To everybody that missed the point here: They don't care about the chip. The processor has underfill, wich can result in damage to the pads on the board when removed.Also, overheating the board can cause damage to neighbor components. This cnc process is done to reuse this board in a board swap. They will take the processor, nand, baseband, wifi and some other components from another phone that has a defective motherboard (water damage, broken in half, layer short, etc) and put on this clean one to either restore data or fix the phone.
@@pepe-po4hv it can damage both the components around it and especially the pads on the board that it's soldered to. That would render the board unusable
this cpu is glued back with glue, if removed with a hot torch can lose the lead pins and cannot be restored, this is a good way but almost rarely used because iphone only damaged speakers or screen, board main is almost rarely broken
Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
@@jobyraj007I don't know if your a specialist about that.As far as I know,Isn't the aluminum conduct heat? There's a yellow tape as far as I remember.
many say using a hot air gun is better and doesn't damage the ic but in my opinion, the drilled iphone board is icloud locked, so the cpu, ram, baseband cpu, nand controller are useless, the board is drilled so that no pad is lifted or peeled off The board that has been drilled is used to move the normal iPhone board body which is destroyed, by moving the cpu ram baseband to the drilled board.
All Apple's encrypted data is in the CPU. Because Apple's account cannot be cracked, the owner's mobile phone motherboard is polished off in order to repair the damaged iphone of the motherboard board layer. You only need to transplant the encrypted parts to the CPU, hard disk, baseband, logic chip, baseband chip, and wifi, nfc and other components can work;Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
эх представляю сколько подобных плат ушло в мусор у того кто составлял код для чпу станка, по любому же изначально были неудачи пока не получилось сделать идеальный код для чпу станка.
1. Локальный нагрев - лучший способ запоганить плату. Именно для равномерного нагрева столики и нужны. 2. Нормальный помповый фен тоже ничего не перегревает - перегревает говно с незакрытыми спиралями. 3. Никакой фен не справится с некоторыми компаундами, на которые тут корпус и приклеен :)
Весь ролик автор показывает как долго и упорно спиливает микросхему с помощью ЧПУ. А в конце видимо что то пошло не так и он показывает совершенно новую плату без каких-либо следов.. Браво!! 😁🤔
@@user-js5ly5dl2w вы серьезно? 1) BGA пайку не убрать ЧПУ, греть паяльником и удалять остатки шаров все равно придется. И кстати водить паяльником по холодной плате равно повышенный риск получить вздутие многослойного текстолита. 2) Если ставить на это место новый чип, то все равно придется греть всю плату. Самое главное в этом вопросе - использовать качественное паяльное оборудование и следовать температурным режимам рекомендованным производителями комплектующих. Никакого недопустимого перегрева здесь быть не может. На плате нет электролитических конденсаторов. Более того, чип это не кусок пластика. Куда полетели все те остатки кремния и металлическая стружка? Вы уверены что не под BGA соседних микросхем? На видео показали просто чушь, а вы просто попытались придумать причину почему это не чушь.
All Apple's encrypted data is in the CPU. Because Apple's account cannot be cracked, the owner's mobile phone motherboard is polished off in order to repair the damaged iphone of the motherboard board layer. You only need to transplant the encrypted parts to the CPU, hard disk, baseband, logic chip, baseband chip, and wifi, nfc and other components can work;Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
To everybody that missed the point here:
They don't care about the chip. The processor has underfill, wich can result in damage to the pads on the board when removed.Also, overheating the board can cause damage to neighbor components.
This cnc process is done to reuse this board in a board swap.
They will take the processor, nand, baseband, wifi and some other components from another phone that has a defective motherboard (water damage, broken in half, layer short, etc) and put on this clean one to either restore data or fix the phone.
Thenquil my fryend
thank you for the explanation
cnc can't clean MB as it shown here. So we are missing some episode in here!
Because it’s a blocked board from lost/ stolen device so there is no problem in destroy cpu
Don't buy it. Problem solved.
People seeing machine
Me hearing sound : niiigaa niigaa
Thank God I wasn't the only one 🤣
same
Gger*
Cnc lives matters!
🤣🤣🤣
this is my ringtone now
"way to go son" 👴🏻
I knew I wasn’t the only one💀
Wait what?
@@ayushkaushik8794 it sounds like the drill is saying the hard r 😂
@notcurtisyt
You wanna hear what you wanna hear...racist bastards.😄
Damn i knew id at least find one
That's a great machine 👴
Hot air machine left the chat 😂
Came here to say the same like wth is this
Lol try to desolder the cpu with hot air and come back
@@mokran937 lol this is easier way to do that, if you don’t need to solder it again
They did that to minimize heat you dog
@@DruidMoonkin1 u sure bout that?
Wow🤩😍😍🔥🔥
Когда дал наклеить защитное стекло:
Тот самый сотрудник ДНС:
не, тот самый просто вместо твоего айфона 14 даст древнюю нокию с приклееным на термосорли стеклом для айпада
О чем ты...
