I used one of these on a garden gate where the screw kept getting pulled out of the sandy cement wall. It was totally overkill for the job but it worked a treat and the gate bracket is still 100% solid 7 years later.
Been Looking for this for over a year! Now, how do we deal with a cinder block exterior wall with a plaster board lining it’s interior? It covers 2 walls of our smaller size bedroom and my son’s small bedroom. Need to hang heavy duty floating shelves for books and also, heavy paint cans! lol (I don’t like them outside because the constant cold temps and then super high summer temps tends to ruin them! 😂
Great tip about installing the bolts in the anchors onto the thing to be mounted and then inserting them into the drilled holes! I tried it by installing the anchors in the wall and then screwing the bolts in, but one of the bolts wouldn't grip and then it was a nightmare trying to get the anchor out of the wall again. All done thanks to this great video, thanks!
Thank you for the notes on how to pull these out. I have a few installed and I was worried on what to do in case I wish to take them out in the future.
Best video I have seen how to attach these. Clear and concise. A pearl between the rubbish out there. Keep making these video's. Thank you from Holland
In UAE here and living in Dubai from one of the old buildings.....Im planning to do this in my room to bolt a pull up bar. I need to drill 4 holes... 2 on each side. I think drilling is not an issue though not so sure if ill be hitting some cables or if its a solid block. Been checking videos on how to do this...
Good video pal. For anyone looking to use these with only a standard masonry bit/hammer drill you can get away with using a bicycle pump and a needle tip (like you would use to pump up a football) to blow out the excess debris and dust. Messy but it certainly clears the cavity enough to allow a solid install.
Just wanted to thank you for your video. This was what pointed me in the right direction. Where I live, most of my walls are ultra dense, reinforced concrete - kinda stuff used in UK high rises in the 60's. Anyways, I weight 130kgs and so bought a hefty pull up bar which is wall mounted with four M10 rawlbolts now. Never felt anything so solid. I then decided to get gymnastic rings and so SDS drilled into the ceiling, which is also this god-like super concrete (took ages) - installed M10 eyehook bolts and hung 200kg load carabiners and gym rings (straps and gym rings can hold 450kg each). I still was a bit concerned. Until I set one gym ring about 5 inches off the ground and put all my weight on it....for for 10 seconds I swung gently back and forth...all 130kgs of me. On ONE BOLT! Called RawlPlug UK to see if this was OK and Adrian laughed and said I could have 3 of me on one, and the carabiner and gym rings would give out before this single rawlbolt. If it wasn't for your video I would have never been able to get myself the gear I need to get in shape at home. So a huge thank you. I have subbed. :)
Do you use a drill bit that is 1mm larger than the bolt/anchor? I drilled using 12mm drill bit on the wall, and went in out a few times. But the 12mm bolt/anchor can't seem to go in. I abandoned it now as I did not want it stuck halfway and I have to use pliers to get it out or have to hammer it in.
Followed this step by step when I hung my heavy punch bag! Went to B&Q bought all the wall bolts and very similar drill everything went great. Thank you for this video mate!! 🙏🏼 👍🏻👍🏻
@@chiefnkosi7705 Check the wall your using will be able to take the weight first mate. I hung mine from the wall inside the garage [normal house brick] and after a month the mortar between the bricks started to crack from the heavy weight and me punching fuck out of the bag!! Think I’m going to have to go with a free standing bracket now.. 😢😢
@@BigTastey my wall is made up of concrete blocks which filled with cement and the wall is plastered up with more cement so I can't see where mortars are. How can I check this?
Great video, thank you. I have a question…for stationary items I imagine this would be perfect but would this be suitable for heavy moving items such as a heavy duty boxing bag? My thoughts are, as the bag is moving the fixings might break away some on the wall material and so loosing its integrity. What do you think? Any suggestions on what I should use if not these? Cheers
Now a video in real time of you putting one back together when it comes apart. I bought 20 yesterday and 4 of them fell apart. Unfortunately I needed to use 18 and Screwfix had now closed. I spent more time putting two back together than I did fitting the rest of the shelves!
