Parkside Battery Problem Factory Defect? The Green and Red LEDs Flash

Поділитися
Вставка
  • Опубліковано 11 січ 2023
  • In this video I will show you what problem I faced with a parkside battery.
    A relatively good battery, I have no idea how it worked at first
    Thanks for watching . And do not forget, Like and Subscribe
    Due to factors beyond the control of CMC DIY, it can not guarantee against unauthorized modifications of this information or improper use of this information. CMC DIY assumes no liability for property damage or damage incurred as a result of any of the information contained in this video. CMC DIY recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of CMC DIY, no information contained in this video will create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from the improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not CMC DIY.
  • Навчання та стиль

КОМЕНТАРІ • 26

  • @builtstrongertolastlonger3158
    @builtstrongertolastlonger3158 11 місяців тому

    Got a brand new battery out the box yesterday and it's doing this . Great video . I will try take it back for swap but I've binned receipt 😬 if they don't accept I shall look to see if this is the same solution thank you

  • @londoncity1
    @londoncity1 Рік тому +1

    Super!

  • @marcellieffrig4478
    @marcellieffrig4478 7 місяців тому

    Très bien

  • @ayhamalsalam7000
    @ayhamalsalam7000 6 місяців тому

    Good job. I have the same battery and all the cells are working. When I measure the battery output to give any reading, note that the fuse is intact and the connections are correct. Where is the fault? Thank you

  • @tedco-Theo
    @tedco-Theo 2 місяці тому

    Font elles reellement 20 Volt, ces batteries Parkside ? ou 18 Volt ? Merci

  • @emadfazil
    @emadfazil 8 місяців тому

    I have a problem, my battery shows 19v but not working the drill.
    Ps: the drill works fine
    The cells and connectios are fine.
    What could be the problem?

  • @alexignatov3837
    @alexignatov3837 4 місяці тому

    I had such a problem and it turned out to be a cold solder on the temperature sensor. I soldered it and all was well

  • @garycurtis294
    @garycurtis294 Рік тому

    Hello, just a quick question; Parkside 20v-4ah-80wh battery (PAP 20 B3) will charge (constant red LED) but as it gets near the end of the charging cycle it will change to green LED (charge complete / trickle charge) for 2-3 seconds then straight back to constant red LED. It will continue to do this until the battery is removed. Battery check on the side of the battery shows it as battery is full and a test with a multimeter confirms this. Also the charger itself (PLG-20-C1) gets quite hot in the process but the battery stays cool to the touch. Any advice, if you can, would be greatly appreciated. Thank you.

    • @CMCdiy
      @CMCdiy  Рік тому

      Hi
      After continuous charging, when the red LED shows again and the charger heats up, what is the voltage of the cells? It should not exceed 4.2V. Can you try the charger with another battery?

    • @garycurtis294
      @garycurtis294 Рік тому +1

      @CMC DIY Thank you for your reply, I tested charger with another 4ah batt and the same thing happened, then tried both the 4ah batteries on another charger (borrowed from uncle) and they finished charging as normal. Nothing strange with the LED's. So thanks to your advice, it must be a fault in the charger itself which is still under warranty. Thank you, again, for taking the time to help.

  • @neculaiavram4902
    @neculaiavram4902 7 місяців тому

    Va salut cu respect am o problema 2 celule de la un acumulator parkside de 4A primele nu se mai ăncarcă au 3,6 v restul au 4,2 v acumulator nou cu 2 ăncarcări si dacă ami recomandati săi schimb ce acumulatori ămi recomandati o zii bună

  • @LyubomirIko
    @LyubomirIko 7 місяців тому

    When "fully charged" my battery shows only 2 out of 3 bars. Could the problem be the same? Because your indicator seems to shows only 1 bar...

    • @Cedo86
      @Cedo86 5 місяців тому

      Check the voltage with a multimeter, a new one, charged and in good condition must be 20.5V and above.
      Yours is probably just a little spent..

  • @Sam-pc3tb
    @Sam-pc3tb Рік тому +1

    Hi I had the same problem. What should I do

    • @CMCdiy
      @CMCdiy  Рік тому +1

      First check the connections, then the voltage of each cell.
      The cells should have the same value

    • @Sam-pc3tb
      @Sam-pc3tb Рік тому +2

      Thanks a lot

  • @theyjustwantyourmoney4539
    @theyjustwantyourmoney4539 3 місяці тому +2

    Poor quality control in manufacturing, this is not acceptable

  • @ChipMIK
    @ChipMIK 24 дні тому

    1 cell collapsed & adding 20V this way the remaing four cells got 5V pr. Cell......

  • @MrGodsking
    @MrGodsking Рік тому +1

    can you please fix my batteries

    • @CMCdiy
      @CMCdiy  Рік тому

      I don't fix batteries, I just suggest how to fix it.

  • @PoetryFilms
    @PoetryFilms Рік тому +4

    Garbage battery sold by LIDL and others. Quality control is horrible. Who has the time and expertise for all this faffing around? LIDL will be getting mine back

    • @CMCdiy
      @CMCdiy  Рік тому

      Hello
      This video is only informative, I'm not saying they are good or bad.
      It is a video to give an idea to those who have problems with these batteries

    • @LoneWoolfiiie1111
      @LoneWoolfiiie1111 8 місяців тому +1

      ​@@CMCdiythank you for that my friend, we others that likes to learn how to fix things apriciate it 😊😊🙏

  • @loveyourfreetimenow3270
    @loveyourfreetimenow3270 Рік тому +1

    Super!

    • @CMCdiy
      @CMCdiy  Рік тому +1

      Thank you very much!