@@chronizel1 прислушайся
@@chuvirlaizgrota ну стекла явно не с таким звуком клеят). Хз мож днсные ребята так. Лучше самому
@@chronizel1 если прислушаться то можно услышать "и Ди на хуй"
That's my machine ni- 👴🏻👴🏻👴🏻
Lmao I also heard that
💀💀
What kind of evil company makes a chip that can't be removed with heat... Oh... It's apple
how regular do people even have to replace the bionic chips anyway
You can unsolder these chips with hot air.
heating damages the entire board and the nearby components, it's not an option
@@telecomanda no it doesnt if proffesional who knows what's doing does it.
@@pepe-po4hv it can damage both the components around it and especially the pads on the board that it's soldered to. That would render the board unusable
When it really started chanting MYERHANYEHA, I really felt that.
this cpu is glued back with glue, if removed with a hot torch can lose the lead pins and cannot be restored, this is a good way but almost rarely used because iphone only damaged speakers or screen, board main is almost rarely broken
might be icloud locked
Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
these repair guys are getting highly advanced
A12 is used in iPhone XS. Not 12
looks like an ipad board though
and xr
@@ruslan_kaktus on xr is a11
And XS Max
@@SamsonCanalVechi2 the xr uses the a12
Использовать чпу для отпайки bga это сильно)
Так это не отпайка а спиливание))
@@simurg757 Ну да, та его даже феном сдуть можно а на ик станции это проще простого.
когда обещал заказчику ничего не выпаивать
Ну чисто технически ты ничего не выпаял, просто сразу спилил, и всё
Is this on spotify?
Oh that is freaking cool way better than dealing with soldering!
It's as if billions of transistors cried out in pain all at once, and we're silenced in a few seconds...
The n word progressively gets fast when I heard this
Tech repair is Evolving.. Only Backwards.. You can literally hear The Undertakers Bell in the beginning 💀
Как говорится без шума, без пыли
Var
From nokia days i was working as a technician this is dope like real dope
The People who live before the Hot Air gun was created !!
The board is really ez to damage with hot air and damage neighbor components
@@WonnaCR using aluminium foils will protect the nearest components
@@jobyraj007I don't know if your a specialist about that.As far as I know,Isn't the aluminum conduct heat?
There's a yellow tape as far as I remember.
@@chad5188 kapton tape
@@jobyraj007 pcb bent
Loved the drop
iPhone 12 with A12 chip? Only in Ohio 😅
It‘s an IPhone XS Chip. 😂
POV: *you started bopping to the noise*
Incredible result
RIP Apple Chip 🫠
My new ringtone 😁
😂
Ni- ni-
how love how apple made it literally easier to use a mill to remove their chips than a basic heat gun
Satisfying and clean love it
“Moo gee moo gee moo gee moo gee”
- Rom, brother of Quark
@@ilovecactus111 True lmao
Это новый способ разблокировать айфона если забыл пароль от экрана???
I love this machine, it makes a beautiful melody👨🏻🦲
Man's new
so satisfying 😍
many say using a hot air gun is better and doesn't damage the ic but in my opinion, the drilled iphone board is icloud locked, so the cpu, ram, baseband cpu, nand controller are useless, the board is drilled so that no pad is lifted or peeled off The board that has been drilled is used to move the normal iPhone board body which is destroyed, by moving the cpu ram baseband to the drilled board.
All Apple's encrypted data is in the CPU. Because Apple's account cannot be cracked, the owner's mobile phone motherboard is polished off in order to repair the damaged iphone of the motherboard board layer. You only need to transplant the encrypted parts to the CPU, hard disk, baseband, logic chip, baseband chip, and wifi, nfc and other components can work;Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
yo apple's new track is fire
Beautiful
man's _obliterated_ that entire chipset
эх представляю сколько подобных плат ушло в мусор у того кто составлял код для чпу станка, по любому же изначально были неудачи пока не получилось сделать идеальный код для чпу станка.
Ну да, не на ту глубину врезался, и всё) брак
А что, высота чипа какая-то тайна? Понятно, что станок должен быть идеально откалиброван, а дальше сделает всё чётко по параметрам прошивки
technology came along way, look at that computer precision.
Если прислушаться, можно услышать " не догонишь"
Я там слышу "Нигга"
Ля теперь я тоже это слышу после вашего сообщения... Ах вы такие нехорошие лоли
Кубик - Рубик, кубик- Рубик, кубик- рубик...)))
Я слышу :"нигааа, нигааа"
That takes CPU die lapping to new levels
The amount of.perfect calibration needed for this to work Js insane
Есть фены заточенные под локальный нагрев и ничего лишнего они не перегревают
не фены, а насадки на обычный фен. так или иначе смысл лишний раз греть плату, если есть возможность упростить себе жизнь?