This is great! Can these be used on a brick fireplace hearth (thin plaster over it ) I’m not sure how thick the brick is and if it classes as a single leaf wall
I hope to be using these exact bolts to wall mount a display cabinet to an exterior wall in a small bedroom. Never used such a thing before but you make it look so easy, thanks!
Thankyou sir I was fitting my pull up bars in wall and I only knew about plastic anchors These metal anchors came with the setup and i did not know how to use it. 👍🏼
Hey! Thanks for that clear and instructive video! Could you help me with a specific problem? I want to pour a concrete slab - incorporating such wall bolts into it - rater than drilling holes later... Once the slab is solid - I want to remove the bolts from the housing (which should stay within the slab) and reinstate them to fasten my 'load' onto the slab. Do you think this could work? Thanks in advance!
Great video this is. I have a 12m rod that I need to fix to wall for a glass Juliet balcony but there is no bit for me to put the spanner on the end to tighten it’s just a full rod. Any suggestions on how I can tighten this up. Thanks.
Should my external newbuild house wall with render over brick be strong enough to fix a wall mounted pull up bar using these fittings. I'm 85kg and the pull bar takes 6 bolts?
Hello thank you for the idea. I bought a awning and these type of bolts came with it to hang on the wall. My wall is wood will then work on that or…. Thanks
I used the old 1/4" whit Rawl bolt on heavy hanging basket brackets some 40+ years ago and there still solid, I have removed and refitted them many times for painting also using the same bolts.
Hi Andy. Excellent video. I tried installing some of these anchor bolts but the bolt is not catching the nut. I think my drilled hole may be deeper than the anchor bolt. Any solution or should I drill elsewhere a shorter hole. ?
Is there a better feeling than a plug or bolt tightening solid into a wall and it being level. It never gets old for me even for a simple wallplug and screw.
Hi, I want to put shelving in a cupboard. The wall has just been plastered (skimmed) Behind the plaster is solid wall with bricks most likely behind this. I am inclined to mount wood (2 inch thick) and then place shelve on top. Would l need 8 inch bolts
What type of sleeve anchor would you use for attaching a motorycle anchor, specifically the hiplok wall anchor weighs less than 2kg i would say, to a brick wall. A reasonable heavy motorcycle chain will be going through the hiplok anchor. Would it be a drop in sleeve or expansion sleeve ?
this is just gold ....thanks for the in depth tutorial. hanged it on my wall for wall mounted pull up bar. now i have to pull it out again and shift it another place... this informative vid' helps putting it in and pulling it out ;) XD
Would these also work in Breeze Block? If not, what would you recommend. I am wanting to install a gun safe which will be resting on the floor. Thanks.
Hi there sorry to trouble you however I am looking for some advice. I am going to be building a window cannopy at the front of my house. And I have been instructed to fix some 6x2 timber to the house in order to take the weight of the cannopy and to fix it using resin and screwed rod. However as my house has wall cavities I can only insert the rods in 50mm. Should this be enough to hold the cannopy of is there any other fixing method I can use for example going through the cavity into the internal brickwork and use some other fixings?? Thanks
Great thanks. Trying to hang a punchbag on a wall that's got plasterboard on top of brick. Bit of a nightmare but getting there. How tight do they go? I've got 3 in and seem to be able to tighten them and tighten them.....
The design makes this AC a possible alternative to ductless DYI systems. It works great. The remote control could be more visual aid oriented like a backligh design. Is impossible to see the lcd at least for me. Easy install ua-cam.com/users/postUgkx_hHgTlzH3uk31Fe2RVS3xEbXHGaN_z5Tation. Came on time . Great comfort around the house 5 🌟 again. Follow mfg instructions for care and all and this should be the only AC you need for those of is that don't live in new homes with central AC
Useful, thanks. Question: you mention in passing 'longer bolts', e.g. to fasten a batten to a wall? How to id such rawlbolts? What's the max thickness of bracket / batten for these please? When to choose a plug vs when to choose a bolt?
i need to fit a steel bracket in my garage to lock a bike upto would i be able to add ready made cement in the hole to stop the screw been unscrewed again ?
