GM S10, S15 and Sonoma Coilover Suspension Installation

Поділитися
Вставка
  • Опубліковано 18 гру 2024

КОМЕНТАРІ • 266

  • @deankay4434
    @deankay4434 2 роки тому +5

    At 2:23, this is the EVAP system fuel tank solenoid, not the emissions solenoid. It is normally open to all air into the activated carbon canister until enough drive time has past to close it and open the purge valve on the engine with the green port used for diagnosing EVAP leakage. During refueling, hydrocarbon rich air exists the tank at the highest spot to capture organic fumes from the tank. This allow refueling without constant shut off at the pumps handle. The EVAP system is completely separate from the emissions system except during purge as extra fuel vapors come into the engine without coming from the injectors and no code is set as the PCM’s fuel mapping is disabled during this time & also if above 80% of full or 10% below empty.
    ASE Master Tech since 1978.

    • @ThatLS10
      @ThatLS10 2 роки тому

      Completely useless info but hey, if you only know one thing, make sure you put it everywhere

    • @deankay4434
      @deankay4434 2 роки тому +2

      @@ThatLS10 Unfortunately, I had every system to work on, plus teach. Pass your I-9 security for Raytheon holding 30+ 4hr tech seminars in 7 states. I have complete knowledge of all systems including those you have never hear of. You are welcome.

    • @photondebuger45
      @photondebuger45 Рік тому

      ​@@ThatLS10 you say that now to tho you'll be looking for this comment on how the evap system works when you get a check engine light for it evap systems are annoying to deal with.

    • @ThatLS10
      @ThatLS10 Рік тому +1

      @@photondebuger45 i’m a red sealed mechanic in Canada.. so i doubt it

    • @photondebuger45
      @photondebuger45 Рік тому

      @@ThatLS10 oh quite good, nevermind then

  • @ritchiemeza
    @ritchiemeza 4 роки тому +24

    in what world is having to cut/relocate/reweld “bolt-on”?

    • @shoopdawooplazars
      @shoopdawooplazars 2 роки тому +3

      the cutting and relocating is all super simple. nothing was fabricated on the spot so id still call it bolt on

  • @joe352001
    @joe352001 5 років тому +47

    You sold it to me until i saw it was 4500 dollars

  • @wtfobiden
    @wtfobiden Рік тому +1

    man that drill bit gave him a ride

    • @wtfobiden
      @wtfobiden Рік тому

      now time take it all back apart to do frame off restomod and sandblast frame rails and coat them 👌

  • @itocivic
    @itocivic 5 років тому +11

    This kit is amazing.!
    It would be nice if the front control arm comes with 3” more longer so we can fit Corvette wheels without spacers..!

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      Nothing wrong with spacers I have been running 2in in front and 1in rear for 4 years for my c4 wheels

  • @11green11
    @11green11 5 років тому +17

    Damn, that was a killer walk through 😎👍

  • @Oncebitten10
    @Oncebitten10 2 роки тому +15

    Pricy for sure. Not many S10's out there worth the cost of this kit. I have a very clean 170K mile ZERO rust truck but it's hard justifying the cost. I'd bet at 3K you guys would sell a ton more kits and still make good money. Vastly expand the customer base. I for one would be a buyer!

    • @nomadicjoe6124
      @nomadicjoe6124 2 роки тому +4

      you are right. if you drop the price of anything by 50% it would sell faster. With your wisdom I now wonder why its out of your budget?

    • @Oncebitten10
      @Oncebitten10 2 роки тому

      @@nomadicjoe6124 LOL. Didn't say it was out of my budget just overpriced for the target market. My daily drivers are a TRX and an F-Type R. I'm pretty sure I could squeeze the kit into my budget. Actually , I have started on my S-10 build that includes this kit, but I changed out the coil overs for Vikings. Thanks for the comment.

    • @nomadicjoe6124
      @nomadicjoe6124 Рік тому

      @@Oncebitten10 TRX and F-Type R.... gross waste of money... and you bought the kit you claimed to be overpriced too, cograts!

