I have tried many times and decided to use stainless steel welding rod to weld cast iron, the result is beyond my imagination. I recommend you to try it.
I can't believe u painted all the gasket surfaces of the compressor block!!! Also i can see the pistons are smeared with rtv sealant!!!! The lack of enthusiasm during the assembly process really hurts my feelings 🥺
Мойка и покраска вышла на новый уровень , Теперь новый прокладки и герметик , а не просто помыл-покрасил-готово.=))) Ждём , когда будут новые вкладыши, шлифовка , новые кольца и поршни , думаю через годик увидим. Это не реставрация , а техническое обслуживание !!!
Well, considering that most people are used to small Home Depot type units, yes this is "Giant". It's a Saylor Beall model 707 which is a 7.5 to 10hp pump. I've worked on 400hp machines where you need a ladder to reach the heads, and a block and tackle to remove parts. What gets me about this video is that they didn't tackle the most important part of the unit... The valves.
While that one came with high quality metal wheels it's worth mentioning you can add them to any horizontal compressor. (I use 8" scaffolding caster wheels because they slide into simple pipe mounts so one set can move many machines and machine tools.) Collecting all the old large diameter wheels you can makes life easy. Everything in my shop rolls.
In my opinion, repair air compressor it is always a risk, the vessel may be very oxidized inside, which is why it needs a visual inspection with an endoscope in order to guarantee its integrity. I'm not, in any way, criticizing the work you've done, but rather the risk of the vase being corroded after years of use and also after a long time stopped. Thanks for the video.
You guys from Asia, make a restoration cleaneing and painting... This is not restuaration this is cleaning. BTW you didn't clean the tank probably have 25 l water and rust inside...
The original paint is beautiful, I deliberately left it as it was, I cleaned it up and then applied it to a new layer of paint, thank you for watching and subscribing to the channel.
Радиаторную часть цилиндров красить нельзя, так как снижается теплоотвод при работе, следовательно, в емкость попадает больше конденсата и это способствует более быстрой коррозии воздушного баллона.
Helllo i have also this time of compressor and when i start the moter its too much heated can you please explain me in the comments that the outside compressor two places can i put water ?? Please please reply meeee
Thank you for viewing and subscribing. There are many types of air compressors; screw air compressors, oil-free air compressors....you should find out for yourself and buy yourself a suitable economic one.
No processo de trabalho, encontrei muitas dificuldades, por isso espero a sua compreensão, peço desculpas pelas deficiências. Prometo trabalhar mais e com mais cuidado. Obrigado pelo seu feedback
Thank you for your feedback. I have encountered many difficulties during the recovery process. I will try to correct and improve myself. Thank you very much.
hi. super giant super air compressor recovery project. i made 2 videos about the machine. you are watching the first video, my second video mainly fix burnt 3 phase motor. invite you and my channel to watch.Thank you for watching and subscribing to my channel
Спасибо за просмотр видео. Информация о компрессоре на алюминиевом штампе со временем стерлась, только некоторые данные, такие как вес 283 кг и двигатель 7,5 кВт - 10 л.с.
Baş yapıt ve güzel temiz işçilik elinize sağlık efendim saygılar
🤦♂️🤦♂️🤦♂️
i love welding cast iron!
Thank you very much, please watch the next videos
A video about how not to weld cast iron. Sweet
I have tried many times and decided to use stainless steel welding rod to weld cast iron, the result is beyond my imagination. I recommend you to try it.
ua-cam.com/users/gireshrathore
I can't believe u painted all the gasket surfaces of the compressor block!!! Also i can see the pistons are smeared with rtv sealant!!!! The lack of enthusiasm during the assembly process really hurts my feelings 🥺
I apologize for the shortcomings in the process. I promise to try harder to have great products and useful videos. Thank you very much.
@Restoration Product to add to his comment I would also put sealant around the holes for the bolts.
Disassemble and paint equals restoration don't you know and rtv
Location and phone number pls
Thats a monster, well done 👍👍
Thank you for watching and subscribing to the channel
Мойка и покраска вышла на новый уровень , Теперь новый прокладки и герметик , а не просто помыл-покрасил-готово.=))) Ждём , когда будут новые вкладыши, шлифовка , новые кольца и поршни , думаю через годик увидим. Это не реставрация , а техническое обслуживание !!!
