Thanks alot. The little plug with red and orange wires was always disconnected when i had my android radio connected straight to the car. Now i have a T harness to connect an external amplifier and the radio wouldnt startup with the new T harness in between.
Thank you, this helped me troubleshoot a problem on a similar amazon 9 in android radio where the only speaker/tweaker that was working was the central one next to the windshield , once I wired the Amp and Amp-Con wires and I enabled the amplifier option on the infotainment all speakers are working. Although I'm still waiting for the high to low impedance harness adapter to arrive from Aliexpress to have full volume / amplifier capacity.
Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, LOL… bro you’re the best thank you soooo much.. it’s been over a year with no rear speakers or sub..
Do you know if I'll be able to retain the factory/oem microphone on my car to use it with the CC3? The stereo I'm replacing is the RNS-e (Audi Navigation Plus) head unit.
Hmmm, I am not sure, but do you know if the RNS-e has a separate cable for the microphone? As for the mic to work with the CC3 you need to insert the mic with 3.5mm jack into the additional harness on the back fo the unit. If you dont have that cable you wont be able to use the original mic.
Hey! Ik heb recentelijk de BSN 5.0 autoradio van mijn Audi A3 8P vervangen voor een aftermarket radio met CarPlay etc. Met een extra verloopstekker werken nu alle speakers. Ik heb geen bose maar het Audi audiosysteem bestaande uit 5 speakers voor 2 achter en subwoofer links achterin kofferbakschot. Nu heb ik sterk het idee dat ik er qua geluid/bass op achteruit ben gegaan. Vooral op laag volume mis ik echt bass. Zou het kunnen dat ik ook de adapter nodig heb die je op 1:03 laat zien? Of zou het een andere oorzaak kunnen hebben dat ik nu minder goed geluid/bass heb? Ter info: nieuwe radio output is 4x 80W. Ik hoor graag!
Hoi Stefan, ja het zou echt kunnen dat je die adapter nodig hebt want als je een non bose systeem hebt is de kans echt heel klein dat dat systeem de subwoofers in de 8P aan kan zetten. Dan mis je dus letterlijk al je bas. Voordat ik het harnas kocht en installeerde had ik dat. het enige waarop het kan lijken is dat je voor speakers de bas een beetje door laten komen maar meer niet. Ik zou echt het harnas kopen en proberen. ook een grote tip, pas je equalizer aan. De CC3 met standaard settings was echt slecht maar na het aanpassen van de curve is het echt veel beter dan standaard. Laat even weten of het lukt!
If your audi a3 has got rear amplified speakers then just get the 49 AUD 02 harness and this will work 100% If you've got fully amplified speakers then get the 49 AUD 02 BOSE ALL THE BEST
To my understanding, I don't know how yours is wired but, do you need to lower the impedance coming from the radio to the amp? I just bought a hilow adapter.
Basically yes, but you do that by just wiring up the harness and making sure the adjustment screws in the transparent casings of the harness are set correctly. Correct here means you turn on the unit and play sound and adjust the screws so you hear everything well. Do this on both transparent cases.
Yes and then it does not work. Only front speakers work. I installed it without first and then worked with TEYES to solve the issue which resulted in the harness being added.
Shot in the dark but im unistalling an old aftermarket headunit that the previus owner put in. I got the original back in thinking it would fix the lack of rear speakers and sub but it didnt. Any idea what I should to trouble shoot? Any advice would be huge
Pfoee so with the originals there is no back speaker sound? Maybe a wire break or was cut when the aftermarket ones were fitted? Otherwise see if you can manually power the amp with external power is the only thing I can think of!
Hello, I do not believe I have that. But that is because the car is from 2008 so its lacking many newer features. I do think you might need the OBD tool by teyes for that.
Hi there. I have a question for you? This is for a 2014 Audi Q5 actually. Does your unit have an AUX app installed in it and does it allow you to access OEM display information through it? Mine is a CC3 2K unit and it has an AUX app in it. The problem is that when I open the app it shows 'NO VIDEO SIGNAL'. I guess the app is to show OEM Display information like Settings, Oil level etc. Thank you.
Oee my unit does not have an Aux app that I know of. I also dont know if that is the app that will give you original vehicle information. Did you connect all the wires? Is there maybe one unplugged?
Any idea if this is needed for the TT mk2? It's a 9 channel system with a 5 channel amp with 4 line inputs (non Bose). Will the teyes RCA pre outs be okay or do I have to get this adapter to give me a higher voltage signal?
I believe that you will need the harness. If I look at the list of half amplified Audi`s, the TT between 2006 to 2014 with quadlock connector is on it. I would say try with and if anything you can easily return the harness.
@@snipermakedonski I believe the TT is fully amplified. But it is non Bose. I'm not sure if the cc3 can provide the correct impedance and voltage from the preouts without the adapter. But yes thankfully it is on Amazon UK, so I can get it and see if I need it.
This is very informative! Did you have any issues with the OEM panel (front fascia mount)? They sent me on labeled 2002-2008, I have a 2011 and it doesn't seem to fit. I'm afraid that if it ever did go in, it would never come out without breaking it.
Glad to hear! yes I also had that issue. let me link you to my forum post on XDA. The frame is VERY VERY tight. actuall the tabs are molded to wide so you need to push the tabs in. Big tip do NOT screw the unit into the frame. Otherwise getting it out probably will be impossible. forum.xda-developers.com/t/teyes-cc3.4189041/page-142#post-88059829
It might be that the reverse is automatically triggered by the CANBUS itsself. If you hook it up and shift into reverse does it turn on? And if not you need to wire the trigger wire to the reverse light IIRC.
Please could you show how the 4 audio red and white cables are plugged In please? I have bought the low impedance adapter but now not sure which cables plug on where !
Which cables do you mean? The red and white ones? Match the colors and lables, so Left in goes into left out and its male to female connectors so you just make sure its all 1 long harness no loops.
Hello, today I installed multimedia in my Audi A3, however, the rear speakers are almost inaudible, as well as the woofer. Does that part for the amplifier already exist in the cables or does it have to be bought additionally? Of course, I made an appointment to have the connection checked again, because today I didn't manage to return the car to the service because I found out about the problem too late.
Its very simple. You match the in and out cables with the tags on them. Cant go wrong. It phisically wont fit into a wrong cable if its the same color. Link to the cable: teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt
In audi with bose system the sound only work when you put the two blue cables together. And now I have one problem with static noise and I dont know how to remove
@@snipermakedonski btw i dont seem to have the amp wire? I only have the amp control wire, but theres is a blue wire that is capped off but the lable says auto ant?
@@sevkoiseric Hmm I have heard this before. Just see if there is a similar wire that runs to the right pin on the main loom. if not ask teyes support via an email as it seems they changed something. Auto ant is what you need to hook up to your radio antenna. What I describe in the video as double plug you need to check.