    • @Oncebitten10
      @Oncebitten10 Рік тому +8

      @@nomadicjoe6124 Thanks for your constructive comments. I will immediately focus on redirecting my focus and life goals so that I may someday achieve YOUR level of "wisdom" and intellect. I am confident the profound impact your comments have made in my life will guide me to make better decisions, thus improving my automotive experiences. Thanks again for just a few of what can only be assumed to be many enlightening, educational, and fulfilling volumes of contributions you have undoubtedly made to the automotive enthusiasts community 😄

    • @Up2Trbl
      @Up2Trbl Рік тому +1

      First of all, I think this is more for the "money no object" kind of builds. But beyond that, this kit was likely VERY expensive to produce (in material + R&D). $4500 seems pretty reasonable to completely redesign the suspension of a truck for a very niche market.

  • @nickbrown6560
    @nickbrown6560 5 років тому +108

    When your suspension costs more then the truck lol

    • @mistahferguson6240
      @mistahferguson6240 3 роки тому

      How much?!?

    • @lege46
      @lege46 3 роки тому

      @@mistahferguson6240 like 6k

    • @sterlingfrosty1610
      @sterlingfrosty1610 3 роки тому

      Truck in mint condition 7 grand……suspension 🥸

    • @BartlettDaveJr
      @BartlettDaveJr 3 роки тому +2

      Prices have gone up since then, those trucks still aren't worth any more

    • @Scott9181970
      @Scott9181970 3 роки тому +5

      I mean... my S10 Blazer with less than 110k on the clock cost me $80, so... a full tune up costs more than my truck 🤣

  • @MiyamotoMusashi9
    @MiyamotoMusashi9 2 роки тому +1

    Seems like the front places the whole weight just on the old shock mount... it looks structured . But seems like it should be a bit thicker or re-inforced either by a weld in or sandwich plate that somehow wraps around and under the old spring cup

  • @mikef-gi2dg
    @mikef-gi2dg 4 роки тому

    I have had my v8 s-10 blazer 88 for a long time. For a leaf spring ride it don't handle too bad. If they made a kit for 2wd blazer, with a stronger rear than a 7.5, we would be cooking.

  • @brassnyuks3849
    @brassnyuks3849 4 роки тому +18

    I couldn't imagine spending 4500$ on a suspension upgrade and not painting the differential or at least buying a new differential cover.

    • @jjj55561
      @jjj55561 3 роки тому +1

      Amen, i would remove the bed and paint everything but the fuel tank.

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      @@jjj55561 why wouldn't you paint the tank

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      I'd have to have the rear end from a 4wd s10. Rear disc brake and 2inches wider.

    • @cccspokesmanandcofounder
      @cccspokesmanandcofounder Рік тому

      @@scootersonlyrepair6773 and an ugly offset set of rear wheels

  • @kevinramirez-uc2ul
    @kevinramirez-uc2ul 4 роки тому +21

    Nice BUT almost $5000 with tax ! what?! . lets be real that kit is only worth $1500 tops !

    • @hitlersmissingtesticle69
      @hitlersmissingtesticle69 Рік тому

      3 years later and price hasn’t changed, you still can’t get another truck and convert it this easily though

    • @miker-s7219
      @miker-s7219 Рік тому

      @@hitlersmissingtesticle69 almost 6000 now 😅

  • @garypease7414
    @garypease7414 5 років тому +6

    Can i get it in 4wd?

  • @stellingbanjodude
    @stellingbanjodude 5 років тому +4

    Would this kit also fit the s10 blazer or Gmc jimmy?

  • @v.e.7236
    @v.e.7236 5 років тому +4

    I bought one of their weld-in triangulated 4-link kit w/ Shockwaves for my 2DR 2WD Blazer and look forward to enjoying a much better ride quality from this heavy little beast. Need to get their True Steer systems to help the handling around the twisties. $$$ Pretty soon my after market parts will out-cost the price of the vehicle when new and know I'll never see a "return" on my investment. I'll drive it till the day I die and hope someone appreciates it after that.

    • @mikef-gi2dg
      @mikef-gi2dg 4 роки тому +1

      didn't know that had something that fit blazers...utt oh,got to check this out....

    • @ghidraa9340
      @ghidraa9340 4 роки тому

      Really interested on your take with the 4Link. How's the performance?

    • @v.e.7236
      @v.e.7236 4 роки тому

      @@ghidraa9340 Sadly, my Blazer was totalled by a drunk, while it was parked outside my sister's place, one night, and I hadn't installed any of the Ride tech stuff I bought - a complete $5K system just sitting in my garage collecting dust.