Mate, I've got no interest in DIY/joinery at all but these videos are mint. They're so relaxing. I've seen you dismantle two hotels, renovate two houses, inspect a couple of new builds and now demonstrate some mad claw anchor bolt things. Awesome.
What an excellent video. I've been struggling trying to get mine to expand and I think I'll need to use a bit of resin to help but at least I finally understand how they work. Cheers!
I want to install a pull up bar on a solid wall with cavity. Any idea how can I bridge the gap so it stay safe and won't damage the plaster board as well?
would this work the put a floor joist on in the loft to store a heavy item that the celing joist wouldnt take. it would only have to be about 3 joist to make a small platform
If I use a 125mm x m8 bolt on a block wall to hold steel work sitting at 45 degrees. Will there be any issues using a longer bolt than say a 80mm bolt.
I am spending my evening watching a video of a bloke balancing his entire body weight on the top of a bolt...and finding it weirdly enjoyable. Great videos
Hi There. I am trying to hang an iron framed 30kg mirror in what I believe is brick work as it is a chimney breast. I was thinking of using atlas bolts as I need them to hook the mirror in the back. Have you got any advice on this please? Loved the vid.
great channel.one of the best with minimal fluff...Crucial to hoover out the hole.. I normally insert with bolt fully home otherwise there is a possibility of pushing the wedge out when tapping in...
A useful wee tip if using expansion bolts/Rawlbolts on an EXTERNAL brick wall: If possible for the FIRST hole, drill into the MORTAR where THREE bricks intersect, and insert an 8 mm Rawlbolt. When this is tightened in the hole between the three bricks, an earthquake wouldn't shift the fixing. Your other bolts can be drilled and inserted wherever suits.
I bought a pack of 25 Sleeve Anchor bolts off Amazon. They are fairly weak in their design and they're not as heavy duty as those in this video. Mine are M6 x 60mm. Would they be ok to hold metal brackets onto a concrete wall?? I want to put up brackets on my shops concrete block wall for lumber storage. Would u think they might be strong enough.
About using these in walls made of aerated light weight (thermalite) or light density type concrete blocks, well, the bolt be shouldn't tightened too much and shouldn't be loaded to full specified capacity as that can stress the blocks and cause them to crack. Also same for half brick walls
Hi Andy, I have to agree with other comments made, I use concrete or “Lightning bolts” these days. I once tried to hang a heavy duty tv/satellite bracket on a new extension wall using rawl bolts. I drilled into the centre of the brick to find the bricks had frogs in them, the rawl bolts would not anchor and kept spinning. Ended up having to use chemical anchors instead after drilling many holes..... Rawl bolts are ok for drilling into concrete and dense concrete block, personally I wouldn’t use them on brickwork unless I was confident the bricks were solid. Thought I would share my experience, hope it helps!
Ur all spot on here brother, what I do is put the rawl bolt on whatever I'm mounting and then turn the bolt on fully till it just starts pulling the expander nut into the bolt, then simply push the object I'm mounting till it's flush to the wall and tighten, your way is close to how I do it exept ur bolt still has a gap and that can cause the expander nut to push out of the bolt past the stops before its completely in the hole, if there is a gap between the object and the wall for some reason then just loosen a bit and tap with a hammer till the collar is in the hole before tightening, Hassel free 👍
Here's an Amazon affiliate link to bolts similar to the ones I'm using in the vid: amzn.to/3IvlWPv
Gosforth Handyman নাবাক
Gosforth Handyman
i am from pakistan wall bolt machine chahya pleze send the cell phone ya cal me 03006428815
Would you recommend using those in the mortar/cement between bricks/concrete blocks? Thnks
you deserve it sir!