Thanks for this. I posted on xda forum thread you linked but have not had any response. I bought the 2k version for my a3 (with bose) but I have the following issues: 1. Hiss noise with high/low pass converter fitted 2. All speakers work but sub will not power on 3. Steering wheel controls do not work. Please could you advise how I could resolve these issues? Many Thanks
Hi! Sorry I have not vivisted that forum in a bit and for some reason did not get notitifications. The hissing, try turning the screws on the impedance harness. thing is though I am not sure you need that harness with Bose. I sadly dont have it so dont know but others say it might not even be needed. Sub might need to be turned on in the audi menu settings in the unit. Check if the amp is turned on there. Sadly for steering wheel controls I dont know as I dont have them but did you enable the CANBUS properly and learn them in the system? You need to teach the unit what it should do with the button presses.
I have the bose system and made all the connections you made. I still don't have sound out any speaker. I don't have the low to high amp boxes you have though. That comes as an extra special harness from Teyes. Do I need that? Its an added cost of 40 USD.
Hey there, nice video. I bought an Ali express head unit (GATAXASKY) and it has a pink wire that says external amp control that is capped off. I’m pretty sure it does the same thing as the one you have. My question is I have one blue wire that goes from my Xtrons adapter into another harness for the radio. The radio calls the blue wire the Auto antenna wire, do you know if this is the one I should connect the pink wire to, and if if so do I tap into the wire, or cut it and just have it go to the pink one?
Hi, no the auto antenna wire is a different one. that should connect to your radio antenna cable (also blue one). You need to find a different wire and I would sai if you need to connect one. Cut into the sheathing, squish the cable together a bit so the internal wire come apart a bit and thread the new wire through those gaps. Then twist. Plus electrical tape or even better, solder. Should work best.
Hello brother i cant find the amp cable thats running from the harness, I know my harness should have the cable but it doesn't, the amp control cable is as you mentioned, but de amp cable from the harness isnt ,hope you could help me telling me in which pin does the amp cable is
Hmm I have heard this before. Can you check the main wiring harness and see if there is a cable that is the same color as the amp cable? Or in the wiring diagram they give you what pin should have the amo cable go to it and trace it back?
Oeee, I would honestly not be sure. If there are no wires at all I think you should be fine then. Try and install it and use the fader in the audio settings to move the sound around. If certain speakers dont work (due to missing wires for example) you should really notice it there.
I finally got rid of my garbage Soarcomer head unit (that was not compatible with wired Apple CarPlay and could never reconnect wirelessly without a complete power cycle / cold start) and bought a T'EYES CC3 2K instead. It seems much more well made. So I have a look at your video again before installing it. You say at 2:05 to disconnect the red ACC wire from the ISO connector (that goes nowhere indeed as the ISO connector is not used) and connect it instead to the red ACC wire coming from the main 16-pin power connector of the head unit (the 'G' block). That makes sense. However, where does the ACC current flow from? There is absolutely no other remote ACC wire available on the harness to connect to the remote ACC wire that runs in the dash from the fuse box, and there is no ACC power cable in the Audi Quadlock used, only the BAT (constant voltage) one there. In this configuration, I don't even understand how your head unit can boot! EDIT: Wow, I connected as you said and… it works! 😶 And I really don't know why, as the independent ACC wire coming from the fuse box is not used. Maybe the unit actually boots with a digital signal from the CANbus, then provides +12VDC on its ACC wire from BAT? Anyway, the unit is gorgeous, much snappier and responsive than the crappy previous one :)
Good to hear! The ACC IIRC comes from another main wire in the original quadlock. Its illogical but that is why it took me 3 days to figure it out and I thought the unit was broken!
@@snipermakedonski Good to know! For the previous Android HU I briefly had, it didn't work before I run a dedicated ACC wire myself from the fuse box. I was really surprised when the CC3 powered on without actually connecting that additional wire! Thank you for your video, it helped me a lot 👍
There should be red and white in and out. Connect the corresponding colors of in and out to eachother. I am not sure on the amp wire TBH. Are you sure there is no second AMP wire? Otherwise ask Teyes Support, they are very helpful.
Hello brother, my back speakers and the subwoofer don’t work, to make them work I have to buy the 1v to 4v adapter no? Which are the conexions that I have to make
Yes you need to buy the harness to make them work. its the exact same issue I had. its this one: teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt
Hi. I bought the lux one for audi a4, and after i connect the quad lock, the buttons near the shifter will not work anymore. The order was right for my model, but i dont know if i received the correct cables. The air conditioning cables dont fit also. Any sugestions ? I see you have a canbus box on cc3, none of this on the one lux model
@@snipermakedonski i did a reasearch, and i found that the shop wich i paid to mount my navigation, had no clue what the cables were for. There is a bypass on the canbus also, but they told me that cable dont fit in the airconditioning module, and i got the wrong cable 😃
I bought an android stereo it came with the impedance adapter, without it only the front speakers sound. my question is: where the 4 impedance adapter wires are connected?
Once the head unit is installed, how do you remove it? It clips in with four plastic clips. Do you just pry it out? I need to order the antenna adapter.
Its very hard, you need to use plastic pry tools, however. I reccommend just not screwing the unit to the frame. Then you can just put a nail around the side of the glass and pull up. Or with a suction cup.
Hi mate, sorry for the late response, this is it, just check if the website is the right one for you in terms of location: teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt?shpxid=056495a5-8c7d-4be3-9bae-ea69a616de97
Hi there, I am looking for some advise really. I have purchased an xtrons IA series unit for my 2006 Audi A4 with quad lock. They sent the unit with a BOSE adaptor, which I used as I have Bose system. I got allot of static problems when the lights were on and rustling noise constantly. I contacted Xtrons and they sent me a high to Low impedance adapters free of charge. When I tried to use it one of the rear female phono ports was faulty and only a faint sound coming out when I turned the volume right up. I then purchased a 2nd hand adaptor and that worked fine for about two weeks but has since stopped working with the exact same problem. Can you advise what might be causing the issue? Thank you in advance for your help.
Hmm not 100% sure. Might be fluctuating voltage. You might need a filter. Here is a link on the Teyes website but you can find them more online: teyes.eu/products/teyes-power-filter Also dont turn it up all the way, keep it in the middle, too much is bad. Try the sound settings and see if there is a power mode in the settings to boost the loudness. Teyes has that in the software. Let me know if it works!
@@snipermakedonski yeah I basically need that but for quadlock. I am using the xtrons one but it’s cheap looking and convinced they are faulty. Can send pics if you want.
@@jasonpoulton865 I would order the one from Teyes then as they also suggest that one I linked for quadlock. I would send their customer service a message with the question on how to install it just in case. They helped me a lot.
