Control Linear Slide Rail Guid with Arduino - Banggood

This video is about Banggood 300mm Stroke Linear Actuator CNC Lead Screw Linear Slide Rail Guide with 42 Stepper Motor
=========================================
WHERE TO BUY ➝ bit.ly/2PdFZ9K
=========================================
Hardware
1. Arduino UNO
2. TB6560 Stepper driver
3. Lead Screw Linear Slide Rail Guide
4. Jumper wires
Arduino Sketch
bit.ly/2IAkzTj
:::::::::: SUPPORT CHANNEL ========
Please Donate To Help Me Afford New Equipment And Software To Make My Videos More : goo.gl/1m8Dg2
→ Don't forget to subscribe!
🌟Love you all! 💕
Song: MBB - Fresh (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • MBB - Fresh (Vlog No C...

[@Reach3DPrinters]

38 sodas were opened during the recording of the background music.

[@JohnWayne99999a]

Looooool

[@lifeissimple2323]

Hello, did you make any changes in the code to rotate the motor in anticlockwise direction? Because our motor is rotating in only one direction,even after making direction pin to low.

[@arnoldgarcia8688]

What is the enpin for? Why is there a note saying you are doing 400 pulses when the code is the same for 200 pulses?

[@mattialimoncin3781]

I have a NEMA17 12V 0.4A 1.8deg stepper motor. How can I set the limit current with the TB6560 driver?

[@steveughhh]

When you are connecting CLK-, CW-, EN- to Arduino GND, What is that 3pin connector used? 3 in 1 configuration

[@mayurtolanure949]

In the given code what changes should I make to make useful for 1000mm lead screw?

[@rakeshelectricals1720]

Can we run this motor only with tb6560 stepper driver without useIng Arduino

[@bobje999]

Hi! very good video, it helped me a lot. Could you please tell me (or link) what an appropriate power supply would be for this stepper motor? I have trouble finding a power supply

[@tigergirl411]

Hi! At 1:21 is the motor specifications. You’ll want to power the motor at its specified 12V, so you’ll need a power supply that outputs 12V. A certain model isn’t necessary as long it meets the motors power (Volts & Amps) specs. Hope that helps!

[@tigergirl411]

Oh and i forgot to mention that if you Google the model name, you can pull up the data sheet that will give you info about the motor, how it should be used & all that technical stuff

[@khanfamily2745]

Nice work .. thanks for this video

[@andrescuenca1122]

Amazing! Thanks for sharing this! How fast can can this mechanism go?

[@dianamolodtsova3422]

I have the same question did you try the mechanism? :)

[@InterstellarRanger]

@@dianamolodtsova3422 Depends on the stepper motor. The more powerful faster it will go. You are only limited by the liner rail support and power supply.

[@dianamolodtsova3422]

@@InterstellarRanger yes I finally figured it out but for what I needed the stepper was too big :(

[@carbkafv]

Does this work vertically as well? Will it slip?

[@mohanadmohsen]

Good work, please do Bescor MP-101 Pan Tilt Head with Arduino

[@mokuroglucnc]

thanks for sharing

[@kennethfajardo5121]

what is the lead of lead scrrew?

[@shafiqalom8408]

Nice video❤

[@djurokovac]

Welche accu kann ich benutzen danke

[@TravisNobles]

Your end screen cards block the entire end of the video where the device is actually working (they pop up about 20 seconds before the end of the video)... really wish youtube channels would stop destroying their videos with these..

[@rickpercy87]

Is there a way to increase the speed?

[@raifhanna1120]

For this driver, what is the maximum motor Amp can I attach to it?????

[@MakerTutor101]

Thanks for watching. Max 2A for safty but driver spec 3A

[@Circuitoptimize23]

😍😍😍

[@AbnuCPaul]

Nice 👌

[@jagarutikorat3522]

how can buy you

[@MakerTutor101]

WHERE TO BUY :: bit.ly/2Vsjgrh

[@er.7755]

Can’t people tell us what’s going on?