Hi..very nice of you, to explain in details. I have a 2007 western star , Detroit 14L. It’s cranking well but won’t start and voltage gauge always shows 0. It’s been sitting for few weeks in cold weather, can be the ECU faulty? If yes how much to reman, such a unit? Thx much .
Hello brother, how are you? I am from Honduras and I have a problem with a computer on my truck, the truck turns off but it remains on, the fault only lasts a second, how can I communicate with you. Greetings
If I said its 3.7 and you soldered in a 3.7 volt battery in your ddec iv and caused damage would you blame yourself or would you blame me? We both know the answer to that question.
I don't. The school of hard knocks is expensive and time consuming. Guys that know this stuff aren't big on teaching it and making more competitors for themselves.
As far as drivability usually nothing. Most will run and fire injectors even after you take out the battery. If your DDEC doesn't start it's not a battery issue.
Well, sometimes that battery leaks acid allover and causes corrosion and deterioration in part of the circuit board. It can lead to a failure in the ECM and inability to communicate with truck. Happened to my DDEC V.
Since I got back from MATS in Louisville I have been getting more and more requests like yours. Once I get done building my N14 Celect, Celect Plus, DDEC V, ISX CM570, ISX EGR CM870, and ISX EGR DFP CM871, upgrades then maybe I'll be able to build a testing simulator for another company or more likely I'd sell them one of my old retired ones. Also guys call me and want to buy batteries from me or want to find out where I am getting them. I'll admit when I first started changing the batteries in these I thought it would be easy too until I found out the hard way that these batteries don't always fail of natural causes. Sometimes the battery was killed by a board short to case ground for a 12 volt supply trace. So guess what happens when you solder a fully charged lithium battery to a shorted RTC circuit. You get a fire. Or if your lucky lots of acid all over the board. Your first thought might be to take it out on the guy who sold you that battery. That guy isn't going to be me. If by chance you believe a dead RTC battery is causing your DDEC not to start. Look elsewhere. A dead RTC battery will never prevent a DDEC from starting the engine unless the battery burned the board or leaked acid on the board.
What else cause dead rtc battery? Is there any connection with gauges (oli pressure ,oil temp,coolant going all the way up 250f? Check engine coming on and off, Codes : ENG. throttle pedal Short lo. 128 091 04 ENG Low. 128s232. 01 Acceleration pedal not working. Engine starts every time and works perfectly on the spot ( idling). Sometimes I could drive 700 miles normally and suddenly check engine comes on and loosing acceleration pedal but keeps idling?! Engine out frame rebuild two months ago,everything is new 35000$ repair costs. Detroit ddes 4 12.7 1999 Thank you 🙏
18 different software versions that are not compatible and 4 different hardware versions make that lots of work and require lots of testing to validate. If it was easy everyone would be doing it. You could always send the DDECs to me and I could get it done.
Hi, I am very interested in taking courses in ECM repair, calibration, test benches, and I would like to know if you give them or who can help me and are online or in person, I am very interested, I hope your answer thanks
hello . I have a question about whether the engine starter battery is removed for a period of time. Does this affect the ECM software?
Hi..very nice of you, to explain in details. I have a 2007 western star , Detroit 14L. It’s cranking well but won’t start and voltage gauge always shows 0. It’s been sitting for few weeks in cold weather, can be the ECU faulty? If yes how much to reman, such a unit? Thx much .
Heat the computer with a hair dryer and it will start
You get OEM batteries from the OEM. It also helps if you buy in bulk like I do and are a dealer.
We're I can buy the battery? Please
mtu series 60 for marine i am getting a code 332 J 1708 Data Link Loss can you give me some helpful info where to look
Hi was interested in getting a quote on deteoit comp with orofinal settings where's your shop located thank you
Hi I have a det v pod not working any clue please let me know thanks
What are the most common failure in ddc3 with code 52 and with engine not starting??
Timing reference sensor issues. Most of the time it's in the wiring.
Have you think at give some course in a future?
