Excelente video tengo esta maquina y están de poner algunas cosas a punto sobre todo la bobina esta algo de centrado porque al bajar la aguja esta golpeando la bobina y quiero corregir talves tiene un video relacionado con ese detalle ?....también sería magnífico obtener el manual como lo ago ?
Acabo de comprar una453 y no tiene la banda interna al jirarala con la mano el tira hilo golpea en la parte de abajo Tampoco se como va el que levanta el pie con la rodilla. Le agradesco si me puede ayudar
There is nothing simple when it comes to this machine. I never tried to remove the oil tank only. There are two screws that have to be removed. The one on the oil tank, and there's a screw on the side below the hand wheel. This screw holds a clamp for one of the tubes. You remove those two screws the tank should pull out enough to where you can gain access to the back to pull off the tubes. Take you time on working with the oil tank. It's only plastic and breaks easily.
Hi Stephen, very informative video. I just bought exactly this same machine. It's in pretty good condition to be honest but as with yours the sump gasket plate sponge has deteriorated to mush. I've looked at replacements online but can't find any. You spoke of a magnet but if going down that route how do the cogs get lubed. Your help would be much appreciated🙏
HI THERE IM A RETIRED INDUSTRIAL SEWING MACHINE MECHANIC I CAN TELL YOU THAT THE CAM YOUR NOT SURE ABOUT IS IN FACT IT OPERATES A KNIFE MECHANISM WHICH LOOKS AS IF ITS BEEN TAKEN OFF, IF THE 463 HAS 900 AFTER IT THEN ITS A UNDERBED TRIMMER I WOULDNT GO WITHOUT THE SPUNG IT COLLECTS EXCESS OIL
Thank you, I have been trying for years to find out what that cam was for. In another video, another mechanic told me about the bracket that pivots around the bobbin housing is where the knife blade was mounted, it make sense now that bracket was operated by that cam.
Assim como em todas as máquinas de costura industriais, você deve remover o rolamento do eixo principal, removendo primeiro o volante. Com a roda removida, o rolamento deve sair facilmente. Não remova o anel elástico do rolamento. Você pode ter que usar algo como óleo diesel para dissolver o óleo seco entre o rolamento e a máquina.
Hola buenas tardes, tengo una maquina 563 Pfaff, vi como devanaste el hilo del carrete, pero el problema es que cuando oprimo el pedal se mueve la aguja, que tengo que hacer para que la aguja de la maquina no se mueva cuando estoy devanando el carrete. Otra cosa donde conseguir la cartilla de manejo de la maquina. No se como se engrasa ni otras funciones que requiero aprender. gracias.
No puede, el Pfaff 563 no se desconecta del volante a la aguja, por lo que el volante gira y la aguja sube y baja. Ahora mi respuesta depende de si Google tradujo correctamente su pregunta.
Hi, I have the same machine with the thread cutter, I wanted to ask you something, when I push the fabric back with the lever sometimes the thread breaks, what can it depend on?
@@gmcxm211 thanks for the answer, but why do you think that the problem when the fabric backs off the thread is broken is due to the fact that the thread cutter is present? excuse for my english
take a video camera and try to find a way to mount it to where you can take a video where the bobbin is at. Then you might see what the thread cutter is doing. Or have someone sewing while you sit under the table and then you can watch it for yourself
Hi, I have pfaff 260. can you disassemble and reassemble, pfaff 260 in video? I have a problem the zigzag doesn't engage, It will sew straight and the cam mechanism has no problem. I think a spring is missing. I would appreciate if you can do that. Thanks.
@@evelynsia460 good news is if it can sew straight stitches it's properly timed. I don't have a 260, just a 360 and there some differences between the two. now if you select a decretive stitch and the middle knob/level moves in one direction only, while sewing try gently to move the knob/level back. If there is no resistance then yes you do have a spring missing. If there any resistance than it just needs to be cleaned. The only problem with these machines, the decretive stitching isn't all that "crisp" as it is with the electronic sewing machines. Since these are all cams and spring regulated the needle never returns to a true zero. There will always be a thread size gap or off a width of a needle in some places. We're talking Model "T" Fords here compared to our computer controlled cars of today.
