Now in 2021...would you get the Gold FX or the Black Influencer Deep Tooth trimmers? I like the black ones better but I don't know if they will be as good. Thanks Ricardo!
Só queria saber que câmera que esse gringo tá usando, ela foca e desfoca muito bem, e essa máquina Skeleton ainda não chegou no Brasil, aqui as coisas são muito atrasadas mesmo
Hey guys I need help.. I just bought these new trimmers today and they pulled all of my clients hair. I lubricated them, readjusted them multiple times and they still pulled hair. Anyone else experience that or know what else I could do to fix it?
Mooney same problem here bro. You find any helpful info on how to fix that? Slim line pros are my go to. I was hoping these bad boys work as good or better but they keep pulling.
Whay in same babyliss gold fx is written,3 hours running and in same is 2 hours. And they look totally the same?? And they go from 130€-400€. What is the difference?
I got these and use them daily at a busy shop. One HUGE downside is that they get super loud the second I spray Cool Care on them between cuts. They stay loud for a while and it's killing me. I'm about to return these and buy the cordless T-Outliner again.
@@VISlXVI I agree! I ended up returning my Babyliss Skeletons, purchased the new Wahl Cordless Detailer Li and sold those. I didn't like how they hit. I did just recently purchased the T-Outliner Cordless and the GTX blade. Hittassss and it doesn't matter how much I disinfect them, they are silent. Super happy with my decision. Now waiting on the Cordless Master to drop.
Hey bud thanks for this great review! I have a question that you might be able to help. I adjust the blade and looks pretty even and close but for some reason no matter what I do the right corner bites a little? Is there anything you can tell me? There are 3 barbers in my shop and I’m the only one with them and we can’t figure it out? Thanks man
Weird their rotary and shouldn’t do that.hold the edges of the blade and see if one side hits your finger harder than the other while running. If so unloose top screws and adjust the top blade left or right slightly and retighten.might fix your problem but it might not. Lmk
Lol. I still have the blade but once i took it off and installed the ceramic blade they were killer. Just didnt accept the nano guards. Ill try to do the video either way. Slightly on the chooping block. Hopeully im free and bored one day
The tool i got to loosen up the screws under the blade is either too small for the screws or it stripped the screws already. Does anybody else had this problem?
To be honest I don't believe babyliss makes any of their products, they just get a Chinese company to make whatever with their name on it, way too many copies of this clipper from china that are actually good too, that being said these are the best ones and still a very good trimmer, overpriced but very good.
man you killed !! im a barber and that lean the machine back was genius
Just got a pair and could not get them adjusted until the lean tip. Great vid
I just got some and man these clippers are just FIRE!
Bruh thank u. Got my boys HITTING SO HARD
Straight to the point! Loved this!
Short and to the point 🙌🏽
That’s exactly how I zero GAp all my tools well trimmers . Great work man
Dope video bro. I just subscribed due to your expertise on adjusting the gold fxs.... Perfect adjustment. Gratitude fam
Great vid. These are definitely some hittaz! Much respect. 💯
Best Damn Trimmers Ever!!!!! Thank you 🙏🏾
I just got mine a couple days ago. They truly are a game changer
Straight fire bro
Can you get in Uk ?
Can you do a update on your barber station?! And if you using any new products or tools do some reviews. Glad to see u back dude!
Yes i can. Its definitely evolved over the years. Thanks for the support
6:08 for the adjustment.. these trimmers pull hair so much though, for anyone with big follicles do not use
My man Ricardo! It’s been awhile
Im here just need heads to cut lol
Now in 2021...would you get the Gold FX or the Black Influencer Deep Tooth trimmers? I like the black ones better but I don't know if they will be as good. Thanks Ricardo!
The black ones were made better with smoother blade but im sticking with the original golds because it's the sharpest blade they made.
@@kikado3 thanks brother!
Just got mine a couple weeks ago but with the black dlc blade on it. I been hearing that the gold blade hits harder thinking about swapping it
Só queria saber que câmera que esse gringo tá usando, ela foca e desfoca muito bem, e essa máquina Skeleton ainda não chegou no Brasil, aqui as coisas são muito atrasadas mesmo
I have that on gunsteel color but I have heat issues on the first haircut. You have the same problem on gold?
No never had this issue. Blade might heat up after long use which is no problem but the clipper never gets hot at all.
Dope review! 👏👏👏👊🏻💈✂️
I like them but why do they get so loud??
Best review I seen out on UA-cam ‼️
Hey guys I need help.. I just bought these new trimmers today and they pulled all of my clients hair. I lubricated them, readjusted them multiple times and they still pulled hair. Anyone else experience that or know what else I could do to fix it?
Mooney same problem here bro. You find any helpful info on how to fix that? Slim line pros are my go to. I was hoping these bad boys work as good or better but they keep pulling.
Mine pull how do I fix them
Change the blade
If u can find blade not babyliss brand better
Anyone know where i can purchase a replacement zero-gap tool kit the little screw driver to loosen and tighten the blades broke from its handle😧
Bring trimmer to home depot they have plent of allen wrenches that would fit.
Ricardo The Barber word ok kool I didnt know 👍🏾
Hello ricardo, is it working with 220v? Or just 110v!
Regards.
Solid review thanks bro.
Just got this and mine came with a zero gap tool and no fx blade 🤔
how many grams is this machine? lighter or heavier than a detailer?