What size and type bolt is on the ecm cover of a Ddec3 ecm @diesel control service
Hello brother, how are you? I am from Honduras and I have a problem with a computer on my truck, the truck turns off but it remains on, the fault only lasts a second, how can I communicate with you. Greetings
12 point
What up with sum new videos?
Where you find battery
What is the battery voltage?
3.7 volt ??
If I said its 3.7 and you soldered in a 3.7 volt battery in your ddec iv and caused damage would you blame yourself or would you blame me? We both know the answer to that question.
How is the ecm battery/DDEC IV life measure? I mean per hours or years.
Both
Do you know where or what company gives courses about that on line?
I don't. The school of hard knocks is expensive and time consuming. Guys that know this stuff aren't big on teaching it and making more competitors for themselves.
can you sell me dump file for a eproom for ddec4 detroit 60 series whit code problem 253 memory fault?
If battery dead what happened to ecm
As far as drivability usually nothing. Most will run and fire injectors even after you take out the battery. If your DDEC doesn't start it's not a battery issue.
Well, sometimes that battery leaks acid allover and causes corrosion and deterioration in part of the circuit board. It can lead to a failure in the ECM and inability to communicate with truck. Happened to my DDEC V.
What’s the purpose in replacing the ecm battery if the DDEC can run without its battery?
What does a ddec 3 ecm run for a battery?
No battery in a DDEC III
Since I got back from MATS in Louisville I have been getting more and more requests like yours. Once I get done building my N14 Celect, Celect Plus, DDEC V, ISX CM570, ISX EGR CM870, and ISX EGR DFP CM871, upgrades then maybe I'll be able to build a testing simulator for another company or more likely I'd sell them one of my old retired ones. Also guys call me and want to buy batteries from me or want to find out where I am getting them. I'll admit when I first started changing the batteries in these I thought it would be easy too until I found out the hard way that these batteries don't always fail of natural causes. Sometimes the battery was killed by a board short to case ground for a 12 volt supply trace. So guess what happens when you solder a fully charged lithium battery to a shorted RTC circuit. You get a fire. Or if your lucky lots of acid all over the board. Your first thought might be to take it out on the guy who sold you that battery. That guy isn't going to be me. If by chance you believe a dead RTC battery is causing your DDEC not to start. Look elsewhere. A dead RTC battery will never prevent a DDEC from starting the engine unless the battery burned the board or leaked acid on the board.
do you sell them?
or where do i find them?
What else cause dead rtc battery?
Is there any connection with gauges (oli pressure ,oil temp,coolant going all the way up 250f?
Check engine coming on and off,
Codes :
ENG. throttle pedal
Short lo. 128 091 04
ENG
Low. 128s232. 01
Acceleration pedal not working.
Engine starts every time and works perfectly on the spot ( idling).
Sometimes I could drive 700 miles normally and suddenly check engine comes on and loosing acceleration pedal but keeps idling?!
Engine out frame rebuild two months ago,everything is new 35000$ repair costs.
Detroit ddes 4 12.7 1999
Thank you 🙏
How tranfer ecm files to another ecm .detroit dd4
18 different software versions that are not compatible and 4 different hardware versions make that lots of work and require lots of testing to validate. If it was easy everyone would be doing it. You could always send the DDECs to me and I could get it done.
Hi, I am very interested in taking courses in ECM repair, calibration, test benches, and I would like to know if you give them or who can help me and are online or in person, I am very interested, I hope your answer thanks
I'm not doing any training courses at this time.
Is there a battery in DDEC III?
No battery in a DDEC III.
Buenas soi de panama si me puede ayudar cual cable de itnition y cable de aceleracion de ditroi serie 60 dd4 motor era cat haora boi poner ditroi
The ignition input is pin B3 on the OEM side 30 pin connector.
3.5 v unstoppable naw needs more voltage ⚡ rheostat potential meter coil remember the old ecm 1994 lower
Hi. Not worth to.... Left message 2 weeks ago. No replay yet,,, Think first.
this guy never answers his phone or returns messages
Especially during the holidays. I don't spend lots of time on the phone when I've got jobs sitting on my workbench and trucks that are down.
phone #