Experimental Hang Glider Project | Deneysel Yelken Kanat Projesi #1

Поділитися
Вставка
  • Опубліковано 11 гру 2024

КОМЕНТАРІ • 23

  • @emrecivelekoglu37
    @emrecivelekoglu37  2 роки тому

    Turkish: Bu proje hakkında daha fazla bilgi için lütfen UA-cam profilimde yer alan Topluluk sekmesine bakın.
    English: For more information about this project, please see the Community tab on my UA-cam profile.

  • @mahamed3208
    @mahamed3208 Рік тому +1

    Thank you very much for your ❤😊

  • @AzadAmeen
    @AzadAmeen Рік тому +2

    Really, your work is great, but we need more clarification, especially the measurements. Thank you very much

  • @truckdriver592
    @truckdriver592 Рік тому +1

    to save fuel, it could be slimmer. The wings are too wide. Don't use too many frames to make it easier to control. If it's slim, it can fly anywhere. No need to use motorbikes and planes to go anywhere.

  • @olafpeter8625
    @olafpeter8625 2 місяці тому

    Hi, a friend an me started to build an RC model 1:3 (I'm former hang gliding pilot and pesionaire:-) . We have the form, I have a laser cutter for the sail, actually we are valuing the right materials.
    Is there a possibility to get your DXF-Files, of course condidentially and exclusively, for our RC-model project? We would be happy to share results.
    Our model will have a bigger nose angle, I think (128°), but the construction of the fittings is much work still.

  • @ericoschmitt
    @ericoschmitt Рік тому +1

    How do you expect the weight to shift if the trike base is attached to the base bar?

    • @emrecivelekoglu37
      @emrecivelekoglu37  Рік тому

      Thank you for your comment. First of all, I must admit that the design in this video is very old and there are many mistakes. When I first started developing this Hang Glider, I was a very, very newbie.
      As for the question you asked, the weight shift in this design was planned as in the video below. From 19 seconds.
      ua-cam.com/video/pa61ZeByFuM/v-deo.html
      I will answer the questions you wrote in other videos from the comments of that video.

  • @phakly8366
    @phakly8366 Рік тому +1

    Hello ❤ what is software you use for this project?

  • @osninielsen6933
    @osninielsen6933 8 місяців тому

    Boa tarde , como obter as medidas p/ esse projeto ?

  • @rmu3212
    @rmu3212 2 роки тому

    umarım başarırsın

  • @messaoud.ben.mohamed
    @messaoud.ben.mohamed Рік тому

    جميل جميل ورائع

  • @mustafakucukerdem4593
    @mustafakucukerdem4593 Рік тому

    Selamlar ölçüleri nasıl alabiliriz yapmak istesekustam

    • @emrecivelekoglu37
      @emrecivelekoglu37  Рік тому

      Aleyküm Selam, daha tasarımı oturtamadım be ustam. Uzaktan Kumandalı küçük bir versiyonunu yapmaya çalışıyorum test için(küçük prototip), ama bayağı uğraştırıyor.
      Ayrıca bu videodaki tasarım çok eski yenisi en son yüklediğim.
      Ama kabaca bir ölçü vermek gerekirse UA-cam profilimdeki 'Topluluk' sekmesine bakın.

    • @emrecivelekoglu37
      @emrecivelekoglu37  Рік тому

      Ayrıca sadece ölçüler işinize yaramayacaktır, bunun Washout derecesi var kanat profili yani batenleri var ağırlık merkezinin dengesi var varoğlu var.
      Sadece bu ölçülerle yapmaya kalkarsanız malzemeler elinizde kalır.

    • @emrecivelekoglu37
      @emrecivelekoglu37  Рік тому

      Kısacası proje hazır değil, henüz.

  • @David-ls1hw
    @David-ls1hw Рік тому

    Hola
    ¿Tienes los planos en PDF con medidas?

    • @ericoschmitt
      @ericoschmitt Рік тому

      This is an unfinished and untested sketch of a project, with no sail cut design yet made (arguably the most important aspect of handling and safety), so I wouldn't recommend trying to build. Even with plans, it would be tricky to source individual tubes to build a single glider, and probably cheaper to just buy one made at a factory.

  • @sollsern2643
    @sollsern2643 Рік тому

    There is a tutorial yo make one of this ?

    • @emrecivelekoglu37
      @emrecivelekoglu37  Рік тому

      I haven't gotten to the build phase yet, because I want to make sure everything is alright.
      If I am convinced that the design is completely finished, I will start the construction. You will be able to watch the construction process on UA-cam.

  • @rmu3212
    @rmu3212 2 роки тому

    uygulamanın ismi nedir

    • @emrecivelekoglu37
      @emrecivelekoglu37  2 роки тому

      Uygulama SketchUp 3D modelleme yazılımı, 3D model daha geliştirilme aşamasında. :)

  • @IbrahimHossin-jt1wz
    @IbrahimHossin-jt1wz 10 місяців тому

    কোন দেশ,,