I'm learning for a hobby. This video offers so much more detail and also professional secrets to get professional results. Thank you for this. In other videos on the topic, they use acetone after removing the old cord for a final cleaning. I wonder if that is unnecessary.
Cleaning the tenon after removing the cork is important but do not use Acetone! It’s fine on wood instruments but will melt most plastic clarinets. Yeah, melt it. That’s not good. Use alcohol on a rag and a bit of determination and elbow grease. Shouldn’t take longer than 30 seconds to do well. Thanks for the compliments.
Thank you. My daughter is in 5th grade and I didn’t want to pay a repair shop to do this small job if I didn’t need to. Question: when you mentioned about putting the cork into one side of the notch, I’m having a hard time seeing on the video. Is it just laying against the raised notch around the clarinet or is it going “into” something I’m not seeing? Thanks!
Save your $$$, you really don't need a 'fancy' tool to remove the old cork. A pair of slip joint pilers at your dollar store will do the same. Just don't force it too hard while going around the tenon.
Very good, except you did not address checking to determine if the cork may be too thick to properly fit into the female tenon. Many times it is too thick and must be sanded down some.
Hi. I wish you had shown (without the silly fast speed) how to remove the bottom two side keys and the link key, and then how to put them back on. This was the whole point of me watching this video. The removal and reassembly of these keys is frightening for most people needing to replace the middle tenon cork. Therefore, I was very disappointed.
That's really good feedback. Sincerely, thank you. I'll do a video on just that topic and let you know when it's up. In the mean time, the best advise I can give is BE BRAVE! Your clarinet is just a machine and the parts come off and go back on with relative ease. The two trill keys are each held on by a rod; unscrew the rod for each (turn counter clockwise) and pull the rod out. Sometimes those rods are difficult to pull out with your fingers so a pair of pliers is helpful. Once the rods are out, the keys will come off with little to no effort. The bridge key (or the A-D ring key) will have a very small screw at the bottom (closest to the center tenon) that needs to be fully removed and a pointed rod going through the F# ring key holding the other side - this rod only needs to be loosened, not taken out, to get the Bridge key off. Hope this helps a bit. Let me know if you have other questions and again, thanks for the feedback.
Contact cement is why you need. Get it at Ace Hardware, put it on thin, put it on both the cork and the clarinet, let it sit for at least 5 min and then press it on. Where it makes contact is where it will stay so line it up right.
I'm learning for a hobby. This video offers so much more detail and also professional secrets to get professional results. Thank you for this. In other videos on the topic, they use acetone after removing the old cord for a final cleaning. I wonder if that is unnecessary.
Cleaning the tenon after removing the cork is important but do not use Acetone! It’s fine on wood instruments but will melt most plastic clarinets. Yeah, melt it. That’s not good.
Use alcohol on a rag and a bit of determination and elbow grease. Shouldn’t take longer than 30 seconds to do well.
Thanks for the compliments.
@@repairmasterclass Good to know, for sure. Thank you.
Nicely explained.
Thank you. My daughter is in 5th grade and I didn’t want to pay a repair shop to do this small job if I didn’t need to. Question: when you mentioned about putting the cork into one side of the notch, I’m having a hard time seeing on the video. Is it just laying against the raised notch around the clarinet or is it going “into” something I’m not seeing? Thanks!
@@88keysLA Good question, it’s just laying up against the notch.
Well done. Thanks.
This was an amazing tutorial, what cork seal did you use?
@@moonwhatever21 Contact cement to hold the cork on, paraffin wax to seal the cork then Tech-Grease as a slippery lubricant to finish it off.
Thank you.
Where can one find that cork scraper in US?
www.ferreestoolsinc.com/products/f12-cork-stripper among other places.
Save your $$$, you really don't need a 'fancy' tool to remove the old cork. A pair of slip joint pilers at your dollar store will do the same. Just don't force it too hard while going around the tenon.
@ True, if they fit. On most instruments they do, but there are several where pliers are too wide and will damage your instrument.
@ Hopefully common sense will prevail...
Looks like you built a nice holder for small hardware using a piece of finger board from something. :cool:
:) Yup. I like reusing instrument parts and this violin fingerboard was available when I needed a new rod block. Good eye.
What glue do you use?
Contact cement is what you should use. Apply it to the cork and tenon, then wait 5-15 minutes for it to get tacky, then touch them together.
Very good, except you did not address checking to determine if the cork may be too thick to properly fit into the female tenon. Many times it is too thick and must be sanded down some.
Yep, but that will be assessed at the time of putting the two together.
Hi. I wish you had shown (without the silly fast speed) how to remove the bottom two side keys and the link key, and then how to put them back on. This was the whole point of me watching this video. The removal and reassembly of these keys is frightening for most people needing to replace the middle tenon cork. Therefore, I was very disappointed.
That's really good feedback. Sincerely, thank you. I'll do a video on just that topic and let you know when it's up.
In the mean time, the best advise I can give is BE BRAVE! Your clarinet is just a machine and the parts come off and go back on with relative ease. The two trill keys are each held on by a rod; unscrew the rod for each (turn counter clockwise) and pull the rod out. Sometimes those rods are difficult to pull out with your fingers so a pair of pliers is helpful. Once the rods are out, the keys will come off with little to no effort. The bridge key (or the A-D ring key) will have a very small screw at the bottom (closest to the center tenon) that needs to be fully removed and a pointed rod going through the F# ring key holding the other side - this rod only needs to be loosened, not taken out, to get the Bridge key off.
Hope this helps a bit. Let me know if you have other questions and again, thanks for the feedback.
What glue do you use??
Contact cement is why you need. Get it at Ace Hardware, put it on thin, put it on both the cork and the clarinet, let it sit for at least 5 min and then press it on. Where it makes contact is where it will stay so line it up right.