    • @ghidraa9340
      @ghidraa9340 4 роки тому

      @@v.e.7236 Wait you have the Whole Ride Tech Coilover set in your garage.. collecting dust?

    • @v.e.7236
      @v.e.7236 4 роки тому

      @@ghidraa9340 Complete w/ Shockwaves, not coil-overs, but, yes. Kills me.

  • @kfbrockp
    @kfbrockp 4 роки тому +14

    I'd get it if I didn't have to sell my s10 to afford it

  • @onewheelup
    @onewheelup 5 років тому +1

    god i couldnt put any of that nice stuff on there without painting all that rust every where,its bad looking man.but i love what you did who ever owns it is lucky,i love cornering

    • @ridetechtv
      @ridetechtv  5 років тому +1

      this is one of our employees son's first truck, trust me all that work will happen, just didn't happen before the video shoot.

  • @compa_choo
    @compa_choo 9 місяців тому

    How low can it go tho? Doesn't look like the rear would allow it to be slammed

  • @joeyvillarreal7281
    @joeyvillarreal7281 Рік тому

    If you do a v8 swap is there a difference in parts?

  • @Happyfacehotwheels
    @Happyfacehotwheels 5 років тому +3

    Why not put paint down before installing this kit? The end result will make that truck look so much better.

  • @klappahsunion8089
    @klappahsunion8089 22 дні тому

    Alignment shims on control arms?

  • @Matp345
    @Matp345 5 років тому +4

    Such a beautiful kit. True quality components. I’d say I wish they’d make it for A dakota but i’m sure that kit is north of $1500. A bit much for my blood.

    • @wyattthompson3368
      @wyattthompson3368 5 років тому

      It 4500 bucks

    • @Matp345
      @Matp345 5 років тому

      Wyatt Thompson good god. Yea a bit much for me.

    • @koshnaranek2317
      @koshnaranek2317 5 років тому

      $4500 that almost or certainly exceeds the value of the truck not worth it even with custom wheels. There's no added value when it comes time to trade in dealers don't pay more for custom anything unfortunately.

    • @Matp345
      @Matp345 5 років тому +2

      KOSH Naranek It’s all a matter of preference. As well as beauty is in the eyes of the beholder . You never get what you put into a car, Any good car guy can tell you that. It just is what it is. I’m in the process of putting close to $5k Worth of powertrain in my $1500 S10. I’m sure I’ll be another $1k in suspension. If I’m lucky I could squeeze 4K out of it when I’m done, but I don’t care because you don’t plan on getting rid of it. It’s not a lease. You can’t put a price on minitruck fun. Even if you have the newest s10 (04) you’d be insane to trade it in. They’re not even in the books anymore and most dealers will end up junking them which is terrible shame. Sell them privately.

  • @gering46
    @gering46 5 років тому +2

    Will this work on a 2000 xtreme blazer?

    • @ridetechtv
      @ridetechtv  5 років тому

      Sorry but it will not fit the Blazer.

    • @gering46
      @gering46 5 років тому

      Well that sucks

    • @mikef-gi2dg
      @mikef-gi2dg 4 роки тому

      @@ridetechtv any chance you will make one?

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      Yes it will. If it's 2wd

    • @gering46
      @gering46 3 роки тому

      @@scootersonlyrepair6773 thank you, I’ll keep that in mind if I decide to buy another

  • @odinvalhalla8912
    @odinvalhalla8912 5 років тому +1

    Where can I get this entire kit set up for my 01 s10

    • @ridetechtv
      @ridetechtv  5 років тому

      You can get it directly from us or check out some of our dealers.... www.ridetech.com/applications/trucks/1982-2003-gm-s10/1982-2003-s-10-s-15-and-sonoma-complete-coilover-system/

    • @ridetechtv
      @ridetechtv  5 років тому

      www.ridetech.com/info/dealers/

  • @charliemclaughlin1042
    @charliemclaughlin1042 5 років тому +1

    Awesome looking system would love to try it out 👍👍👍

  • @maxcuster3143
    @maxcuster3143 4 роки тому +1

    Can you use it as a work truck if I install it on my s10

    • @ridetechtv
      @ridetechtv  4 роки тому

      Sure Can, depending on the load your pulling or hauling may require coil adjustment, or more air pressure if using the shockwaves.

