Megane 2 sloppy gearbox leaver fix this works on ND0 gearbox found on megane 2 1.9dci, megane 225, megane r26, megane f1, but might work on others as well.
I managed to survive more than 2 years with broken bushing with this trick. I had to push it back onto the sphere like 10 times during this time, and when it popped out selecting 5th and 6th gear became very difficult. I bought a complete used control box eventually, but it turned out I was sold a right-hand drive unit which was completely different, so I had to replace the bushing only. This is such a simple little part and I have not managed to find it as new. Replacing and disassembling the control box is not as painful as I initially believed, so I recommend doing it instead of living with this problem.
Irmao meu megane sedan 2008 1.6 16 valvulas sedan. Meu carro estava marcha querendo ficar pesada e guando cheguei em casa e fui estacionar de re ela sai toda marcha nao entra nehuma, carro nao sai do lugar ne. Apertando embreagem. La frente os cabos estao tudo ok apertados .. vc consegue da um diagnostico..pq creio problema seja ali dentro cabo marcha.. fico grato se conseguir me responder. Muito obgdo
Moj se krece levo desno cca 2-3 cm a kad sam se vozio kroz sumu gde je put pun kamenja, popravio se sam, a sad je isto kao pre. Da li ce mi ovo pomoci ili je mozda ona bela plastika pukla?
I’m just trying to work out if this is my issue and how this causes the side to side stop. Would you notice this problem all of a sudden or would it get worse over time? Thanks
Hi, My gearstick had this same symptom, but while driving my gearstick became so loose left-right, and I realised I only had 3rd and 4th gear available, so I limped home without stopping... Navigated the traffic lights, etc... I tried this, but something else is wrong I think, something looks jammed when I look through the hole I drilled...
Hello, i had a problem today, the 6th gear jumps when i hit the gas , when im not accelerating it stays ok, but once i accelerate it jumps, only 6th gear .. would this fix it?
Would this fix work if the gear leaver gets super stiff and barely changes the gears? Got to a point where you have to use a lot of force to change the gears, feel like it's stuck in strong clay
What if the plastic bush at 4:14 is broken? i drilled a whole and saw the bush is broken. How do you fix this one?? can you explain a bit please? or how to pull out this mechanism?
That is strange. We dont have Captions enabled. Are you sure your language is not set incorrectly on YT? Anyway ask what do you mean and Ill do my best to answer it :)
Milose, molim te, hoces li detaljnije reci, dakle saltac ne moram vaditi iz auta, probusim rupu i sta je procedura? Samo gurnuti plastiku unutra? To je sve? Hvala unapred
@@EngineeringSiblings Hvala puno! A kako se vadi saltac? Da li moze kad se skine konzola ili auto mora ici na dizalicu, da se skine auspuh, zastitni limovi itd?
Probao danas na mome meganu 2 1.6 16v.Menjac je sad kao iz fabrike!!! Hvala Milose
I´ve tried this solution today on Megane 2 CC 2.0 - works amazing. Like a new! Thank you
I managed to survive more than 2 years with broken bushing with this trick. I had to push it back onto the sphere like 10 times during this time, and when it popped out selecting 5th and 6th gear became very difficult.
I bought a complete used control box eventually, but it turned out I was sold a right-hand drive unit which was completely different, so I had to replace the bushing only. This is such a simple little part and I have not managed to find it as new. Replacing and disassembling the control box is not as painful as I initially believed, so I recommend doing it instead of living with this problem.
For me, it didn't pop of for a long time, when it did the second time I made a sleeve that I pressed in. there was nothing to "pop" anymore :)
I drilled little bit too high and only had access to upper part of the white bearing but I could press it in and it worked like a charm! Thank you!
Glad I could help :)
Irmao meu megane sedan 2008 1.6 16 valvulas sedan. Meu carro estava marcha querendo ficar pesada e guando cheguei em casa e fui estacionar de re ela sai toda marcha nao entra nehuma, carro nao sai do lugar ne. Apertando embreagem. La frente os cabos estao tudo ok apertados .. vc consegue da um diagnostico..pq creio problema seja ali dentro cabo marcha.. fico grato se conseguir me responder. Muito obgdo
Moj se krece levo desno cca 2-3 cm a kad sam se vozio kroz sumu gde je put pun kamenja, popravio se sam, a sad je isto kao pre. Da li ce mi ovo pomoci ili je mozda ona bela plastika pukla?
@@qoikon3704 lako moguce da je i kod vas taj problem koji sam ja prikazao na videu.
@@EngineeringSiblings probacu danas vas nacin
I’m just trying to work out if this is my issue and how this causes the side to side stop. Would you notice this problem all of a sudden or would it get worse over time?
Thanks
It suddenly falls off and than its this sloppy. If it happens slowly than its jus wear on the system
I have this problem too. When the engine is hot the gearbox gets stiff side to side
Hi, My gearstick had this same symptom, but while driving my gearstick became so loose left-right, and I realised I only had 3rd and 4th gear available, so I limped home without stopping... Navigated the traffic lights, etc... I tried this, but something else is wrong I think, something looks jammed when I look through the hole I drilled...
do you have an way to send a picture ?
It could be that your cable got detached (most likely) and than its much bigger work to take it off
Thank you!
Hello, i had a problem today, the 6th gear jumps when i hit the gas , when im not accelerating it stays ok, but once i accelerate it jumps, only 6th gear .. would this fix it?
Sadly most likely not. :(
Would this fix work if the gear leaver gets super stiff and barely changes the gears? Got to a point where you have to use a lot of force to change the gears, feel like it's stuck in strong clay
If you can switch gears with the engine off, it's the hydraulic clutch bearing or pressure plate.
Its the same operation if the gearbox os slopy in the front and back move?
Thanks Milos
What if the plastic bush at 4:14 is broken? i drilled a whole and saw the bush is broken. How do you fix this one?? can you explain a bit please? or how to pull out this mechanism?
I'd like to know about that too.
do u have a video for the automatic gear box?!
Could you explain why did you make that hole? Can't be opened without that hole? :-? :D
I know its late reply. I made the hole ao it can be repaired without taking it of the carr which is a much more demanding job than this
Remowe the fron plastic cower. The captions are in Russian?
That is strange. We dont have Captions enabled. Are you sure your language is not set incorrectly on YT?
Anyway ask what do you mean and Ill do my best to answer it :)
Milose, molim te, hoces li detaljnije reci, dakle saltac ne moram vaditi iz auta, probusim rupu i sta je procedura? Samo gurnuti plastiku unutra? To je sve? Hvala unapred
@@EngineeringSiblings Hvala puno! A kako se vadi saltac? Da li moze kad se skine konzola ili auto mora ici na dizalicu, da se skine auspuh, zastitni limovi itd?
Anyone know the thread size of the gear stick is it a m12?
OK ok I'm looking to get like an aftermarket gear knob and is the actual gear stick was threaded it would be easier you know
@@EngineeringSiblings I only have a 5 speed
Não existe reparo para esse problema
well, you just need to watch the video :) if the plastic is however completely worn, it can be replaced with a plastic "pipe" or hose