noise down there. when I turn ESP back on, the sound disappears. and when I accelerate, the . Hi do you have Transfer case 146 SRT jeep crand cherokee 6.1 4x4 SRT8 2008 WIN : 1J8HCE8368Y105329
Mine won’t go into 4 Low neutral by using the pen as shown. The N light just blinks red for bit and then stops blinking. Any suggestions?
Would it be the same steps for a 2014 grand Cherokee?
+UnknownElementzZ This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
What's the actual trouble code associated in this? Or what is the reason for replacement?
I have a 2005 Grand Cherokee, but it does not have a button to change the drivetrain. How do I do that?
I know you probably won't reply to my comment but how the heck do you get the gear in the correct position to install the new motor? Everytime I try to put it in neutral, the gear is in the wrong position. And at one point I couldn't get my Jeep out of neutral.
+ARC Bonez2520 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Is this an expensive fix?
mine does not go into neutral or low? says "service 4 wd" any help would be appreciated thanks.
Did you resolve ur issue?
I have the same with a Jeep Grand Cherokee Overland 2012
I changed this with out putting the transfer case into neutral? Now it’s out of timing
Why you replace this parts please tell.
I hate how easily you removed the harnest lol. I can't seem to get it off