  • @67judge
    @67judge 5 років тому +3

    Before installing that kit with all of that labor included. I would rust proof the entire undercarriage with Por 15 or another equivalent.

  • @banefarooqbey7809
    @banefarooqbey7809 5 років тому +2

    Do you guys have a similar setup for a GMT-400/ 88-99 Chevy Silverado or GMC Sierra C1500?

    • @ridetechtv
      @ridetechtv  5 років тому

      Check this out.... www.ridetech.com/products/suspension-packages/coilover-suspension-system-1988-1998-c1500/

  • @issaclizardi-lopez8002
    @issaclizardi-lopez8002 2 роки тому

    Is there a kit for the 89 to 93 chevy s10 cause that would be awesome let me know

  • @junkyardjumper7670
    @junkyardjumper7670 5 років тому

    So on the ball joints... When one goes out would i need to get new from you guys our would oem fit in there and how much do your guys ball joints run

  • @photondebuger45
    @photondebuger45 Рік тому

    Yo thats way too COOL tho is that ok to have it using the diff cover or in front of the diff cover as part of the whole thing?

  • @natesmatco1
    @natesmatco1 2 роки тому

    Will this work on blazers? And 4wd?

  • @mikewebster9500
    @mikewebster9500 6 років тому +3

    What if I'm not running the stock rear end?

    • @TheBlazerSociety
      @TheBlazerSociety 6 років тому

      Mike Webster I second that

    • @ratrodo3113
      @ratrodo3113 5 років тому +1

      Same here. Running narrowed explorer 8.8.

  • @anthonybernal5680
    @anthonybernal5680 2 роки тому

    I'm really interested in pickin this up. How much is the product. And how much h would it be to install or st least a estimate??

  • @Busa0069
    @Busa0069 5 років тому

    That cross bar the upper arm is attached to is pretty thin gauge metal, wonder how it takes all that strain of the rear end torquing around.

  • @alanclark9286
    @alanclark9286 3 роки тому

    Has anyone put a kit on an s10 blazer?? The website says this kit don’t fit please help

    • @ridetechtv
      @ridetechtv  3 роки тому

      unfortunately, the rear frame is completely different.

  • @imemovengeance
    @imemovengeance 5 років тому +1

    Whats the info on the wheels? Brand, size, width, backspacing and offset? Thanks

    • @ridetechtv
      @ridetechtv  5 років тому +2

      US MAG Rambler U117 Front-18x8 4.5" Backspace Rear 18x9.5 5-1/4" Backspace Tires are BFG 245/40/18 & 275/40/18 us-mags.com/rambler-u117-w-12064.htm

  • @DomesticTaskForce
    @DomesticTaskForce 5 років тому +1

    Will this work for 4wd?

    • @drummin84
      @drummin84 5 років тому

      No 4wd s10's use torsion bar front suspension. There is an axle driveshaft where the spring would be located.

    • @DomesticTaskForce
      @DomesticTaskForce 5 років тому

      @@drummin84 still doesn't mean you cant cut out the torsion bar cross member and put coil overs to the factory shock location like this one. And this may be one of a few kit that does work with the front axles......

  • @aaronlyons4795
    @aaronlyons4795 5 років тому

    How does this kit work if your racing? Any issues

  • @brandonk73
    @brandonk73 2 роки тому

    What size wheels are does?

  • @mccoy786
    @mccoy786 5 років тому +4

    and try not to drill a hole in the box floor

  • @lucky13sss10
    @lucky13sss10 5 років тому

    Question, will yall make the wishbone mounting bracket on the axle to clear a girdle support cover?

  • @jeffreykalapanalono4216
    @jeffreykalapanalono4216 5 років тому

    is there a Kiki For a 08 chevy colorado

  • @suavehouse5150
    @suavehouse5150 5 років тому

    Will this fit a Nissan Hardbody?

  • @travislee2014
    @travislee2014 4 роки тому

    Hi i have a 2001 chevy s10 kinda simular to this truck in video will this kit fit my truck and do you have a website where i can buy this same kit but i want the air ride and also if i c notch my frame will i be able to sit my truck on the ground with this kit

    • @ridetechtv
      @ridetechtv  4 роки тому

      Hi Travis. Check out the S10 section on our Trucks page here for the complete air ride version of this kit: www.ridetech.com/applications/trucks/

  • @garyhayes4756
    @garyhayes4756 5 років тому

    What about us guys running narrowed 8.8 exploder rear ends

    • @ridetechtv
      @ridetechtv  5 років тому

      nothing yet, let me speak to engineering.

