Just saved my life , bought a PS4 on offer up for 50$ , had roaches in the power supply dead laying on top of the board , after cleaning , started up fine
Hi, i have the same psu ADP 200ER with a faulty mosfet (the one on the rightest corner)--->stps20lcd60c /// GF 089 /// VW CHN 541. Can you tell me what mosfet i need for repair? Thx in advance!
Are you able to tell me which values of a mosfet are important when looking for a replacement? specifically an n-ch mosfet K10A60E on a ps4 adp-200 power supply
Hello, I congratulate you very good the videos Have you ever fixed an ADP-200ER with the 3n62k3 mosfet and resistance 16.8 (short) in the model ADP-200ER change the mosfet 3n62k3 and the resistance 16.8 and when the test burns again the mosfet 3n62k3 and the resistance 16.8 Do you have any advice that can help me?
Hi, same PSU the 12v where going the two long pin in the motherboard, when I tested in the PSU I don't have voltage, is normal or thats the problem with the blue light only????
I have the same ADP-200ER model. But in my case, PS4 console turn off without red light. Do you have any advice or resolve about this problem??? Thanks
Hello, I am not sure, but the value of the original (fat) fusible resistor is 0.16 Ohms? Am I reading it wrong? And you changed it to a 16.2 Ohms? Or am I overlooking something? Regards,
@@ToltecMerc, thank you. It's color code as here: www.globalspec.com/learnmore/electrical_electronic_components/passive_electronic_components/resistors
Game Console Repair Legion Playstation, Xbox, NES hello I’m reading a color but brown is 1 blu is 6 silver x 10 -2 how to result 16,8 ohm can you explain to me ?
Hello, excellent video. I am trying to repair the ADP-240CR source for ps4, I don't know the differences between the one you repair in the video and the one I am trying to repair. It would have the schematic of the ADP-240CR. They are very similar but I need the schematic. In my case, the source does not turn on or bridge pins 1 and 3 of the connector. Thank you
PS4 Repair 101 Can you help me? I have no power when trying to turn it on but the eject button does beep 3 times. why is that? Is that still a power issue. Tried to look for it and when i messure the voltage when triggered i messure 8 volts..that should be 12v right? Im very handy with Soldering but usally I build quadcopters lol so i dont know much about circuit boards. Hope you can help!
Manuel Smeets it means you have 5v standby power. But your not getting 12v. So. Something on the board is blown/faulty. Follow along with my videos. Most power supplies are pretty much the same.
hi, nice video. may I ask what is the fuse amp rating of that psu? I searched the internet and it says 5ah but mine says it is 4ah. also what would happen if I replace a 4ah fuse with a 5ah? any help would be great thanks
Hey I have the same power supply but my PS4 would turn off randomly. Have confirmed that it's the supply because I ran it off of an ATX supply and it worked. Can you tell what could be an issue??
Hi My ps4 is auto booting to safe mode and menu option not showing error is giving (su-34311-2) SCE_UPDATER_CORE_ERROR_SATABR_FW_GENERAL. Kindly please help if any solution
I am working on one of these which has 5V output, but no 12V, It was causing the Blue light of death. I purchased a replacement PSU and the PS4 works fine now, but I kept the faulty one to repair. I have faults with Q101 and Q102. They say 9990G1 on them. For the life of me I cannot find them to buy or even a alternative mosfet to fit and try. So frustrating when you find the faults but not the spares to fix. :) Any ideas on what exactly Q101 & Q102 can be replaced with. They are identical?
So I ended up finding correct parts for Q101 and Q102 on Ali Express. Still didn't work. No 12v output. With no visible signs of damage, or defect there was little to go on. The 5v output rail working, so I ruled out a lot of primary side issues on the 5V side of things. So I went a littler further back on the 12V side of things and replaced the two surfaced mount transistor IC. Still didn't work. I was about to bin the board, when I decided to short the 5V+ supply rail to the standby pin which WAS NOT pins 1 and 4 on my board on output connector. It was pin 1 and 3 as far as I can remember, or possible 2 and 4. Lets just say it says it on the board which is 5Ve and Standby pins. After shorting the 5V+ rail to standby pin I got 12 Volts switched output. So I have managed to fix it I think. Either that, or there is a switching fault. I had ordered a new one for my sons PS4 ages ago which fixed the original fault PS4 blinking blue light fault due to no 12V. My guess is that the Q101 and Q102. did fix it, but there is also a possibility that the 2 x surface mounted IC's fixed it on the primary side of the 12V rail transformer.