I am confused about the adapter and Bose systems. Some say if you have Bose you need the adapter while others say you dont. Witch one is it?? Many thanks
I personally did not know but see this comments: @HARRYMWAI If your audi a3 has got rear amplified speakers then just get the 49 AUD 02 harness and this will work 100% If you've got fully amplified speakers then get the 49 AUD 02 BOSE
It was the 2 amp remote wires that got me. Spent half a day messing about with the ground on my amp. Since when do they have 2 amp wires 😂 thanks again
Mate will this wiring work on audi tt mrk 2 I've had a nightmare of time. Your video is very helpfull cheers mate keep up the good work I've not got amp wire connect and the sound is very muffled hope joining the amp wire will sort it out
Glad to hear the video helped! What modelyear is your TT? And do you have the same connectors? If so then it should. Also, if the amp is working but muffled it might be the 2 screws in the impedance harness, try turning those. You are non bose right?
@snipermakedonski hi mate it 2013 plate mrk 2 audi tt I have only the 1 amp wire not the 2 as you have should the amp wire be connected to 12 volt am just waiting on the lead to arrive thanks non bose
@@MrJoelcc9 Interesting. Strange that there is only 1 wire. And there is no second blue and white or blue cable with a cap on it? At all? Then it maaybe should be connected to the 12V but be carefull, if the arm is powered all hte time it might drain the battery.
Please can you help ive fitted the unit into my audi a4 and have no sound from front right or rear + no amp wire from iso, amp control wire from the back off the unit is black not blue and white
These 2 AUX cables coming from the harness (in L and in R) Do I plug them into the other AUX cables or the RCA? Because I tried both options and I still have no sound.. Thanks 🙌
IIRC it should be the aux cables. aka the reverse (female leads) of the main harness. The RCA cables are for an aftermarket system I believe as they also have a separate bass control. If you dont have sound, check the settings on the screps in the additional harness if they are set wrong they will also give 0 sound.
hey very nice video ! I have trouble with my steering wheel buttons... do you have info ? I saw in some forums that i have to connect "key1" wire with ground and "key2" with another wire... please help me :)
Ahh I sadly dont have steering wheel buttons but IIR there should be a set of wires that connects to key 1 and 2 indeed OR it should be CANBUS driven. Did you set up the canbus profile correctly in the settings on the unit? It could be that that is what is missing and then you need to program the buttons. Otherwise you need to look up wiring diagrams for the car and find the 2 cables on the harness that are for the steering wheel buttons and hook those up to key 1 and 2.
try this man, connect wifi, go to settings, factory and then type the password which probably is “8888”, go to “car model” or something like that, press “LZ” then “Audi” then “A3” and finally “04~12”, confirm. The steering wheel controls should work after it. peace!
Yes but make sure yo have the antenna plugged in and routed to ABOVE your dash. Otherwise it wont work. It needs clear sight through the glass. Which settings do you mean?
@@snipermakedonski hm, sadly mine doesn't catch up nothing, even i routed it outside from dash hmmm.. settings i meant about " can bus settings " it show the lists, i try to choose mine car settings and after little of loading it says failed
@@ComedyBow Hmm for the CANBUS, did you select the correct box? The one you got supplied? IIRC mine was a binary one. For the GPS, try rebooting by dragging down from the top. I had that exact issue and a reboot fixed it. Its different from turning it off.
@@ComedyBow Hmm you should have a CANBUS box, check the manual. It might have already been connected but if not there is your problem. I would also check if that is the right one selected or not.
Hmm, did you turn the little knobs on the impedance harness? The transparten ones in the middle harness? Try turning on music and turning those actively. Also see if your amplifier is on in the settings
Hi bro, i bought the harness and installed it back speakers do work but still my multimedia doesnt recognize the amp and the sound is not even close to the factory one. Any tips and tricks?
How do you mean does not recognize? Did you turn on the amp in the sound settings in the software? Otherwise turn on loud mode in the equalizer and or power sound in the normal sound settings. Let me know if it works!
In settings i have setting for music when i enter those settings in the top left corner it says unknown amplifier and when i try to change bass, fader etc nothing happens. Yes i have turned on amp in settings. I have tried loudness on off but no luck.
Hello, please help! I've been having so many issues ever since I installed my Cc3 into my 16 Hyundai Veloster Turbo that if I told you, you would be like OMG! 😮 But I came out of it. And I did what you said about blue wires for the amp, and now I get no sound coming from my speakers. I'm not sure what to do know. Before, I did get some sound from the front, but now nothing after splicing the blue wires. I would appreciate any suggestions. Thank you
Hi! I understand the frustration. I had the same. So in the settings menu for audio, did you turn on the amp with the toggle? Also have you tried raising the power level in the settings?
@@snipermakedonski Hello, sorry for my delay in responding. Omg it seems like I fix one problem and the next day a new one will pop-up! So, I fixed the no sound problem. But now I'm not sure if the factory Amp is working because. When I switch off the amp in the teyes equalizer app I hear no difference in sound volume. Also do I need to connect the Key1 and key2 wires? And I get no (vehicle information) in the vehicle information app. I can't go to Teyes support because I didn't purchase my head unit directly from them. Thanks for your quick response and I would appreciate any suggestions you can provide. Thanks
@@lou.242 Ahh ok. If you have a car with multifucntion buttons on the steeringwheel (basically any buttons at all), then you need to connect the key 1 or 2 (depending on the wires coming from your car wiring loom included in the box) wires. If you dont get any vehicle information in the app, you need to probably set the right canbus settings. Look in the teyes app for instructions or online. I know for my car I got a (I think) brown canbus box which was binary and then in the settings I selected that, box, then audi a3 etc. and that should help. Otherwise you probably need the OBD dongle. Hope it works!
Thanks for this Video, I have put in a few days in the installation now, and I stucked with no sound...Audi TT MK2 from 2014 - I have perfect image, the Steering wheel controls works fine, but no sound, did order the addional adapter cable with the "Special Power Adapter Cable with Audio Amplifier Cable for Audi A3/A4/TT" I Do not have the Bose version of speakers, and have the "OEM Audi TT Trunk Amplifier 8j0-035-223-f" Please support me with how to solve the sound issue. If i connect the OEM stereo from Audi the sounds is perfect, so no issues with the cables etc in the car. Thank you.
@@snipermakedonski thanks for reply, No, all was good, and I have been at 2 different "Car stereo" shops, And they have not been able to fix it. If i turn upp the volume to high, the fan on the back start spinning, but maybe that a factory setting?, This is so strange, i have checked maybe 100 different videos on this topic,
my friend got the same one, I installed it but the rear speakers don't play. and what worries me the most is that I don't know how to unclip it. Can someone help?
Unclip the frame? Its really tight. You need trik removal tools. Rear speakers is you are missing the middle harness. The low to high impedance. Teyes sells one
@@snipermakedonski yea I have the harness I don’t know where to contact the harness I know that I can connect red and white amp to it but I don’t know where to connect the other side of it
@@02any1 That is why the rear sperakers are not working. Connect one end to the main harness coming from the car and the other end into the main harness of the headunit. Look in the video to see. Also look on the Teyes sale website for the unit. It has a wiring harness.
Hi .very nice and good information. I don't have a Audi but a Citroen C5 x7 . I have the same problem .no sound back and my subwoofer is not working properly. How can come in touch with you ? Regards Tibor
@@A38P Hmm strange. And teyes not knowing? what phone do you have? Did you also check settings in the options menu? Maybe there is a switch you need to change?
