For Tips, steps and Advice to start a train: 1st, Press "DELETE" key for the key to enter the Master switch and enable the control switch . 2nd, press "Pg Dn" "PgUp" to set the Master Control switch to modes , to diver the train, set it to "Full Speed Manual". If Brake testing is required, switch the Master Key to INTER, then after Brake testing, switch Master Control switch mode back to "Full Speed Manual". 3. Press "0" to enter. "Sign on" is "MANDATORY", then press "0" again to select the sections. Press "9" to move forwards or press "8" to go backwards. The destinations codes are from 31-53. 039 is the code your looking for when going to West Hampstead. After Signing in, press 0 to enter and confirm. Exterior Angles, press F2/F3. Use the Nun section to see through the trains and go up and down F5/F6 are the passengers doors. F5 for the left side and F6 for the right side. When Driving, put your mode to "Full Speed Manual". Do NOT put it in "FORWARD" because it restricted manual and you cant go above 8-10mph which the alarm goes off. Go to B3 first, press the "SPACEBAR" To turn the TBC and press Z to accelerate in terms to go to P3 Q is for your brake. Try to obey speed limits as you can. Aim at the green when you arrive at a station, there is a bar on your right side to help you, aim at the blue or preferably in the middle to be accurate. An "Accurate stop" light will lit, you are able to open the doors Hope these steps help you on BVE. Will speak about this in more detail soon with an live stream.
@@melonwhoexists8524if your not on P3, Full brake. press "Q" untill you get to P3. Once you reached P3, press the spacebar once for the handle to turn 90 degress towards you. Then press "Z" to go to b3 full speed motor
For Tips, steps and Advice to start a train:
1st, Press "DELETE" key for the key to enter the Master switch and enable the control switch .
2nd, press "Pg Dn" "PgUp" to set the Master Control switch to modes , to diver the train, set it to "Full Speed Manual". If Brake testing is required, switch the Master Key to INTER, then after Brake testing, switch Master Control switch mode back to "Full Speed Manual".
3. Press "0" to enter. "Sign on" is "MANDATORY", then press "0" again to select the sections. Press "9" to move forwards or press "8" to go backwards.
The destinations codes are from 31-53. 039 is the code your looking for when going to West Hampstead.
After Signing in, press 0 to enter and confirm.
Exterior Angles, press F2/F3. Use the Nun section to see through the trains and go up and down
F5/F6 are the passengers doors. F5 for the left side and F6 for the right side.
When Driving, put your mode to "Full Speed Manual". Do NOT put it in "FORWARD" because it restricted manual and you cant go above 8-10mph which the alarm goes off.
Go to B3 first, press the "SPACEBAR" To turn the TBC and press Z to accelerate in terms to go to P3
Q is for your brake.
Try to obey speed limits as you can.
Aim at the green when you arrive at a station, there is a bar on your right side to help you, aim at the blue or preferably in the middle to be accurate. An "Accurate stop" light will lit, you are able to open the doors
Hope these steps help you on BVE.
Will speak about this in more detail soon with an live stream.
@Jubilee Di how do I actually put it to B3?
@@melonwhoexists8524 03:00
@@melonwhoexists8524if your not on P3, Full brake. press "Q" untill you get to P3.
Once you reached P3, press the spacebar once for the handle to turn 90 degress towards you.
Then press "Z" to go to b3 full speed motor
@@JubileeDi Thank you. Also, do you know how I get my auto-announcements to turn on?
@@melonwhoexists8524 on your TMS system.
Go down to Comms. CONTROL and press enable all messages something like that
When i press delete still nothing happens
When I load up the route what sounds like an alarm is going off in the drivers cab and nothing I pressed would turn it off, can someone help me?
Press 0 to acknowledge the alarm. It could be because you need to turn the dead man's handle depending on the situation
@@JubileeDi tried pressing 0 but it didn't seem to do anything, I'll try the dead man's handle
@@JubileeDi the guide doesn't use "dead mans handle" to refer to anything, what is the deadmans handle?
I have a question, Which version of open BVE is 32 bit? because for me it says i need to reset open bve on the screen thing in the train
Awesome video!
Thank you, hope this helps you. Will make a full video of it live stream
Mine say error not found please reset openbve
Try and download open bve (32-bit)
@@JubileeDihow do you download 32 bit
How do I activate the PSD? (Platform Screen Doors)
please help it doesnt work
Try and download open bve (32-bit)
@@JubileeDi it works on central line tho
@@orig1nalfn91 do try and re download it to open bve (32-bit). Hopefully it will work
@@orig1nalfn91 it works on my computer. I mean do you have like PC?
@@JubileeDi ye but it don’t matter anymore I don’t have a monitor anymore
Good stuff 😉
Thanks bro👍
Also, edited the description with codes of destinations added so that people can see properly.
@@JubileeDi For some reason i do pgdn and pgup it does not work ..
@@mansoor1075 yeah
What is b3
Life saver!
if I press delete nothing happens
Try connecting the keyboard to your computer
what game is this
OpenBVE Western Region
Can you please get in contact with me with like discord or smth because it wont work and it hasnt worked for years
when i click delete is doesnt do anything
Try connecting the keyboard to your computer
Just seen your message now
@@JubileeDi i connected the keyboard to my laptop its not working when i press delete or del.