How to control Multiple Motors with One VFD ?

[@cheyguvera9680]

My favourite channel for automation, thank you so much

[@EASYPLCTRAINING]

thank you for the appreciation of my hard work

[@cheyguvera9680]

@@EASYPLCTRAINING i have one doubt brother, all motors rpm should be same ? I mean synchronous speed which is on motor name plate

[@EASYPLCTRAINING]

Same kw and same rpm, its better for safe operation. All three motors should be identical to keep the current balanced.

[@datsim_labelle1762]

Hello, nice video and explanation!
I have a 2post car lift with 2 motors on it (one each side). Both use the same RPM and specs and are already connected together. My question is, using one VFD with the correct spec for example, both motor together are 5.5KW if I use one VFD with an output of 7,5KW that will be enough and safe for operating it ? Those motor are 220V 3PH and my shop only have single phase 220V. With the VFD I’ll be able to convert single to 3phases and make both motor turning without any problem ??
Thank you for your help
Simon

[@krzysztofkapcia4521]

Your animations are incredibly useful in my job. Thank you very much for your effort in creating them.
Can I ask what software do you use to create these presentations?

[@EASYPLCTRAINING]

Blender 3.2

[@burhanahmad9095]

Hello sir..im going to connect VSD to 30 induction motors 3kw..can you give an advice ??thank you very much

[@oll4820]

Is there a way to control multiple motors with just 1 VFD without running them simultaneously? I want one motor to run at a time then set the others as backup.

[@lawalrafiu151]

Thank you for this session.
I would like to ask if there is a way we can connect a VFD to a single phase motor.
If anything of such is possible?

[@EASYPLCTRAINING]

No dear , for single phase motor you can use speed control cards , these are basically voltage regulators

[@lawalrafiu151]

@@EASYPLCTRAINING thank you so much. I appreciate it.

[@prakashelectricals5581]

I have used two motors in single vfd, without using any MPCB
MEAS direct wiring
What can be problem comes in future?

[@EASYPLCTRAINING]

See the last part of video

[@roshan2940]

Sir, Which software you used to create such type of videos and animation

[@EASYPLCTRAINING]

I used blender 3.1

[@kouassirobertkodo6754]

Thanks a lot.
What the setting of the current?

[@EASYPLCTRAINING]

Vfd current rating must be more than the motors

[@theniii]

that "goodbye" at the end tho.

[@linossinkala7840]

Thankyou sir ,i appreciate your vidoes

[@AhmedAli-rz8sf]

Thank you so much it's so clear

[@agent70vids3]

I have a problem in my altivar38 VFD, before its running two motors at the same time, when we replace the card of vfd, it cannot run the two motors at the same time, you need to run one motor, once it reaches the setpoint speed,that is the time you will run the another motor. What is missing?

[@EASYPLCTRAINING]

You replace the control card of the vfd or power card ?

[@agent70vids3]

@@EASYPLCTRAINING i replace the whole vfd now, It's the same model. I need to run the first motor, once it reaches the set point speed, i can run the another motor. Before they are starting and running at the same time. What is missing?

[@oll4820]

@@agent70vids3 How did you do that? I needed that setup where one motor only runs at a time, then set the others as back up.

[@rezabahmaninia2571]

Hello.what software desian vdiuo????

[@EASYPLCTRAINING]

Blender

[@AnasAl-Dhafiri]

Thank you very much sir

[@EASYPLCTRAINING]

You are most welcome dear

[@goowatch]

What happens if one or more of the MBPCs are automatically activated for protection?

[@EASYPLCTRAINING]

Nothing will happen,,,,, other motors will keep on running,

[@EASYPLCTRAINING]

May be vfd trips , with over voltage alarm

[@PankajSingh-xs1mw]

एक भी डी एफ से तीन मोटर चलाना सीखे साथ हीं जाने कितने एम्पियर का लेना होगा

[@alibakhshayeshi1839]

❤❤❤

[@kiranchoudhari4717]

Please mention your insta Id