Hello. The plastic gear must not be replaced with a metal one ( ua-cam.com/video/Cfi0aKLPQF4/v-deo.html ). If the hook of the sewing machine gets stuck, then the plastic gear is a safeguard against the big problem. The gear will break and not cause much damage to the sewing machine. This gear is located just after the main shaft and transfers rotation to the hook of the sewing machine. Therefore, you cannot install a metal gear.
So, this was design to be a “safety fuse” and not just to make the machine run quieter? I can see that. Has there ever been a situation where the hook jammed to where it stripped out the teeth of the nylon gear? I was sewing along and the thread got tangled up in the hook. The belt slipped on the hand wheel. Now I wasn’t using a clutch motor also my belt tension isn’t all that tight because I don’t want to wear out the bearings
@@gmcxm211 A side function of the plastic gear is a little less noise. But it is plastic because it is a fuse. There is no problem to put a metal one, and the adjacent gear is just that. Repairing with a metal gear when the shuttle is jammed can be expensive. The hook of the sewing machine may break. The motor may be damaged unless the overcurrent protection is activated. In addition, the small gear may be damaged from fragments. The timing belt may break. There can be many problems. If the plastic gear breaks, the shaft continues to turn and the shuttle does not turn. Therefore, there is no major damage. You are a good mechanic! A lot of work has been done.
Hallo, I have just found this machine and thinking to buy it. But the question raised: does it need an air compressor? The seller says it does. Can you answer me please:) Thank you.
it probably does if it has a thread cutter or any other special operation. Now, for it just to sew, no it doesn't need air for that. but if it does have those features you can get an air compressor pretty cheap at harbor freight. Besides once you have an air co presser you'd be surprised how handy these things are
Hola Compré una, pero me doy cuenta que le cantan piezas y no sé dónde adquirlas Aparte de que no sé si solo son esas piezas que le faltan o hay más Me podrías apoyar?
@@arelybruno7600 Buenas tardes, en pfaff hay originales calle de vainilla en granjas México, el número no recuerdo, Mándame tu gmail y una foto con modelo y tal vez te consiga refacciones, En cdmx, ¿ Cuánto pagó y en donde? Ok gracias.
remove the back panel then go to 10:30 in the video. move the knee lifter, the cam with the 2 screws should also move. if it does remove the front cover then go to 20:10 in the video and insure both hooks capture that bar you see.
What bobbins does it use. I just bought this machine for $160 but the girl could not find book or drawer with the spare parts but she’s gonna look later but for $160 for head n table with motor who’s complaining. LOL
Just bought one! Mindblown from dicovering this series😄 Thanks!
Im from Brazil, and like very much your job! I need to fix my machine, and you help me witth my problem. Thank you!
Excelente video tengo esta maquina y están de poner algunas cosas a punto sobre todo la bobina esta algo de centrado porque al bajar la aguja esta golpeando la bobina y quiero corregir talves tiene un video relacionado con ese detalle ?....también sería magnífico obtener el manual como lo ago ?
Hello - thanks for posting this. Mine has the same problem --- where did you source the bearings?
Coloco o óleo na minha máquina, e vaza tudo... O que posso estar fazendo de errado? Aguardo ansiosamente por resposta. Obrigada! Xoxo
Hola buen video me gustaría ver el final para ver cómo se cambia el fuelle o resorte para accionar el empuje que deja libre el tira hilo. Gracias
Excelente video. Lo podrían traducir a español? Gracias
Boa noite! Essa maquina usa agulha cabo fino ou cabo grosso
Acabo de comprar una453 y no tiene la banda interna al jirarala con la mano el tira hilo golpea en la parte de abajo
Tampoco se como va el que levanta el pie con la rodilla.
Le agradesco si me puede ayudar
Hola Stephen,
How to change toothed belt for buttonhole pfaff 3116?
Thank you
merci pour la védeo si inteéssante svp vous avez une une maniére simple de changer le reservoir a huilie merci
There is nothing simple when it comes to this machine. I never tried to remove the oil tank only. There are two screws that have to be removed. The one on the oil tank, and there's a screw on the side below the hand wheel. This screw holds a clamp for one of the tubes. You remove those two screws the tank should pull out enough to where you can gain access to the back to pull off the tubes. Take you time on working with the oil tank. It's only plastic and breaks easily.
Como se saca el buje del pue prensatela
Poderia traduzir para português Brasil?