@@snipermakedonski s21 tried it with iphone and an oppo I can't see anything to change it from showing the number, rather than the contact name. Open car play shows the name, strange
Hello friend, sorry because I don't know English and it doesn't translate what I want, I ask you how to remove the radio because I have the same Audi A3 car and the same new radio to install and I understand that if the plastic casing is mounted and you screw it to the plastic and you mount it definitively to the car it does not come out anymore since there is no way to remove the casing it does not have any slot, that is what I ask you how do you remove it friend
Ahhh I understand now. No problem! So yes if you screw it into the plastic frame and then put it in (after connecting the cables), it will click in (it will be VERY difficult to get in) and getting it out will be alsmost not possible. That is why I advise not screwing it onto there. removing it, screwed in or not requires plastic trim removal tools like this: www.amazon.nl/Tresalto-verwijderen-deurpanelen-bevestigingsmiddelen-dashboards/dp/B01L8GHB7O You get it behind one of the edges of the plastic and gently try to get it out.
Hello friend, greetings from Spain, I have a problem with my radio, I have a problem that the touch does not work just like that, let me explain, you touch the screen and it does not respond if I turn off the car and start it, that's how it works but it does it every time but it's very strange, as I explained, the radio works but you touch the screen and you can't do anything or put voice on, remove or anything, it's very strange, does that happen to you too? Thank you and greetings from Spain
@@nitro_power audis without bose still have factory amplifier for rear speakers which do need the high to low adapters (or adjust the settings in fader app)
@snipermakedonski I have an android head unit I installed Everything I got a ISO connector to 16pin connector for the headunit, and the rear speakers are not working. I have a 2005 audi a3 non bose
Sadly I dont speak fuelt enough french to do that but you can auto translate my post on the XDA forums! forum.xda-developers.com/t/teyes-australia.4240385/page-26#post-88059851
Hello, what do you mean exactly? I setup my canbus and all seems to work. I do not however have a multifucntion steeringwheel so did not need to programme things.
Thanks, back speakers now work, was the two blue amp wires i never knew about
Glad to hear!
Thank you very much, good man! You saved me a couple of days of my life! Bless you!
Glad to hear!!
Thanks alot. The little plug with red and orange wires was always disconnected when i had my android radio connected straight to the car. Now i have a T harness to connect an external amplifier and the radio wouldnt startup with the new T harness in between.
Thank you, this helped me troubleshoot a problem on a similar amazon 9 in android radio where the only speaker/tweaker that was working was the central one next to the windshield , once I wired the Amp and Amp-Con wires and I enabled the amplifier option on the infotainment all speakers are working. Although I'm still waiting for the high to low impedance harness adapter to arrive from Aliexpress to have full volume / amplifier capacity.
Glad to hear I could help even with a different unit!
Can you send the link to buy that adapter pls?
@@erismoqi Here you go: www.teyes.com.au/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt
you have saved me!!! THANKS 🙏
Thank you, Thank you, Thank you, Thank you, Thank you, Thank you, LOL… bro you’re the best thank you soooo much.. it’s been over a year with no rear speakers or sub..
hahaha very glad to help!
Hello,
where did you get the canbus box, was it included in the scope of delivery?
Thank you soooo much!!!
Do you know if I'll be able to retain the factory/oem microphone on my car to use it with the CC3? The stereo I'm replacing is the RNS-e (Audi Navigation Plus) head unit.
Hmmm, I am not sure, but do you know if the RNS-e has a separate cable for the microphone? As for the mic to work with the CC3 you need to insert the mic with 3.5mm jack into the additional harness on the back fo the unit. If you dont have that cable you wont be able to use the original mic.
Hey! Ik heb recentelijk de BSN 5.0 autoradio van mijn Audi A3 8P vervangen voor een aftermarket radio met CarPlay etc. Met een extra verloopstekker werken nu alle speakers. Ik heb geen bose maar het Audi audiosysteem bestaande uit 5 speakers voor 2 achter en subwoofer links achterin kofferbakschot. Nu heb ik sterk het idee dat ik er qua geluid/bass op achteruit ben gegaan. Vooral op laag volume mis ik echt bass. Zou het kunnen dat ik ook de adapter nodig heb die je op 1:03 laat zien? Of zou het een andere oorzaak kunnen hebben dat ik nu minder goed geluid/bass heb? Ter info: nieuwe radio output is 4x 80W. Ik hoor graag!
Hoi Stefan, ja het zou echt kunnen dat je die adapter nodig hebt want als je een non bose systeem hebt is de kans echt heel klein dat dat systeem de subwoofers in de 8P aan kan zetten. Dan mis je dus letterlijk al je bas. Voordat ik het harnas kocht en installeerde had ik dat. het enige waarop het kan lijken is dat je voor speakers de bas een beetje door laten komen maar meer niet. Ik zou echt het harnas kopen en proberen. ook een grote tip, pas je equalizer aan. De CC3 met standaard settings was echt slecht maar na het aanpassen van de curve is het echt veel beter dan standaard. Laat even weten of het lukt!
my audi's rear speakers are also not working. I checked the wiring and there is no AMP cable, only AMP-C.
Hmm is there a blue wire on the main harness that looks like the amp cable? Otherwise you might need to tap into that.
If your audi a3 has got rear amplified speakers then just get the 49 AUD 02 harness and this will work 100%
If you've got fully amplified speakers then get the 49 AUD 02 BOSE
ALL THE BEST
Could you put a purchase link or an image of the product 49 Aud 02 Harness?
Thank you this helped me boot the radio ! Did you end up having the steering control working ? I cannot make them work or program them
I dont have steering control but if I understand correctly, based on forums, you need to hook up the key 1 and 2 connectors to the canbus in some way.
To my understanding, I don't know how yours is wired but, do you need to lower the impedance coming from the radio to the amp? I just bought a hilow adapter.
Basically yes, but you do that by just wiring up the harness and making sure the adjustment screws in the transparent casings of the harness are set correctly. Correct here means you turn on the unit and play sound and adjust the screws so you hear everything well. Do this on both transparent cases.
Hi there, did you try installing this unit without the high-low converter? I thought that component was only for A3's with BOSE.
Yes and then it does not work. Only front speakers work. I installed it without first and then worked with TEYES to solve the issue which resulted in the harness being added.
Shot in the dark but im unistalling an old aftermarket headunit that the previus owner put in. I got the original back in thinking it would fix the lack of rear speakers and sub but it didnt. Any idea what I should to trouble shoot? Any advice would be huge
Pfoee so with the originals there is no back speaker sound? Maybe a wire break or was cut when the aftermarket ones were fitted? Otherwise see if you can manually power the amp with external power is the only thing I can think of!
Hello,I just wanted to know if you have among the applications displayed an icon information on the vehicle
Hello, I do not believe I have that. But that is because the car is from 2008 so its lacking many newer features. I do think you might need the OBD tool by teyes for that.
