Neo-Tec NS892 (stihl ms660 clone) REVIEW!!
Вставка
- Опубліковано 25 лип 2024
- Neo-Tec ns892 chainsaw review stihl ms660 clone. Will this thing hold up??
NEO-TEC Gas ChainSaw NS892 for G660 2-Cycle Power Head 92cc 25/30/36" Power Chain Saw 5.2KW 6.4HP Petrol Chainsaw for Big Wood Cutting All Parts Compatible to MS660 066 Magnum Chainsaw Without Bar a.co/d/cwXMo6I
![Lp. Последняя Реальность #107 РОДНОЙ ДОМ [Финал] • Майнкрафт](http://i.ytimg.com/vi/IK3QKzKUlHM/mqdefault.jpg)
My experience pretty much mirrors yours. Easiest to start , of any of the saws I own. Am running the 32 and 36 inch bars it pulls them well. Going on my third year now still running strong. Only failure so far was a clutch spring. Local Stihl dealer got me the new parts. Like you I prefer the 60-70 cc saws, for most work. But the NS892 fills the requirement for a bigger saw.
I have the Holzfforma G660, pretty much same saw, got mine off Amazon also, but came to $427 or something, came with 3 chains, 25 inch bar, mixing jug for 2 stoke & gas, I had problems the 2nd day using it, the pull start pawls we’re making awful noise, got new & been great since then, good video
I got two 892bv’s. Very nice bog bore saws.
3:35 that is a piston ring compressor as is the other two like it in the bag, not sure why they'd give you those though.
I have the same saw. It pulls a 42 in bar with no problem at all. I use mine on an alaskan sawmill.
Awesome I don’t doubt that one bit! thanks for watching!
Hello from northern Canada :) well it definitaly has no problem with a 20" bar that's for sure, and it sounds like a stihl,
Once you go through 5-8
Tank fills you will see the saw will run even better!
Ignore or ban the internet safety police. We don't need those kind of people putting negativity in our lives!
I got that saw w 36 bar the chain had busted side link I fixed I only ran it with 24 bar it's a real good running saw
I would not use an airfilter like that because it will clog quickly and starve the saw of air. You chips will be larger with more fine dust on the larger chains. The stihl filter for the 660 fits better, more air tight and is easily cleaned with air. I have seen more than one saw with saw oil soaked dust packed in the piston base. On all these 660 clones replace your pawls and the pull starter with the stihl version, replacing the spring while your at it. That will likely keep you cutting. I got a whole list of upgrades
Most saw shops don't sell parts for discontinued saws unless they have parts saws
Does anyone know if Stihl/Zama carbs are an exact swap. Concerned about linkages. Throttle/Choke/Kill switch.
same as for hultzforrma saws
Can of dip saved my leg once
how is it now?
Still doing good. I don’t use it very much but it’s one heck of a saw. I had developed a gas leak that I haven’t had time to investigate though
That foam air filter is better than what Stihl uses. But you have to use air filter oil on it for it to work.
I have noticed most of these saws that come with work gloves, the gloves seem to be sized for Chinese girls, I wear XXl gloves and theirs barley fit my little finger. LOL
Some real knowledge would be an improvement.
Great review Andy. I'm guilty of not wearing all the safety gear either. I sent you a message on Instagram.
Thanks for watching! Yea I probably should start but I’ve been lucky so far
what the story is hultzforrma/neo tech bought the patten for the stihl husquvana saws
Yea I was told they bought the patent on them since they are all discontinued saws in the husqvarna and stihl line up
A wannabe stihl!!! Not for me!!!
Nobody cares that you don’t want one.