Hola
Yo tengo una
Es la primera ves que compro una
Y no sé cómo armarla
O como saber que piezas le faltan gustaría que me dijera como hacerle
Boa tarde, estou precisando do reservatório de óleo que fica na frente da máquina PFAFF, vcs tem para vender?
Hi Stephen, very informative video. I just bought exactly this same machine. It's in pretty good condition to be honest but as with yours the sump gasket plate sponge has deteriorated to mush. I've looked at replacements online but can't find any. You spoke of a magnet but if going down that route how do the cogs get lubed. Your help would be much appreciated🙏
I say exactly. It's a 463 but the gasket plate is not same shape as yours. Mine is just rectangular..
Hey Keith - did you ever find parts? I just ordered two pieces for my pfaff 463 - my plastic gear shaft crumbled lol.
Love it. I've been fixing mine as well tha k's for the help and sharing
Very thankful mine isn't nearly as bad. Just needs an opener finger and some timing
I just received a bobbin case opener. I will do a video in a couple of days on how to install and time it.
Comment regler les dents de machine acoudre pfaff463
Minha maquina pfaf trancou como faço para destrancar? O volante não não gira.
bigger bolts/screws under my Pfaff 463 are really tight....what can i do to open them?
the only thing to use is one of these www.amazon.com/DEWALT-DCF887B-Li-Ion-Brushless-3-Speed/dp/B0183RLW8A/ref=psdc_551236_t1_B08TZYNGXJ?th=1
HI THERE IM A RETIRED INDUSTRIAL SEWING MACHINE MECHANIC I CAN TELL YOU THAT THE CAM YOUR NOT SURE ABOUT IS IN FACT IT OPERATES A KNIFE MECHANISM WHICH LOOKS AS IF ITS BEEN TAKEN OFF, IF THE 463 HAS 900 AFTER IT THEN ITS A UNDERBED TRIMMER I WOULDNT
GO WITHOUT THE SPUNG IT COLLECTS EXCESS OIL
Thank you, I have been trying for years to find out what that cam was for. In another video, another mechanic told me about the bracket that pivots around the bobbin housing is where the knife blade was mounted, it make sense now that bracket was operated by that cam.
Boa noite! Mostra como trocar correia dentada interna da máquina pfaff 463.
Assim como em todas as máquinas de costura industriais, você deve remover o rolamento do eixo principal, removendo primeiro o volante. Com a roda removida, o rolamento deve sair facilmente.
Não remova o anel elástico do rolamento. Você pode ter que usar algo como óleo diesel para dissolver o óleo seco entre o rolamento e a máquina.
Bom dia! Você tem um tutorial montando a pfaf 463
Hola buenas tardes, tengo una maquina 563 Pfaff, vi como devanaste el hilo del carrete, pero el problema es que cuando oprimo el pedal se mueve la aguja, que tengo que hacer para que la aguja de la maquina no se mueva cuando estoy devanando el carrete. Otra cosa donde conseguir la cartilla de manejo de la maquina. No se como se engrasa ni otras funciones que requiero aprender. gracias.
No puede, el Pfaff 563 no se desconecta del volante a la aguja, por lo que el volante gira y la aguja sube y baja. Ahora mi respuesta depende de si Google tradujo correctamente su pregunta.
Hi, I have the same machine with the thread cutter, I wanted to ask you something, when I push the fabric back with the lever sometimes the thread breaks, what can it depend on?
I'm sorry but I don't know how the thread cutter works, never seen one. I'll do some research on it
@@gmcxm211 thanks for the answer, but why do you think that the problem when the fabric backs off the thread is broken is due to the fact that the thread cutter is present? excuse for my english
take a video camera and try to find a way to mount it to where you can take a video where the bobbin is at. Then you might see what the thread cutter is doing. Or have someone sewing while you sit under the table and then you can watch it for yourself
Please a pfaff machine tutorial refence 563 thanks
Voting for this as well, I have a 563 that need a lot of tlc.
Hi, I have pfaff 260. can you disassemble and reassemble, pfaff 260 in video? I have a problem the zigzag doesn't engage, It will sew straight and the cam mechanism has no problem. I think a spring is missing. I would appreciate if you can do that. Thanks.
did you just buy this machine? If so it could makes a big difference, it could be more than just a missing spring.