Hi there. I have a question for you? This is for a 2014 Audi Q5 actually. Does your unit have an AUX app installed in it and does it allow you to access OEM display information through it? Mine is a CC3 2K unit and it has an AUX app in it. The problem is that when I open the app it shows 'NO VIDEO SIGNAL'. I guess the app is to show OEM Display information like Settings, Oil level etc. Thank you.
Oee my unit does not have an Aux app that I know of. I also dont know if that is the app that will give you original vehicle information. Did you connect all the wires? Is there maybe one unplugged?
Any idea if this is needed for the TT mk2? It's a 9 channel system with a 5 channel amp with 4 line inputs (non Bose). Will the teyes RCA pre outs be okay or do I have to get this adapter to give me a higher voltage signal?
I believe that you will need the harness. If I look at the list of half amplified Audi`s, the TT between 2006 to 2014 with quadlock connector is on it. I would say try with and if anything you can easily return the harness.
@@snipermakedonski I believe the TT is fully amplified. But it is non Bose. I'm not sure if the cc3 can provide the correct impedance and voltage from the preouts without the adapter. But yes thankfully it is on Amazon UK, so I can get it and see if I need it.
Hi, i need help with cc3 2k , no power, or if yes, after takimg keys out the head unit screen still on 😢😢 (vw CC 2015)
This is very informative! Did you have any issues with the OEM panel (front fascia mount)? They sent me on labeled 2002-2008, I have a 2011 and it doesn't seem to fit. I'm afraid that if it ever did go in, it would never come out without breaking it.
Glad to hear! yes I also had that issue. let me link you to my forum post on XDA. The frame is VERY VERY tight. actuall the tabs are molded to wide so you need to push the tabs in. Big tip do NOT screw the unit into the frame. Otherwise getting it out probably will be impossible.
forum.xda-developers.com/t/teyes-cc3.4189041/page-142#post-88059829
@@snipermakedonski thanks for all the info. Just ordered the harness for the rear speakers. 🙏
@@snipermakedonski I got the harness! Does it just go between the car and the original harness?
@@drmfree yes, so ISo from the car --> harness --> Teyes CC3 harness
@@snipermakedonski hello I found a frame that fits better on eBay from auto-trimtray in case you need one.
I have basically the same thing how do I wore the back up camera? There is no reverse trigger wire to tap into using the cam bus??
It might be that the reverse is automatically triggered by the CANBUS itsself. If you hook it up and shift into reverse does it turn on?
And if not you need to wire the trigger wire to the reverse light IIRC.
Please could you show how the 4 audio red and white cables are plugged In please? I have bought the low impedance adapter but now not sure which cables plug on where !
Which cables do you mean? The red and white ones? Match the colors and lables, so Left in goes into left out and its male to female connectors so you just make sure its all 1 long harness no loops.
Hello, today I installed multimedia in my Audi A3, however, the rear speakers are almost inaudible, as well as the woofer. Does that part for the amplifier already exist in the cables or does it have to be bought additionally? Of course, I made an appointment to have the connection checked again, because today I didn't manage to return the car to the service because I found out about the problem too late.
The high to low impedance adapter harness already exists and you can get it on the Teyes website.
Does the impedance konverter K28 at 1:04 have any wiring diagram? Where did you connect the wires?
Its very simple. You match the in and out cables with the tags on them. Cant go wrong. It phisically wont fit into a wrong cable if its the same color.
Link to the cable: teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt
Thanks. I just thought you mean that it was a separate converter
In audi with bose system the sound only work when you put the two blue cables together. And now I have one problem with static noise and I dont know how to remove
Me too I have only noise not music or anything. Bose system
great video!
Question
-does it work just by connecting the amp wires or is the converter necessary?
If you have the non Bose system you need the converter for the rear speakers and amp to work. otherwise it wont at all.
@@snipermakedonski btw i dont seem to have the amp wire? I only have the amp control wire, but theres is a blue wire that is capped off but the lable says auto ant?
@@sevkoiseric Hmm I have heard this before. Just see if there is a similar wire that runs to the right pin on the main loom. if not ask teyes support via an email as it seems they changed something. Auto ant is what you need to hook up to your radio antenna. What I describe in the video as double plug you need to check.
Thanks for this. I posted on xda forum thread you linked but have not had any response. I bought the 2k version for my a3 (with bose) but I have the following issues:
1. Hiss noise with high/low pass converter fitted
2. All speakers work but sub will not power on
3. Steering wheel controls do not work.
Please could you advise how I could resolve these issues? Many Thanks
Hi! Sorry I have not vivisted that forum in a bit and for some reason did not get notitifications. The hissing, try turning the screws on the impedance harness. thing is though I am not sure you need that harness with Bose. I sadly dont have it so dont know but others say it might not even be needed. Sub might need to be turned on in the audi menu settings in the unit. Check if the amp is turned on there.
Sadly for steering wheel controls I dont know as I dont have them but did you enable the CANBUS properly and learn them in the system? You need to teach the unit what it should do with the button presses.
I thought the extra parts were for only if you do have BOSE and not for non-BOSE?@@snipermakedonski
No the extra part is for non BOSE. I dont know how to install with BOSE systems.@@scottburgess2263
I have whining noise using the CC2+ in my Audi A3, using bose speakers...any ideea what to do?
Yea you need a power filter probably. Look on the Teyes website and seach Power Filter.
I have the bose system and made all the connections you made. I still don't have sound out any speaker. I don't have the low to high amp boxes you have though. That comes as an extra special harness from Teyes. Do I need that? Its an added cost of 40 USD.
Hi, I am not sure tbh but I think you should not need them AFAIK. Maybe message Teyes support? I have a non bose so sadly cant help you there?
In the options of your headunit you must have one option that says something like : amp -> OFF . try put On
Hey there, nice video. I bought an Ali express head unit (GATAXASKY) and it has a pink wire that says external amp control that is capped off. I’m pretty sure it does the same thing as the one you have. My question is I have one blue wire that goes from my Xtrons adapter into another harness for the radio. The radio calls the blue wire the Auto antenna wire, do you know if this is the one I should connect the pink wire to, and if if so do I tap into the wire, or cut it and just have it go to the pink one?
Hi, no the auto antenna wire is a different one. that should connect to your radio antenna cable (also blue one). You need to find a different wire and I would sai if you need to connect one. Cut into the sheathing, squish the cable together a bit so the internal wire come apart a bit and thread the new wire through those gaps. Then twist. Plus electrical tape or even better, solder. Should work best.
Hello brother i cant find the amp cable thats running from the harness, I know my harness should have the cable but it doesn't, the amp control cable is as you mentioned, but de amp cable from the harness isnt ,hope you could help me telling me in which pin does the amp cable is
Hmm I have heard this before. Can you check the main wiring harness and see if there is a cable that is the same color as the amp cable? Or in the wiring diagram they give you what pin should have the amo cable go to it and trace it back?