хорошо брат не забывай смотреть мои видео почаще
very good restoration waiting for part 2
part 2 we only emphasize the burned motor
Another masterpiece! Such a pleasure to watch! Thank you 💕
Thank you very much. Your comments are a great motivation for us to strive and improve ourselves even more
ua-cam.com/users/gireshrathore
@@restorationproduct1718q
great! looking forward to see part 2
Thank you very much. Part 2 I just restored the burnt 3-phase motor and I've already published it. Please look forward to it
ua-cam.com/users/gireshrathore
Hardly a GIANT compressor but a great restoration guys. 👍👍👀👀👀👀👀
👍👍ok .thank you for watching and subscribing to the channel😃😃
It is ,next to mine !
Well, considering that most people are used to small Home Depot type units, yes this is "Giant". It's a Saylor Beall model 707 which is a 7.5 to 10hp pump. I've worked on 400hp machines where you need a ladder to reach the heads, and a block and tackle to remove parts. What gets me about this video is that they didn't tackle the most important part of the unit... The valves.
While that one came with high quality metal wheels it's worth mentioning you can add them to any horizontal compressor. (I use 8" scaffolding caster wheels because they slide into simple pipe mounts so one set can move many machines and machine tools.) Collecting all the old large diameter wheels you can makes life easy. Everything in my shop rolls.
with wheels moving is very easy, thank you for watching and subscribing to the channel
perfect...
Thank you for watching and subscribing to the channel. We are happy to have fans like you. We promise to work hard to not let you down.
Cool project.😊
Thank you for your compliment. Please watch my 3-phase motor recovery video released tomorrow
ua-cam.com/users/gireshrathore
Install after cooler and moisture trap with auto drain never worry about water again.
okay thank you for watching and subscribing to the channel
I hate these videos that someone is in such a rush to show the content that it either never has the ending.
👏👏👏
In my opinion, repair air compressor
it is always a risk, the vessel may be very oxidized inside, which is why it needs a visual inspection with an endoscope in order to guarantee its integrity.
I'm not, in any way, criticizing the work you've done, but rather the risk of the vase being corroded after years of use and also after a long time stopped.
Thanks for the video.
Your comments are very good and meaningful, I promise to draw experience for the next products. Thank you for watching and subscribing to the channel.
活塞安装方法错了，应该是活塞安装在气缸上在紧连杆这样效果要好很多，这台就这个技巧很多人不会，杭氧1.05的
谢谢你的收看。 我会从我的经验中学习下一个视频
You guys from Asia, make a restoration cleaneing and painting... This is not restuaration this is cleaning. BTW you didn't clean the tank probably have 25 l water and rust inside...
I have drained a lot of water inside the tank. Make sure the tank is empty, thank you for your feedback. Please continue to watch my videos.
Make sure the tank is still safe to use. Weak tanks are dangerous, because it's basically a bomb.
The compressed air tank is still thick. Only the paint is slightly peeled off. It is absolutely safe for users. The air pressure is up to 14 pounds.
@@restorationproduct1718 But, did you pressure test it with water?
@@jorismk1 and how about corrosion on the inside? its the inside that have most of the problems, not on the outside
@@killzone89 Yes, thats why you pressure test it with water. Water does not compress so if it fails it will not explode but just crack...
add after cooler and moisture trap with auto drain never worry about water again.
OK 👍👍
invite you to watch the next video.recovery of a 3-phase motor on fire
Tank corrosion?
Okay . Thank you for watching and subscribing to the channel
How did you assemble pistons with out ring compresser? And no hone?
The factory makes beveled cylinders, you just need to choose. It's very simple
A little paint can hide a multued of sin's
The original paint is beautiful, I deliberately left it as it was, I cleaned it up and then applied it to a new layer of paint, thank you for watching and subscribing to the channel.