@@gmcxm211 I bought it at craigslist los angeles
@@evelynsia460 good news is if it can sew straight stitches it's properly timed. I don't have a 260, just a 360 and there some differences between the two. now if you select a decretive stitch and the middle knob/level moves in one direction only, while sewing try gently to move the knob/level back. If there is no resistance then yes you do have a spring missing. If there any resistance than it just needs to be cleaned. The only problem with these machines, the decretive stitching isn't all that "crisp" as it is with the electronic sewing machines. Since these are all cams and spring regulated the needle never returns to a true zero. There will always be a thread size gap or off a width of a needle in some places. We're talking Model "T" Fords here compared to our computer controlled cars of today.
Hello. The plastic gear must not be replaced with a metal one ( ua-cam.com/video/Cfi0aKLPQF4/v-deo.html ). If the hook of the sewing machine gets stuck, then the plastic gear is a safeguard against the big problem. The gear will break and not cause much damage to the sewing machine. This gear is located just after the main shaft and transfers rotation to the hook of the sewing machine. Therefore, you cannot install a metal gear.
So, this was design to be a “safety fuse” and not just to make the machine run quieter? I can see that. Has there ever been a situation where the hook jammed to where it stripped out the teeth of the nylon gear?
I was sewing along and the thread got tangled up in the hook. The belt slipped on the hand wheel. Now I wasn’t using a clutch motor also my belt tension isn’t all that tight because I don’t want to wear out the bearings
@@gmcxm211 A side function of the plastic gear is a little less noise. But it is plastic because it is a fuse. There is no problem to put a metal one, and the adjacent gear is just that. Repairing with a metal gear when the shuttle is jammed can be expensive. The hook of the sewing machine may break. The motor may be damaged unless the overcurrent protection is activated. In addition, the small gear may be damaged from fragments. The timing belt may break. There can be many problems. If the plastic gear breaks, the shaft continues to turn and the shuttle does not turn. Therefore, there is no major damage.
You are a good mechanic! A lot of work has been done.
Buenas noches soy de Colombia y necesite q por favor me diga de dónde saco el tensor porq ninguno de los tornillos q tiene alrededor son para este
Hallo, I have just found this machine and thinking to buy it. But the
question raised: does it need an air compressor? The seller says it
does. Can you answer me please:) Thank you.
it probably does if it has a thread cutter or any other special operation. Now, for it just to sew, no it doesn't need air for that. but if it does have those features you can get an air compressor pretty cheap at harbor freight. Besides once you have an air co presser you'd be surprised how handy these things are
@@gmcxm211 It is the Pfaff463. We have one compressor at home and my husband is the same opinion about it as you. Thanks a lot for an fast feed back.
@@YtrSany cool, post a small video of its operation when you get it up and running, like to see it operate
THANK YOU!
محناج الترس بتاع الكرشي اجيبو منين
سلام اخي هل عندك مثلها كيف ازيتها اشتريت مثلها تماما ولا اعرف كيف ازيت اجزائها
Después del minuto 24:30 da un salto enorme, como desinstalo el sistema de lubricación????
Hola
Compré una, pero me doy cuenta que le cantan piezas y no sé dónde adquirlas
Aparte de que no sé si solo son esas piezas que le faltan o hay más
Me podrías apoyar?
@@arelybruno7600 Buenas tardes, en pfaff hay originales calle de vainilla en granjas México, el número no recuerdo, Mándame tu gmail y una foto con modelo y tal vez te consiga refacciones,
En cdmx, ¿ Cuánto pagó y en donde? Ok gracias.
Hi how I fix the knee lifter not working
remove the back panel then go to 10:30 in the video. move the knee lifter, the cam with the 2 screws should also move. if it does remove the front cover then go to 20:10 in the video and insure both hooks capture that bar you see.
Where do you order your parts from?
The best way is just to google the part you want.
Please tutorial machine industrial ref 467 Pfaff. Thanks
Thanks for posting,is this a walking foot
Cheers colin.
No, the 463 is not a walking foot machine. Pfaff 1245, 145 series are the walking foot machines.
What bobbins does it use. I just bought this machine for $160 but the girl could not find book or drawer with the spare parts but she’s gonna look later but for $160 for head n table with motor who’s complaining. LOL
You got a real deal for $160.00, the head alone is worth that much.
Em português
beautiful sos big
Many dirty this machine