@snipermakedonski hello, can you draw where is the origin of the amp cable which comes from the harness? I have the amp ctrl but not the harness one
Hi, i just received my cc3 unit, expecting to find two amp wires. Only have one but ant wires. I have golf mk6. Am i short or not needed you think?
Oeee, I would honestly not be sure. If there are no wires at all I think you should be fine then. Try and install it and use the fader in the audio settings to move the sound around. If certain speakers dont work (due to missing wires for example) you should really notice it there.
I finally got rid of my garbage Soarcomer head unit (that was not compatible with wired Apple CarPlay and could never reconnect wirelessly without a complete power cycle / cold start) and bought a T'EYES CC3 2K instead. It seems much more well made. So I have a look at your video again before installing it.
You say at 2:05 to disconnect the red ACC wire from the ISO connector (that goes nowhere indeed as the ISO connector is not used) and connect it instead to the red ACC wire coming from the main 16-pin power connector of the head unit (the 'G' block). That makes sense. However, where does the ACC current flow from? There is absolutely no other remote ACC wire available on the harness to connect to the remote ACC wire that runs in the dash from the fuse box, and there is no ACC power cable in the Audi Quadlock used, only the BAT (constant voltage) one there. In this configuration, I don't even understand how your head unit can boot!
EDIT: Wow, I connected as you said and… it works! 😶 And I really don't know why, as the independent ACC wire coming from the fuse box is not used. Maybe the unit actually boots with a digital signal from the CANbus, then provides +12VDC on its ACC wire from BAT? Anyway, the unit is gorgeous, much snappier and responsive than the crappy previous one :)
Good to hear! The ACC IIRC comes from another main wire in the original quadlock. Its illogical but that is why it took me 3 days to figure it out and I thought the unit was broken!
@@snipermakedonski Good to know! For the previous Android HU I briefly had, it didn't work before I run a dedicated ACC wire myself from the fuse box. I was really surprised when the CC3 powered on without actually connecting that additional wire! Thank you for your video, it helped me a lot 👍
@@fluxcapacitor :)
Hello I just plugged the harness in but I’m not sure which red and white white I connect also I don’t think I have the other end of the amp wire
There should be red and white in and out. Connect the corresponding colors of in and out to eachother. I am not sure on the amp wire TBH. Are you sure there is no second AMP wire? Otherwise ask Teyes Support, they are very helpful.
Hello friend, I have a question, when you have to disassemble the radio, how do you remove it if it does not have a removable one?
It should always be. They never are not removable. You need 4 keys for in the slots around the edge and then you can pull it out.
Hello brother, my back speakers and the subwoofer don’t work, to make them work I have to buy the 1v to 4v adapter no? Which are the conexions that I have to make
Yes you need to buy the harness to make them work. its the exact same issue I had. its this one: teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt
Hi.
I bought the lux one for audi a4, and after i connect the quad lock, the buttons near the shifter will not work anymore. The order was right for my model, but i dont know if i received the correct cables.
The air conditioning cables dont fit also. Any sugestions ? I see you have a canbus box on cc3, none of this on the one lux model
What do you mean Lux model? Can you link me?
@@snipermakedonski i did a reasearch, and i found that the shop wich i paid to mount my navigation, had no clue what the cables were for. There is a bypass on the canbus also, but they told me that cable dont fit in the airconditioning module, and i got the wrong cable 😃
@@xpnexus2265 Ahh ok. Would make sense as its all plug and play
I bought an android stereo it came with the impedance adapter, without it only the front speakers sound. my question is: where the 4 impedance adapter wires are connected?
They should connect to the left and right in of the new head unit,
Good night!
On my head unit I have a cable that says "subwoofer" but I don't see where I can connect it. You know it?
Hello! That is only if you have an aftermarket subwoofer and there is a cable for that. Stock you dont have to connect it.
Once the head unit is installed, how do you remove it? It clips in with four plastic clips. Do you just pry it out? I need to order the antenna adapter.
Its very hard, you need to use plastic pry tools, however. I reccommend just not screwing the unit to the frame. Then you can just put a nail around the side of the glass and pull up. Or with a suction cup.
@@snipermakedonski Thanks so much.
Hey, just wondering if your fade/balance control works?
Hey, yes it works 100%. If you cont connect the amps and dont have the harness, it will only work on left and right with just front spreakers working.
@@snipermakedonski Thanks! Hopefully it works well on my TT mk2
@@Gershy13 Hope it does for you!
Hey mate I’ve got the standard non Bose in my a3 and no rear speaker sound what’s the link for the connector you got? Cheers
Hi mate, sorry for the late response, this is it, just check if the website is the right one for you in terms of location: teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt?shpxid=056495a5-8c7d-4be3-9bae-ea69a616de97
Hi mate I purchased this but still not working
Hi there, I am looking for some advise really. I have purchased an xtrons IA series unit for my 2006 Audi A4 with quad lock. They sent the unit with a BOSE adaptor, which I used as I have Bose system. I got allot of static problems when the lights were on and rustling noise constantly. I contacted Xtrons and they sent me a high to
Low impedance adapters free of charge. When I tried to use it one of the rear female phono ports was faulty and only a faint sound coming out when I turned the volume right up. I then purchased a 2nd hand adaptor and that worked fine for about two weeks but has since stopped working with the exact same problem. Can you advise what might be causing the issue? Thank you in advance for your help.
Hmm not 100% sure. Might be fluctuating voltage. You might need a filter. Here is a link on the Teyes website but you can find them more online: teyes.eu/products/teyes-power-filter
Also dont turn it up all the way, keep it in the middle, too much is bad. Try the sound settings and see if there is a power mode in the settings to boost the loudness. Teyes has that in the software. Let me know if it works!
@@snipermakedonski yeah I basically need that but for quadlock. I am using the xtrons one but it’s cheap looking and convinced they are faulty. Can send pics if you want.
@@jasonpoulton865 I would order the one from Teyes then as they also suggest that one I linked for quadlock. I would send their customer service a message with the question on how to install it just in case. They helped me a lot.
@@snipermakedonski cheers mate 😃
I am confused about the adapter and Bose systems. Some say if you have Bose you need the adapter while others say you dont. Witch one is it?? Many thanks
I personally did not know but see this comments:
@HARRYMWAI
If your audi a3 has got rear amplified speakers then just get the 49 AUD 02 harness and this will work 100%
If you've got fully amplified speakers then get the 49 AUD 02 BOSE
@@snipermakedonskiesto es para convertir arnés ISO a quadclock, no se ve que sea de quadclock a quadclock
ANYONE PLEASE I need help, where do I link the electric cables that come from the amplifier? He only talks about the white and red one
I said in the video. You connect the amp C and blue amp cable. Look in the video and pause where needed.
Hi, after I connect the amp wire my rear speakers are still not working. What should I do?
Do you have the extra harnes? And did you turn on the amp in the settings?
I’m having issues with my radio not turning off at all
Hi, I am having a problem (I am in BOSE) when I connect everything woprks fine BUT I do not have audio
Hmm, I dont have bose so I would not know honestly,but did you a turn on the amp in the settings and b contact Teyes technical support?