@@Pro_Komp так этот станок не меньше 100 Ки стоит кому она нужна
Уже давно есть инфракрасные паяльники. Греют только там, куда падает свет.
1. Локальный нагрев - лучший способ запоганить плату. Именно для равномерного нагрева столики и нужны.
2. Нормальный помповый фен тоже ничего не перегревает - перегревает говно с незакрытыми спиралями.
3. Никакой фен не справится с некоторыми компаундами, на которые тут корпус и приклеен :)
@@user-zy5jn4es1hчего-то ты мало оценил
A máquina fala" clube 9 "enquanto corta a peça kkk
Pior que fala msm. KKKKK
Весь ролик автор показывает как долго и упорно спиливает микросхему с помощью ЧПУ. А в конце видимо что то пошло не так и он показывает совершенно новую плату без каких-либо следов.. Браво!! 😁🤔
I swear to God I heard R 2 D 2 every time it made a full pass
I was trying to blow the dust away 😂
Kaha pe hai mera 11 ka bhi cpu short hua hai
Your very clever bro...
I'm glad my phones insured
Если прислушаться к звукам , то можно услышать как сверло говорит : 3д принтер
По факту пока не прочитал😂
Вот тебе делать нечего было прислушиваться к звуку станка 😅 истинный инженер
Не сверло, а фреза)
чушь, он говорит - "люди гады"
А отпаять чтоли никак?
Приведет к перегреву.
@@user-js5ly5dl2w ах+енно с Вас 50 к рублей🤣
@@user-js5ly5dl2wа когда паяли - не перегрели?
@@MAKAR_3.14 нет
@@user-js5ly5dl2w вы серьезно?
1) BGA пайку не убрать ЧПУ, греть паяльником и удалять остатки шаров все равно придется. И кстати водить паяльником по холодной плате равно повышенный риск получить вздутие многослойного текстолита.
2) Если ставить на это место новый чип, то все равно придется греть всю плату.
Самое главное в этом вопросе - использовать качественное паяльное оборудование и следовать температурным режимам рекомендованным производителями комплектующих. Никакого недопустимого перегрева здесь быть не может. На плате нет электролитических конденсаторов.
Более того, чип это не кусок пластика. Куда полетели все те остатки кремния и металлическая стружка? Вы уверены что не под BGA соседних микросхем? На видео показали просто чушь, а вы просто попытались придумать причину почему это не чушь.
I think every technician needs this machine
That robot boutta pop his head on the hood
Eu escutei "puta merda" ? kkk
Kkkkkkk
Было бы легче отпилить болгаркой
Я бы посмотрел как ты телефон болгаркой пилишь
Хахахах
@@barsyoutube325 а что, есть есть какие то проблемы распилить?)
@@Yuriy-nik впринципе нет)
Jogatina, jogatina, joga joga, joga joga.
Kiska video hai bhai channel name bata do?
RIP Hot air machine 🤣🤣🤣
good job
I like how the sound started to speed up
Actually A14 is the chip for 12-series. This was used for X series and ipad 8 gen
Good wark❤
Good❤❤
weeee dooood diiiiiii dooood
Good job sir
All Apple's encrypted data is in the CPU. Because Apple's account cannot be cracked, the owner's mobile phone motherboard is polished off in order to repair the damaged iphone of the motherboard board layer. You only need to transplant the encrypted parts to the CPU, hard disk, baseband, logic chip, baseband chip, and wifi, nfc and other components can work;Because nearby components are all sealed and sealed at the factory. The high temperature directly removed will cause virtual welding at the bottom of the components. When reinstalling, low-temperature tin should be used for welding
This board is now going to be used in your refurbished iPhone that will start crashing from kernel panics a week after purchase 😂😂
am I the only one who hears some good percussion in speeding up rhythm ?
Cnc machine sounds like it's going "booga booga"
Waiting for the beat drop 😅
The drill sound like a minion saying move that needle 🤣
Super!!!!!
L i n o d i n o
Запилить обратно слабо?
POV: Your phone was the first to die at your friends sleepover
Very nice Sir 👍
Cinebench R53 on an iphone 12! Awesome scores!
Woah the end sounds like a heart beat.
INCREDIBLY
at the end it Sounds like
" Kulikitaka..taa ka.. kulikitaka..taa.. saka lalalaa... 😂✌
Woww✨✨ this is awesome 👑
Ooookeee dokie
Good working
Very nice
A12 clip is not the CPU on iPhone 12…it’s iPhone XS or XR
Chinese company I used to work with used those same techniques to rip all the chips that I ever sent them ! Reverse engineering was such fun !❤
me filling my roof in minecraft:
Mantap pake CNC mesin
Solder left the group
From expensive technological process to dust in 1 minute
Seems like Machine was speaking a multi umiverse language💀💀
Very cool
Techno music wooow 😆😵
Gimme a piece of sand paper and 10 minutes by hand. 🤣