@@josemariacastillolopez5122 Gracias amigo!, compré hace poco una resistencia de 14ohm a 1/2 watio pero al probarlo quemó el mosfet que esta junto y la resistencia :( la verdad no se que sera. intentaré con uno de 15 ohm y le pondre un mosfet nuevo, solo que tardara porque lo pedí por alliexpress. (tengo dos fuentes del mismo modelo ADP200ER y las dos tienen fallas) :(
Amigo José Maria castillo López, entré al grupo de FB de este canal, presenté este problema y al parecer no era de 16.2 ohm sino de 0.16 ohms, la verdad no me siento muy seguro, en el video no distingo muy bien los colores pero sé que son de 5 bandas veré mejor, si tienes más info me lo haces saber por favor 👍✌️
@@xanadusanson621 pasame tu email y te mando una foto de las que pedí,eran de 0.15 ,en el foro de fb hay una publicación mia donde me contestes el autor de este video!!
Just saved my life , bought a PS4 on offer up for 50$ , had roaches in the power supply dead laying on top of the board , after cleaning , started up fine
Seems like the new resistor is smaller thus lower power rating than original. Shouldn't it be a 1watt resistor?
hello thank you for the video, would it be possible to have the reference of the component d101 please? thanks in advance
Thanks for your videos. But always try to explain zoom camera so that your viewers can see well.
Hi, i have the same psu ADP 200ER with a faulty mosfet (the one on the rightest corner)--->stps20lcd60c /// GF 089 /// VW CHN 541.
Can you tell me what mosfet i need for repair?
Thx in advance!
So when I touch them to the resistor I get nothing but when I flip it over and start testing it alerts what's going on
Are you able to tell me which values of a mosfet are important when looking for a replacement? specifically an n-ch mosfet K10A60E on a ps4 adp-200 power supply
Hello, I congratulate you very good the videos
Have you ever fixed an ADP-200ER with the 3n62k3 mosfet and resistance 16.8 (short)
in the model ADP-200ER change the mosfet 3n62k3 and the resistance 16.8 and when the test burns again the mosfet 3n62k3 and the resistance 16.8
Do you have any advice that can help me?
I have the same problem
Did u fine the solution.
Please help
Saludos amigo necesito el valor de las resistencias R3 y R4 por favor de la fuente de poder ADP200ER gracias
Great Video mate, i have a similar psu adp 200-er, capacitor is blown. is it 150uf 450v capacitor ?
Excellent repair!
Hello, i can´t find that resistor in aliexpress or amazon there are some different replacement or similar i can use? thankyou.
Hi, same PSU the 12v where going the two long pin in the motherboard, when I tested in the PSU I don't have voltage, is normal or thats the problem with the blue light only????
Did you discharge the CAP :) Your such a badass.
I have the same ADP-200ER model. But in my case, PS4 console turn off without red light. Do you have any advice or resolve about this problem??? Thanks
the power sources are the same only change the housing?
New fan as found!!! Amazing Work!
Kennedy Gomes thank you
I have a small beep on Q9 do i need to change it? Mi ps4 turns on and off then i hit it o cupple of times and works normaly
Hello, I am not sure, but the value of the original (fat) fusible resistor is 0.16 Ohms? Am I reading it wrong? And you changed it to a 16.2 Ohms? Or am I overlooking something? Regards,
János Gajda going by the color codes. It’s a 16.8 ohms
@@RepairLegion, the color sequence is - brown, blue, *silver,* gold and red. 16.8 does not conform with E192 row.
@@Manfreddis I have one of these supplies in my shop at the moment with a good resistor. It measure .16 ohms or 160 milliohms if you prefer.
@@ToltecMerc, thank you. It's color code as here: www.globalspec.com/learnmore/electrical_electronic_components/passive_electronic_components/resistors
Game Console Repair Legion Playstation, Xbox, NES hello I’m reading a color but brown is 1 blu is 6 silver x 10 -2 how to result 16,8 ohm can you explain to me ?
Hello, excellent video. I am trying to repair the ADP-240CR source for ps4, I don't know the differences between the one you repair in the video and the one I am trying to repair. It would have the schematic of the ADP-240CR. They are very similar but I need the schematic. In my case, the source does not turn on or bridge pins 1 and 3 of the connector. Thank you
Check the fets, PWM ic, Fuses and resistors.
PS4 Repair 101
Can you help me?
I have no power when trying to turn it on but the eject button does beep 3 times. why is that? Is that still a power issue.
Tried to look for it and when i messure the voltage when triggered i messure 8 volts..that should be 12v right?
Im very handy with Soldering but usally I build quadcopters lol so i dont know much about circuit boards.
Hope you can help!
Manuel Smeets it means you have 5v standby power. But your not getting 12v. So. Something on the board is blown/faulty. Follow along with my videos. Most power supplies are pretty much the same.