  • @adamm2716
    @adamm2716 4 роки тому

    i have a 1950 f-1 with a s10 frame. i could use a arms that are wider than stock to make the tires fit better. if i buy the kit can i get a arm made for that or you don't do that?

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      Get a cvpi frame Instead keep the Ford a ford.

    • @adamm2716
      @adamm2716 3 роки тому

      @@scootersonlyrepair6773 it was a rusty pile of parts a customer gave to me to cover their late bill it had no frame or engine. and i was like 18 and poor. also who cares about ford in a ford. hot rodding is about riding and having fun. not being a puritan.

  • @danielortiz7638
    @danielortiz7638 Рік тому

    Pwooo amazing how much for that dude I have Sonoma 99

  • @28EduardoSierra
    @28EduardoSierra 4 роки тому

    Those are fox shocks 😎 for s10 nice finally

  • @Muddytrickle
    @Muddytrickle 4 роки тому +1

    the cost of going fast and handling is not cheap regardless of what you start with. So my V8 S10 Blazer cost me 3k. Has a nice little LT1 350 and it scoots. I would love to do this but all i seem to know is how to make a junk car cost me a lot and sell for very little.

    • @ghidraa9340
      @ghidraa9340 4 роки тому

      Thats what i'm saying.. I picked up a clean 2003 Single cab Zq8. Right now I'd like to have a V8 but I'd prefer upgrading the suspension first. Just can't find any real reviews on how this entire kit handles BEFORE and AFTER.

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      @@ghidraa9340 if you go ls1 it's only 90lbs more than the 4.3 so probably not a lot of difference. Add 45lbs to the rear and you're balanced

    • @scootersonlyrepair6773
      @scootersonlyrepair6773 3 роки тому

      Basically relocate the battery.

    • @kushpaladin300
      @kushpaladin300 2 роки тому

      @@scootersonlyrepair6773 or just tie down a crate to the bed and add 3 15 LB dumb bells 🤷‍♂

  • @bob119911
    @bob119911 2 роки тому

    whish they sold the front end kit separate

  • @kalaniebaniz2626
    @kalaniebaniz2626 6 років тому +8

    Hefty price tag. Sweating me out. Goals though.

  • @that.ratchet.ranger94
    @that.ratchet.ranger94 3 роки тому

    How much for you to do this to my s10

    • @ridetechtv
      @ridetechtv  3 роки тому

      the S10 Coilover package is $4900

    • @that.ratchet.ranger94
      @that.ratchet.ranger94 3 роки тому +1

      @@ridetechtv oh nevermind then lol I paid 400 for my truck

  • @SrHide-iz7pf
    @SrHide-iz7pf 5 років тому

    Works on Blazer too???

  • @lanternprime4081
    @lanternprime4081 4 роки тому

    So, according to the website this 4 link kit wont fit an 03 xtreme?

    • @michelleberry-1314
      @michelleberry-1314 3 роки тому

      lol, Looks like the truck in the video is a zq8. Kind of dumb the website says it won't fit a 03 xtreme. However, 03 xtreme and 03 s10/sonoma in general compared to the truck in this video have a different vapor canister with a wider canister bracket and a plastic fuel tank instead of steel. The vent valve on an 03 is located behind the canister just inboard of the frame, so its already out or the way. But with the different canister, it may need to be relocated all together to fit this kit.

  • @callofgeorge
    @callofgeorge 5 років тому

    what wheels are these? US mags right?

  • @deadendgarage5401
    @deadendgarage5401 5 років тому

    Can you still use the stock rear sway bar with this kit?

  • @6778ERICK
    @6778ERICK 2 роки тому

    Quiero saber el tamaño de los aros y las llantas por favor

  • @slamsuzu3222
    @slamsuzu3222 3 роки тому

    Would this work with an 93 Isuzu pickup ?

  • @mikef-gi2dg
    @mikef-gi2dg 4 роки тому

    If you made a kit for 88 s-10 blazer 2wd, with a stronger rear choice like 8.5 10 bolt, or car or truck 12 bolt, I would buy it today.

  • @gabrielsmithful1
    @gabrielsmithful1 5 років тому +3

    I'll buy this when i do the 2.7 turbo swap

  • @codywright3082
    @codywright3082 3 роки тому

    What size wheels?