They come with a tool that you slide the blade into so you can zero gap them a lot easier then this video
Antonio Sanchez I used the tool but it pushes the bottom blade way too high.
Jose Salazar when the top is over lapping just take your thumb and tap it down till it’s even with the blade a bout 2-3 hair strains
Whay in same babyliss gold fx is written,3 hours running and in same is 2 hours. And they look totally the same??
And they go from 130€-400€. What is the difference?
I got these and use them daily at a busy shop. One HUGE downside is that they get super loud the second I spray Cool Care on them between cuts. They stay loud for a while and it's killing me. I'm about to return these and buy the cordless T-Outliner again.
Don't use cool care on em they are trimmers, completely unnessecary just brush them with the cleaning tool it comes with
@@marcthebarber239 why is it unnecessary to sanitize the tool??
@@gamebred5x because If you consistently brush them off and clean them you don't gotta spray a sanitizer on them unless your cutting homeless people
432Marc i disagree.. you must sanitize your clippers after every couple cuts at least.. Sorry just how i rock.
@@VISlXVI I agree! I ended up returning my Babyliss Skeletons, purchased the new Wahl Cordless Detailer Li and sold those. I didn't like how they hit. I did just recently purchased the T-Outliner Cordless and the GTX blade. Hittassss and it doesn't matter how much I disinfect them, they are silent. Super happy with my decision. Now waiting on the Cordless Master to drop.
I can’t wait to get mine
I use a Andis T Outliner to do a full cut can these cut as close and handle a full cut before balding out a head? Thanks
Do the blades or the clippers it self get hot fast
These are not too bad.
Hey bud thanks for this great review! I have a question that you might be able to help. I adjust the blade and looks pretty even and close but for some reason no matter what I do the right corner bites a little? Is there anything you can tell me? There are 3 barbers in my shop and I’m the only one with them and we can’t figure it out? Thanks man
Weird their rotary and shouldn’t do that.hold the edges of the blade and see if one side hits your finger harder than the other while running. If so unloose top screws and adjust the top blade left or right slightly and retighten.might fix your problem but it might not. Lmk
Can i use wahl clipper oil on babyliss clippers?
Yes
Awesome review 🙋♂️🙋♂️🙋♂️
I zero gap them and when I do hairlines or line someone up they don’t feel anything but once I do beard, it pulls and starts cutting, any solutions?
Yes. You have to hold the cliplers flat to the head when shaving down hair. Its basically a fade blade so it can pull skin if you dont.
Bro I’m having a problem setting mines
TheStarsBarber same- asking other barber friends and no one else has them. This sucks. So pumped to use them but can’t set it to cut right...
Nice job
Do they sell clips for this trimmer ?
I got the silver with graphite blade
I want any deep tooth blade they make. I tried the rose gold and its better than the regular gold.
Yes this 2.0 graphite blade is amazing
A skeleton red é melhor será?
Gracias my boi
Do you have any of their clippers? If so, do you like them and can you zerogap them easy also?
Yes i do. You can zero gap them but i hated both pair of clippers i had and got rid of them.
Do you have to zero gap them out of the box . Mine bite and nick me and pluck me out of the box why ????
You on point about that’s blade very thin
What happened with the magic clip/andis master blade mod? Is that still a go? Lol
Lol. I still have the blade but once i took it off and installed the ceramic blade they were killer. Just didnt accept the nano guards. Ill try to do the video either way. Slightly on the chooping block. Hopeully im free and bored one day
Someone pleeease tell me where to get these I'm looking everywhere 😩
432Marc same bruh can’t find them anywhere
432Marc universal barber app
CosmoProf
Atlantabarabers.com
614 barber supply
Thank you sir!
I took apart my entire shit lol. Can’t get em back together. Any help?
Damn, hope you figured it out bro...
The tool i got to loosen up the screws under the blade is either too small for the screws or it stripped the screws already. Does anybody else had this problem?
upload more often man
Kids are a bit older, saturdays are now free and i just resigned with my youtube company. More on the way bro
TheY don’t hit like my andis t outliners I’m sorry it’s cute tho
Mys getting hotter on the blades why is that?
Prob needs to be sprayed with cool care
@@kikado3 i did
Wow if it gets hot fast theres something wrong with the machine.
@@kikado3 noooooo i didnt want to hear that but i think maybe
Where do you buy these?
Cosmo prof has them in stock
My main man Ricardo where you been? man you look like you to slim down! Lol
Lol busy with my 3 little monsters. Thanks bro back in effect
I thought I was watching someone else. And, he look very clean, too.
Do you have a telegram
How would this compare to the slimline pro li?
Smashes the slimline pro
My screws are fukn glued on they do not move at all and now the screws are fukd up man, they need a better screw driver for this
good
Mine are glued wtf
My shits were hitting till I Zero gapped now idk wtf is going on but they snag like a mf
Thats weird. Im not having that issue. Maybe the blades a little crooked???
To be honest I don't believe babyliss makes any of their products, they just get a Chinese company to make whatever with their name on it, way too many copies of this clipper from china that are actually good too, that being said these are the best ones and still a very good trimmer, overpriced but very good.
A lot of companies do the same thing
Wat is that shuttering noise that keeps happening thru the video??? Shit is irritating af
Cmon stop crying 😢
Thank u …✊🏾💈