Thank u thank u 🙏🙏🙏
Glad to help!
It was the 2 amp remote wires that got me. Spent half a day messing about with the ground on my amp. Since when do they have 2 amp wires 😂 thanks again
@@krisparry5968 Yea I know that exact issue, good you found it!
Mate will this wiring work on audi tt mrk 2 I've had a nightmare of time. Your video is very helpfull cheers mate keep up the good work I've not got amp wire connect and the sound is very muffled hope joining the amp wire will sort it out
Glad to hear the video helped! What modelyear is your TT? And do you have the same connectors? If so then it should. Also, if the amp is working but muffled it might be the 2 screws in the impedance harness, try turning those. You are non bose right?
@snipermakedonski hi mate it 2013 plate mrk 2 audi tt I have only the 1 amp wire not the 2 as you have should the amp wire be connected to 12 volt am just waiting on the lead to arrive thanks non bose
@@MrJoelcc9 Interesting. Strange that there is only 1 wire. And there is no second blue and white or blue cable with a cap on it? At all? Then it maaybe should be connected to the 12V but be carefull, if the arm is powered all hte time it might drain the battery.
@snipermakedonski hi yes mate have blue. And white wire but labeled auto ant and the blue wire labeled amp
@@MrJoelcc9 Hmmm I do not think those 2 need to be connected but I would say give it a try! Better than nothing!
Please can you help ive fitted the unit into my audi a4 and have no sound from front right or rear + no amp wire from iso, amp control wire from the back off the unit is black not blue and white
Oeee that is a hard one. Have you turned on the amp? And did you message teyes support yet?
@@snipermakedonski not been in in touch with Teyes yet next step thanks
Do I need to connect the blue cable attached to the radio antenna to anything?
No, I have not and it all works!
@@snipermakedonski Thanks man, you rock!
These 2 AUX cables coming from the harness (in L and in R)
Do I plug them into the other AUX cables or the RCA?
Because I tried both options and I still have no sound..
Thanks 🙌
IIRC it should be the aux cables. aka the reverse (female leads) of the main harness. The RCA cables are for an aftermarket system I believe as they also have a separate bass control. If you dont have sound, check the settings on the screps in the additional harness if they are set wrong they will also give 0 sound.
@@snipermakedonskiwhat is screps?
coz i’ve done everything you said in the video but it doesn’t make any sound
@@tommytm4481 I meant screen
@@tommytm4481 Hmmm I would not know without seeing the wiring. Have youcontacted Teyes support?
Hi I’ve installed my head unit but it will not power off at all if I don’t unplug that plastic clip on your video
Which plastic clip do you mean?
hey very nice video ! I have trouble with my steering wheel buttons... do you have info ? I saw in some forums that i have to connect "key1" wire with ground and "key2" with another wire... please help me :)
Ahh I sadly dont have steering wheel buttons but IIR there should be a set of wires that connects to key 1 and 2 indeed OR it should be CANBUS driven. Did you set up the canbus profile correctly in the settings on the unit? It could be that that is what is missing and then you need to program the buttons.
Otherwise you need to look up wiring diagrams for the car and find the 2 cables on the harness that are for the steering wheel buttons and hook those up to key 1 and 2.
try this man, connect wifi, go to settings, factory and then type the password which probably is “8888”, go to “car model” or something like that, press “LZ” then “Audi” then “A3” and finally “04~12”, confirm. The steering wheel controls should work after it. peace!
@@pedropercu7368 hey thank you, im tring this right now but when go to « Lz » I found « A4,Q5 » or « A5 high profile »….
Does GPS work for you? and what should i do if con settings doesn't load up?
Yes but make sure yo have the antenna plugged in and routed to ABOVE your dash. Otherwise it wont work. It needs clear sight through the glass.
Which settings do you mean?
@@snipermakedonski hm, sadly mine doesn't catch up nothing, even i routed it outside from dash hmmm.. settings i meant about " can bus settings " it show the lists, i try to choose mine car settings and after little of loading it says failed
@@ComedyBow Hmm for the CANBUS, did you select the correct box? The one you got supplied? IIRC mine was a binary one.
For the GPS, try rebooting by dragging down from the top. I had that exact issue and a reboot fixed it. Its different from turning it off.
@@snipermakedonski well i didn't had any other, just that one which was implemented in the box
@@ComedyBow Hmm you should have a CANBUS box, check the manual. It might have already been connected but if not there is your problem. I would also check if that is the right one selected or not.
Hi i have a problem with this radio. I connect all cable like you but I have no sound. I have only a noise. Audi a4 b7 bose system. Can you help me 😢?
Hmm, did you turn the little knobs on the impedance harness? The transparten ones in the middle harness? Try turning on music and turning those actively. Also see if your amplifier is on in the settings
Hi bro, i bought the harness and installed it back speakers do work but still my multimedia doesnt recognize the amp and the sound is not even close to the factory one. Any tips and tricks?
How do you mean does not recognize? Did you turn on the amp in the sound settings in the software? Otherwise turn on loud mode in the equalizer and or power sound in the normal sound settings. Let me know if it works!
In settings i have setting for music when i enter those settings in the top left corner it says unknown amplifier and when i try to change bass, fader etc nothing happens. Yes i have turned on amp in settings. I have tried loudness on off but no luck.
@@dadoAprilliaHmm sadly I dont know. This is really strange. Contact Teyes would be the best option. Sorry!
Hello, please help! I've been having so many issues ever since I installed my Cc3 into my 16 Hyundai Veloster Turbo that if I told you, you would be like OMG! 😮 But I came out of it. And I did what you said about blue wires for the amp, and now I get no sound coming from my speakers. I'm not sure what to do know. Before, I did get some sound from the front, but now nothing after splicing the blue wires. I would appreciate any suggestions. Thank you
Hi! I understand the frustration. I had the same. So in the settings menu for audio, did you turn on the amp with the toggle? Also have you tried raising the power level in the settings?
@@snipermakedonski Hello, sorry for my delay in responding. Omg it seems like I fix one problem and the next day a new one will pop-up! So, I fixed the no sound problem. But now I'm not sure if the factory Amp is working because. When I switch off the amp in the teyes equalizer app I hear no difference in sound volume. Also do I need to connect the Key1 and key2 wires? And I get no (vehicle information) in the vehicle information app. I can't go to Teyes support because I didn't purchase my head unit directly from them. Thanks for your quick response and I would appreciate any suggestions you can provide. Thanks
@@lou.242 Ahh ok. If you have a car with multifucntion buttons on the steeringwheel (basically any buttons at all), then you need to connect the key 1 or 2 (depending on the wires coming from your car wiring loom included in the box) wires. If you dont get any vehicle information in the app, you need to probably set the right canbus settings. Look in the teyes app for instructions or online. I know for my car I got a (I think) brown canbus box which was binary and then in the settings I selected that, box, then audi a3 etc. and that should help. Otherwise you probably need the OBD dongle. Hope it works!