  • @brandonhagle9699
    @brandonhagle9699 5 років тому +3

    How low do the coil overs lower the truck from stock ride height? I looked on your website but could not find it.

  • @exhaustus7437
    @exhaustus7437 6 років тому

    I need a solid kit like this for my Nitro. More for quality than lowering though.

  • @РоссийскаяФедерация-ъ2ю

    The most easiest job here and my first job before after high school was tire tech.

  • @junk77hd
    @junk77hd 6 років тому

    I'm looking for something to do with my 1995 Roadmaster it's a B-Body . But what's on the market for these.?

    • @pelvicthrust119
      @pelvicthrust119 6 років тому +1

      I'm sure they have something because it's basically an impala

    • @vermili0138
      @vermili0138 5 років тому

      Most likely you'll find front and rear sway bars, lower and upper control arms, and coilovers from a few companies. UMI, BMR, QA1, Global West, and SpeedTech offer a few options for each. The price is a bit high if you're on a tight budget. Like the guy before stated, it's basically an impala with a different shell.

  • @lbank4526
    @lbank4526 4 роки тому +1

    My OCD wanted to clean and paint all that rusty frame and rear-end

    • @chumps7974
      @chumps7974 3 роки тому

      Mine too. I was thinking a good cleaning and coating in black

  • @i2devus4u
    @i2devus4u 5 років тому

    Can you please do a 1997 Chevy suburban 2wd

  • @cccspokesmanandcofounder
    @cccspokesmanandcofounder Рік тому

    That’s the evap VENT solenoid. Not the purge.

  • @mauiboy96768
    @mauiboy96768 5 років тому

    This will not pass safety check here in my state (HI) do to the fact that you cut the frame.

  • @harryhuarcayamaturrano6515
    @harryhuarcayamaturrano6515 5 років тому

    para una gmc jimmy 1993 ?

  • @RivalYoter97
    @RivalYoter97 Рік тому

    Imagine 2 hand jammin a 3 pound hammer 😂

  • @MIDNIGHTSAVAGE3
    @MIDNIGHTSAVAGE3 6 років тому +3

    First gens???

  • @BIGPOPRL
    @BIGPOPRL 5 років тому

    Cool piece of gear! Thanks for the video

  • @shortbedstan
    @shortbedstan 4 роки тому

    any plans on doing a silverado/sierra install video?

  • @travislee2014
    @travislee2014 4 роки тому

    Wow i didnt look at comments till after i wrote my text comment in 4500 is alot for me to just lower my truck guess ill be going another route

  • @brayannexon4613
    @brayannexon4613 5 років тому

    SO would this work if my truck has a ford 8.8" rear end?

    • @christopherhorton3555
      @christopherhorton3555 5 років тому

      Maybe not this exact setup but I'm sure they can accommodate for that.

  • @ricardocruz9352
    @ricardocruz9352 5 років тому +1

    But its a nice setup just too salty for s10

  • @jarrodburnett1902
    @jarrodburnett1902 6 років тому +1

    I would of thought a kit like this would include a panhard bar of some sort

    • @martymccord9875
      @martymccord9875 5 років тому +1

      Pan hard bar isnt needed with a triangular 4 link. The triangular part (wishbone) keeps the rear centered and from swaying

  • @davdhortaramirez7635
    @davdhortaramirez7635 4 роки тому

    Ese chasis es dueño de mucho óxido.

  • @luizalberto2223
    @luizalberto2223 5 років тому

    Tinha que ter umas firmas dessa aqui no Brasil.
    O único problema , seria os altos impostos. Aí estraga tudo.

  • @adventures223
    @adventures223 3 роки тому

    Cant understand why people like lowered trucks looks like the coil springs and shocks are bad when lowered rides rough you feel every bump in the road it banges and when hitting bumps scrapes on driveways and inclines the only thing low that is right are sport cars corvettes mustanngs ect but to each its own

    • @ridetechtv
      @ridetechtv  3 роки тому

      I bet you would be surprised just how good these truck ride. when a vehicle is lowered properly they ride just as good, if not better than sports cars.