Same issue with my ps4, it wont turn by power button but it beeps by disc eject, it sounds but after 3 beeps it wont beef anymore...
hi, nice video. may I ask what is the fuse amp rating of that psu? I searched the internet and it says 5ah but mine says it is 4ah. also what would happen if I replace a 4ah fuse with a 5ah? any help would be great thanks
I have a shorted Zener Diode (ZD39), does anyone know the part number on that? Where can i get my hands on schematic or list of part?
hello, did you find the reference for diode ZD39?
Wow , i love your work mate...😊😊🎮🎮🎮
what is the voltage of the ZD 39?
Hey
I have the same power supply but my PS4 would turn off randomly. Have confirmed that it's the supply because I ran it off of an ATX supply and it worked. Can you tell what could be an issue??
Intermittent issues are the worst. Get a new one.
@@RepairLegion sad
Are they the same Wattage rating?
Working man ❤❤❤❤❤
psu most common in no power bc of bugs inside it
this resistor is a fusible resistor, replace it with the same type or next time you won't be so luck to have such an easy one to repair.
Ya 0.16.
Hi My ps4 is auto booting to safe mode and menu option not showing error is giving (su-34311-2) SCE_UPDATER_CORE_ERROR_SATABR_FW_GENERAL. Kindly please help if any solution
Srinivas Yalangi is try to initialize and reinstall the os
@@RepairLegion Thanks for you're reply but i tried that also safe mode menu option not showing
I am working on one of these which has 5V output, but no 12V, It was causing the Blue light of death. I purchased a replacement PSU and the PS4 works fine now, but I kept the faulty one to repair. I have faults with Q101 and Q102. They say 9990G1 on them. For the life of me I cannot find them to buy or even a alternative mosfet to fit and try. So frustrating when you find the faults but not the spares to fix. :) Any ideas on what exactly Q101 & Q102 can be replaced with. They are identical?
So I ended up finding correct parts for Q101 and Q102 on Ali Express. Still didn't work. No 12v output. With no visible signs of damage, or defect there was little to go on.
The 5v output rail working, so I ruled out a lot of primary side issues on the 5V side of things. So I went a littler further back on the 12V side of things and replaced the two surfaced mount transistor IC.
Still didn't work.
I was about to bin the board, when I decided to short the 5V+ supply rail to the standby pin which WAS NOT pins 1 and 4 on my board on output connector. It was pin 1 and 3 as far as I can remember, or possible 2 and 4. Lets just say it says it on the board which is 5Ve and Standby pins. After shorting the 5V+ rail to standby pin I got 12 Volts switched output. So I have managed to fix it I think. Either that, or there is a switching fault.
I had ordered a new one for my sons PS4 ages ago which fixed the original fault PS4 blinking blue light fault due to no 12V. My guess is that the Q101 and Q102. did fix it, but there is also a possibility that the 2 x surface mounted IC's fixed it on the primary side of the 12V rail transformer.
Did you really Read 9990?
Which resistor
Buenas tardes que valor tiene esa resistencia?? Me han traido una consola que no enciende y tiene los mismos sintomas!! Gracias!!
ahi dice que es de 16.2 ohm a 1/2 w pero no consigo encontrarla por medios normales
@@xanadusanson621 de 15 también valen
@@josemariacastillolopez5122 Gracias amigo!, compré hace poco una resistencia de 14ohm a 1/2 watio pero al probarlo quemó el mosfet que esta junto y la resistencia :( la verdad no se que sera. intentaré con uno de 15 ohm y le pondre un mosfet nuevo, solo que tardara porque lo pedí por alliexpress. (tengo dos fuentes del mismo modelo ADP200ER y las dos tienen fallas) :(
Amigo José Maria castillo López, entré al grupo de FB de este canal, presenté este problema y al parecer no era de 16.2 ohm sino de 0.16 ohms, la verdad no me siento muy seguro, en el video no distingo muy bien los colores pero sé que son de 5 bandas veré mejor, si tienes más info me lo haces saber por favor 👍✌️
@@xanadusanson621 pasame tu email y te mando una foto de las que pedí,eran de 0.15 ,en el foro de fb hay una publicación mia donde me contestes el autor de este video!!
what is that pistol?
William Ramirez desoldering iron
Hi there, can I buy 18 ohm or have to be 16.8ohm.
Regards
Hi ! I went to a parts store and they only had resistor 18 ohm and 0.5W. It worked!
@@PedroAntunes78 I used an 18 ohm one but it got burnt instantly, i suppose i have to get one with higher wattage right?
Grazie ho risolto👏💪
10j 1kv ceramic capacitor same value
Donde puedo conseguir la res 16.2 OHM 1/2 W
yo tampoco la puedo encontrar
good job!
Gracias
Sip
Basicamente que fue lo que hizo?
oye amigo , donde venden ese vaor de resistencia no lo he podido encontrar por internet andan de otros valores