Hey!do you have an link for the site!?or what it is the name of the harness?thank you! 👋👋
Yes I do here: www.teyes.com.au/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt
On the A3 i have the iso harness it is not the quadlock!do you have any ideea where can i find one!i searched over the internet,no chance!
@@adrianionita7211 Sadly no, i dony know if they exist. Maybe message Teyes support? They know quite a lot.
Thanks for this Video, I have put in a few days in the installation now, and I stucked with no sound...Audi TT MK2 from 2014 - I have perfect image, the Steering wheel controls works fine, but no sound, did order the addional adapter cable with the "Special Power Adapter Cable with Audio Amplifier Cable for Audi A3/A4/TT" I Do not have the Bose version of speakers, and have the "OEM Audi TT Trunk Amplifier 8j0-035-223-f" Please support me with how to solve the sound issue. If i connect the OEM stereo from Audi the sounds is perfect, so no issues with the cables etc in the car. Thank you.
Hi, hmm strange is there anything strange you notice? Buzzing? Not connected cables? did you change the screw settings on the power adapter cable?
@@snipermakedonski thanks for reply, No, all was good, and I have been at 2 different "Car stereo" shops, And they have not been able to fix it. If i turn upp the volume to high, the fan on the back start spinning, but maybe that a factory setting?, This is so strange, i have checked maybe 100 different videos on this topic,
Hi! I did finally solve it! It was a simple setting that did cause this issue.
Device - then AMP On/Off and then music in my ear :)
Ahh perfect!!!@@danielpalmkvist
Same here! No sound at all. What do you mean Device Amp on/of?
my friend got the same one, I installed it but the rear speakers don't play. and what worries me the most is that I don't know how to unclip it. Can someone help?
Unclip the frame? Its really tight. You need trik removal tools. Rear speakers is you are missing the middle harness. The low to high impedance. Teyes sells one
Hey I did install the car Audi I have problem which is my rear spkeakers does not work how do you connect k28
What is K28? Do you have the harness?
@@snipermakedonski yea I have the harness I don’t know where to contact the harness I know that I can connect red and white amp to it but I don’t know where to connect the other side of it
@@02any1 That is why the rear sperakers are not working. Connect one end to the main harness coming from the car and the other end into the main harness of the headunit. Look in the video to see. Also look on the Teyes sale website for the unit. It has a wiring harness.
@@snipermakedonski cheers brother I really appreciate it 🙏🏾
Hi .very nice and good information.
I don't have a Audi but a Citroen C5 x7 . I have the same problem .no sound back and my subwoofer is not working properly.
How can come in touch with you ?
Regards Tibor
Hello I always write here. But I have 0 knowledge about Citroen. Have you installed an aftermarket teyes radio?
On mine is all connected and i still have 2 error codes in obd, on infotaiment error and no radio error
Hmm, for the radio, did you have the right cable? And what do the errors say? Is something not working?
Hi after a bit of help if you don't mind. When you receive a call, without car play open, do you get a phone number or the contacts name come up?
Yes you get the number or if you have synced your contacts it will also show the name of the person calling.
@@snipermakedonski Contacts synced but get the number, Spoke to teyes too, they don't get why either Thanks though
@@A38P Hmm strange. And teyes not knowing? what phone do you have? Did you also check settings in the options menu? Maybe there is a switch you need to change?
@@snipermakedonski s21 tried it with iphone and an oppo I can't see anything to change it from showing the number, rather than the contact name. Open car play shows the name, strange
@@A38P Did you actually sync the contacts within the bluetooth phone app on the
device?
Does your A3 have Bose?
No it does not.
@@snipermakedonski Nor does mine but I didn't need this loom, for the rears to work. (spoke on xda by pm ;) )
@@A38P Ahh it was you! Ok, good to hear!
Hello friend, sorry because I don't know English and it doesn't translate what I want, I ask you how to remove the radio because I have the same Audi A3 car and the same new radio to install and I understand that if the plastic casing is mounted and you screw it to the plastic and you mount it definitively to the car it does not come out anymore since there is no way to remove the casing it does not have any slot, that is what I ask you how do you remove it friend
Ahhh I understand now. No problem!
So yes if you screw it into the plastic frame and then put it in (after connecting the cables), it will click in (it will be VERY difficult to get in) and getting it out will be alsmost not possible. That is why I advise not screwing it onto there. removing it, screwed in or not requires plastic trim removal tools like this: www.amazon.nl/Tresalto-verwijderen-deurpanelen-bevestigingsmiddelen-dashboards/dp/B01L8GHB7O
You get it behind one of the edges of the plastic and gently try to get it out.
Hello friend, greetings from Spain, I have a problem with my radio, I have a problem that the touch does not work just like that, let me explain, you touch the screen and it does not respond if I turn off the car and start it, that's how it works but it does it every time but it's very strange, as I explained, the radio works but you touch the screen and you can't do anything or put voice on, remove or anything, it's very strange, does that happen to you too? Thank you and greetings from Spain
Hello! I have not had that issue but have you tried recalibrating touch in the settings? Maybe the touch sensing is not correct?
@@snipermakedonski m.ua-cam.com/video/JzNyc3_GAG8/v-deo.html
So u are not on bose right??
No I am not
@@snipermakedonski so i assume with bose system we not need the low to high rca right??
@@nitro_power That I would not know to be honest. I would say, write to Teyes and ask.
@@nitro_power audis without bose still have factory amplifier for rear speakers which do need the high to low adapters (or adjust the settings in fader app)
@@MichaelFlatman i have bose amplifier and next week i will install my head unit..wait to see how hard it will be to connect
Bro, please help im in desperate need
Sure but I cant help if you dont say what the issue is...
@snipermakedonski I have an android head unit I installed Everything I got a ISO connector to 16pin connector for the headunit, and the rear speakers are not working. I have a 2005 audi a3 non bose
@@Samuraiii12 ISO to 16 pin I don`t know anything about, sorry. Is it not a Teyes?
@snipermakedonski it's a ACODO 9inch and the connector is with canbus (btw are you macedonian ?)
@@Samuraiii12 Hmm do you have have high to low impedance connector? And no I am Dutch but I get the logic :)
Teyes has a good product but the introductions are very poor
Oh yea but their customer service is great.
@@snipermakedonski okay I will email on what I need to get my steering controls back
En français svp merci
Sadly I dont speak fuelt enough french to do that but you can auto translate my post on the XDA forums! forum.xda-developers.com/t/teyes-australia.4240385/page-26#post-88059851
Hello,
please, i would like to know if you have succeeded in displaying icon information of the vehicle. the canbus provided for audi a3 TZY 20220610.
Hello, what do you mean exactly? I setup my canbus and all seems to work. I do not however have a multifucntion steeringwheel so did not need to programme things.
Can someone send me the link to purchase the harness?
Here you go! teyes.eu/products/special-power-adapter-cable-with-audio-amplifier-cable-for-audi-a3-a4-tt?shpxid=fa8061e3-f1af-4eb3-8648-179838afac50