😊😂 15:12
👍👍👍👏👏
Радиаторную часть цилиндров красить нельзя, так как снижается теплоотвод при работе, следовательно, в емкость попадает больше конденсата и это способствует более быстрой коррозии воздушного баллона.
хорошо .спасибо за ваши комментарии я буду учиться на своем опыте в следующих продуктах
El video se corta antes de terminar, pregunto: se le hizo protección a las poleas,
Gracias por mirar. A mi máquina de gasolina le faltan tanto como el protector de la correa. Lo haré yo mismo y lo taparé.
Y como se calibran los pistones ?
Hago estas cosas basándome en mi experiencia actual.
This is what we call around here a Craigslist overhaul. Basically do every unnecessary cosmetic thing and skip all the needed mechanical steps.
Thank you for commenting with us, I promise to try more. Thank you for watching and subscribing to the channel
Helllo i have also this time of compressor and when i start the moter its too much heated can you please explain me in the comments that the outside compressor two places can i put water ?? Please please reply meeee
Maybe your 3 phase motor has a problem, the compressor part is fine, you should check the motor
that hose you painted red it's for air cooling, now because of paint it's useless
The factory is completely painted. I paint to protect from oxidation. Thank you for watching and subscribing to the channel
@@restorationproduct1718 ok then, great video
Mientras funcione los comentarios maliciosos valen verga siga adelante i suba mas videos de compresores xfa
Muchas gracias, tenemos muchos otros videos interesantes para que veas.
I need this type of air compressor pump please.
Thank you for viewing and subscribing. There are many types of air compressors; screw air compressors, oil-free air compressors....you should find out for yourself and buy yourself a suitable economic one.
Sodara maukah anda membuat mesin 4tak dari kompressor udara 2silinder seperti itu🥲
Terima kasih telah menonton dan berlangganan saluran, kami akan memikirkannya
@@restorationproduct1718 akan terus mendukung anda
តើ អ្នកផ្តូប្រេងម៉ាស៊ីនបូមខ្យល់លេខប៉ុន្មានដែរ ១៥W 40W .....? តើម៉ាស៊ីនបូមខ្យល់អាចប្រើប្រេងម៉ូតូទូទៅបានអត់ ..........?
ម៉ាស៊ីនបង្ហាប់ខ្យល់អាចគ្របដណ្តប់ម៉ាស៊ីនម៉ាស៊ូតដើម្បីជួយសង្គ្រោះរថយន្តដឹកទំនិញ
Sei não!! Parece que está restaurando de qualquer jeito só para fazer vídeo. Restauração fake!!!
No processo de trabalho, encontrei muitas dificuldades, por isso espero a sua compreensão, peço desculpas pelas deficiências. Prometo trabalhar mais e com mais cuidado. Obrigado pelo seu feedback
I switched off when you used the wrenches the wrong way
Thank you for your feedback. I have encountered many difficulties during the recovery process. I will try to correct and improve myself. Thank you very much.
If you arent going to show us the entire project, dont show anything!
hi. super giant super air compressor recovery project. i made 2 videos about the machine. you are watching the first video, my second video mainly fix burnt 3 phase motor. invite you and my channel to watch.Thank you for watching and subscribing to my channel
Хорошо бы если автор написал бы марку модеть и какого года этот компрессор
Спасибо за просмотр видео. Информация о компрессоре на алюминиевом штампе со временем стерлась, только некоторые данные, такие как вес 283 кг и двигатель 7,5 кВт - 10 л.с.
why you did not show us you cut video when time to put cylinder in. cut video not good
Thank you for watching and subscribing to the channel. Because this product is too heavy, we need someone to help us cut the excess.
Price to pk
🤦♂️🤦♂️🤦♂️
Suck restoration..GROS QUALITY
ok friend.thank you for watching.please continue to watch my videos
ভাইজান প্লিজ হেল্প আপনার নাম্বারটা দেন
আমরা একে অপরের থেকে অনেক দূরে থাকতে পারি, একে অপরকে দেখা কঠিন
By phone number then
if there's anything you don't understand, just go to my channel, chungstooi restores a lot of products, and is very detailed.
No video of it running
In this video, I just focus on making air compressors and the video on winding the motor and running the machine I posted shortly.