Great job mane on your bike! I have a question: I recently rebuild my engine and when I try to put bike in neutral it won't downshift past 4th gear. It's not the clutches so I wanted to know if you could lead in the right direction to fix this issue and hope I don't have to tear this motor apart again
Hey man so I have an 2008zx14 with a 63 inch wheelbase and I'm a bigger rider 6'8 275. So I my rear shock is bottoming out, any recommendations for a different spring to use? I really don't want to break the bank so I'm debating on swapping the spring.
Sorry about the issue brother. I know you take care of it. I had a question maybe you could help me with. My 07 replaced the clutch cup up top bleed the entire system on top and slave area. The clutch is nice and firm but it grabs at the very top. If I full throttle it clutch is normal dose not slip. Any Ideas? New clutch?
Hello, can u tell me what i neet to change? i have a gen 1 head and lower block is gen 2 (abs version) what shoul i can change ? sometimes starts but have a misfire an sometimes wont start, sparks are so black and unusefull fuel 😢 new sparks, new ignition coil, new zx10r injectors but still same, sometimes have a cam sensor error code
Great job mane on your bike! I have a question: I recently rebuild my engine and when I try to put bike in neutral it won't downshift past 4th gear. It's not the clutches so I wanted to know if you could lead in the right direction to fix this issue and hope I don't have to tear this motor apart again
Hey man so I have an 2008zx14 with a 63 inch wheelbase and I'm a bigger rider 6'8 275. So I my rear shock is bottoming out, any recommendations for a different spring to use? I really don't want to break the bank so I'm debating on swapping the spring.
Sorry about the issue brother. I know you take care of it. I had a question maybe you could help me with. My 07 replaced the clutch cup up top bleed the entire system on top and slave area. The clutch is nice and firm but it grabs at the very top. If I full throttle it clutch is normal dose not slip. Any Ideas? New clutch?
It's great to see the final results of your hard work and labor. Keep it up.🤙🏽
Clean build are you coming to KOG at galot in May ? Or Grudge Nationals in June i have a couple zx14’s I am bringing out this year
Im unsure at this point. Im haveing to switch my combo
@@DRKKNTRACING put her at 68 inches street hustler what I am running with my zx14 and true hand clutch killa with my other zx14 with nitrous
Im in hand clutch Killaz in Louisiana so changing my combo to run nitrous after this event
Hello, can u tell me what i neet to change? i have a gen 1 head and lower block is gen 2 (abs version) what shoul i can change ? sometimes starts but have a misfire an sometimes wont start, sparks are so black and unusefull fuel 😢 new sparks, new ignition coil, new zx10r injectors but still same, sometimes have a cam sensor error code
I bought the same front tire as you and cannot seat the bead to save my life. What was your technique? Thanks for your time.
I had too put assembly lube on the bead and wheel
@@DRKKNTRACING were you able to hit it with air after? Anytime I pump air into it, it doesn't take it. Thanks so much for the help.
@@bobbylabony4398 so put assembly lube or grease on the and wheel. That creates an temporary seal then it should take
@@DRKKNTRACING oh ok gotcha sounds good. Should I do both sides I'm assuming and then try the air?
Yea I did
Great videos. Keep them coming !
Unfortunately the videos are done for now. Had a turn of events the impacted negatively. I will eventually make a video exsplaning.
@@DRKKNTRACING sorry to hear. Thank you for what you have done so far.
Where you getting your titanium oil pan bolts at and what size are they ?
How's the fuel regulator and pump relocation working
Im very pleased with the setup. Ive had zero issues with it.
Hell yeah Zach
Great job bro it looks good love those rims
I appreciate it
@DRK KNT RACING yep good job.
Hey where you get the holes in the subframe from?
I cut them out with an metal hole saw bit