    • @adventures223
      @adventures223 3 роки тому

      @@ridetechtv true i am sure they ride good but its harsh on bumps and scrapes on inclines and terrible if you had to drive in the snow or off road or tow i just like the way a 4×4 sits but to each there own i have a 2000 chevy s10 extreme and i am lifting it 3 inches i got it for very cheap with a 124000 on it shoul of just sold it or traded it for a 4×4

    • @kushpaladin300
      @kushpaladin300 2 роки тому

      that's why a lot of people who are lowering their trucks go with airbags. that way if you don't want it low you can still have stock ride height. people that lift their truck are trying to compensate for something in my opinion. small dick big truck

  • @johnwrench7736
    @johnwrench7736 6 років тому

    Is there a kit for blazers

    • @searchyo8730
      @searchyo8730 6 років тому

      I'm pretty sure it be the same

  • @craigr13666
    @craigr13666 5 років тому

    2dr Blazer? Got a link for a video if I go with air ride? As far as installing the air ride system? You can use mine for a test and fit vehicle for a video if you want!😁🤷🏻‍♂️

  • @SOLDOZER
    @SOLDOZER 4 роки тому +5

    $4000 truck, $5000 suspension.

    • @Jugg215
      @Jugg215 4 роки тому

      Ive owned multiple s10s and never paid over 2500 for any of them. This is crazy

    • @SOLDOZER
      @SOLDOZER 4 роки тому

      @@Jugg215 My point was the suspension cost more than the truck

    • @Jugg215
      @Jugg215 4 роки тому

      @@SOLDOZER Yea i know. That shits crazy as hell.

  • @halohunter5217
    @halohunter5217 5 років тому +11

    Anybody else cringe while they put new parts on an old dirty, rusty frame without cleaning it up or anything?

  • @user-fm6ny3uo2b
    @user-fm6ny3uo2b 4 роки тому

    *EVAP canister vent solenoid

  • @stevemadak6255
    @stevemadak6255 2 роки тому

    Lol before removing anything its a good idea to fix that nasty leaking differential !!

  • @Smokey-88
    @Smokey-88 5 років тому

    Funny you said purge solenoid the first time

  • @frankbarlow3154
    @frankbarlow3154 5 років тому

    Kit for 1985 s10 blazer?

    • @shyyphotography
      @shyyphotography 5 років тому

      this kit costs more than 3 of those trucks. just get a 94+

    • @frankbarlow3154
      @frankbarlow3154 5 років тому +1

      @@shyyphotography not sure your making sense? I asked if the make one for a 85 s10 blazer . Nothing to do with the value of my blazer or buying a second gen .

    • @frankbarlow3154
      @frankbarlow3154 5 років тому

      @@AnnDee4444 thanks

  • @michaelanderson4836
    @michaelanderson4836 5 років тому +1

    4500 pricey for that kit

    • @jimthomas777
      @jimthomas777 5 років тому

      michael anderson , that's more than the truck cost , some good shock absorbers and I'm good to go

  • @chevyboyforlife4234
    @chevyboyforlife4234 4 роки тому

    I don't understand why y'all did not sand and paint anything the bracket that went over the gas tank bracket y'all just put it right over that rust and everything then when you have the differential cover off you might as well sanded that down and painted it to wow

  • @ja5435
    @ja5435 4 роки тому

    You’d think they would have at least painted the rust colored metal frame

  • @LsBluu
    @LsBluu 3 роки тому

    Nice info! Check out some of my how to videos on my Ls Swapped S10!

  • @Ohiocountryboy-se2cn
    @Ohiocountryboy-se2cn 6 років тому +2

    4500 i think ill stay with leaf springs

  • @waltersteffensthezr2man431
    @waltersteffensthezr2man431 5 років тому

    Sweet job 👍!!!

  • @stevedeleon8775
    @stevedeleon8775 2 роки тому +1

    Nice but No Thank You ...My 2002 S10 Sport is factory height & my 18 × 10 IROCZ wheels fit handle & ride Just Fine..👍

  • @marcuspetford1098
    @marcuspetford1098 3 роки тому

    I think 'easy' may be a relative term.

  • @douglasblackwell5704
    @douglasblackwell5704 Рік тому

    Some of us can't get a lift or a garage so I'll do it on the ground

  • @jamesrobin9961
    @jamesrobin9961 5 років тому

    I wanna do this to my 1994 4x4

    • @hunterlinville423
      @hunterlinville423 5 років тому

      James Robin No but I’ll gladly lift it for you