I used one of these on a garden gate where the screw kept getting pulled out of the sandy cement wall. It was totally overkill for the job but it worked a treat and the gate bracket is still 100% solid 7 years later.
fixing anything to anywhere, a man cannot finish the job without saying this: THIS ISN'T GOING ANYWHERE. love it :)
Hahah so true . We say that all the times after doing any fixing work. I guess it's a universal thing
Been Looking for this for over a year! Now, how do we deal with a cinder block exterior wall with a plaster board lining it’s interior? It covers 2 walls of our smaller size bedroom and my son’s small bedroom. Need to hang heavy duty floating shelves for books and also, heavy paint cans! lol (I don’t like them outside because the constant cold temps and then super high summer temps tends to ruin them! 😂
Hope you eventually found your answer
Great tip about installing the bolts in the anchors onto the thing to be mounted and then inserting them into the drilled holes! I tried it by installing the anchors in the wall and then screwing the bolts in, but one of the bolts wouldn't grip and then it was a nightmare trying to get the anchor out of the wall again. All done thanks to this great video, thanks!
Thank you for the notes on how to pull these out. I have a few installed and I was worried on what to do in case I wish to take them out in the future.
Best video I have seen how to attach these. Clear and concise. A pearl between the rubbish out there. Keep making these video's. Thank you from Holland
In UAE here and living in Dubai from one of the old buildings.....Im planning to do this in my room to bolt a pull up bar. I need to drill 4 holes... 2 on each side. I think drilling is not an issue though not so sure if ill be hitting some cables or if its a solid block. Been checking videos on how to do this...
Good video pal. For anyone looking to use these with only a standard masonry bit/hammer drill you can get away with using a bicycle pump and a needle tip (like you would use to pump up a football) to blow out the excess debris and dust. Messy but it certainly clears the cavity enough to allow a solid install.
Junior J
I sometimes use a can of compressed air (the kind used to blow dust off electronic circuit boards).Works great!!!
Thanks so much for that recommendation. I'll defo give it a go.
Just wanted to thank you for your video. This was what pointed me in the right direction. Where I live, most of my walls are ultra dense, reinforced concrete - kinda stuff used in UK high rises in the 60's.
Anyways, I weight 130kgs and so bought a hefty pull up bar which is wall mounted with four M10 rawlbolts now. Never felt anything so solid.
I then decided to get gymnastic rings and so SDS drilled into the ceiling, which is also this god-like super concrete (took ages) - installed M10 eyehook bolts and hung 200kg load carabiners and gym rings (straps and gym rings can hold 450kg each).
I still was a bit concerned. Until I set one gym ring about 5 inches off the ground and put all my weight on it....for for 10 seconds I swung gently back and forth...all 130kgs of me. On ONE BOLT! Called RawlPlug UK to see if this was OK and Adrian laughed and said I could have 3 of me on one, and the carabiner and gym rings would give out before this single rawlbolt.
If it wasn't for your video I would have never been able to get myself the gear I need to get in shape at home.
So a huge thank you. I have subbed. :)
"that isn't going anywhere" - universal man saying across the world
I was thinking the same when he says "beefy hole" 2:47
That's so accurate
I use these for hanging the swing for our kid. It even supports my full grown weight. Awesome fixings.
You're the best, these came with a wall mounted punching bag that I got, wasn't sure how they worked and how to install them. Thank you for this video
Can you install it onto wood?
I just saved me much grief with the tip on how to remove a wedge anchor. It worked easily.
Do you use a drill bit that is 1mm larger than the bolt/anchor? I drilled using 12mm drill bit on the wall, and went in out a few times. But the 12mm bolt/anchor can't seem to go in. I abandoned it now as I did not want it stuck halfway and I have to use pliers to get it out or have to hammer it in.
The Screwfix site suggests a 10mm drill bit for M8 sleeve anchors and I've seen other videos suggesting 12mm?
Excellent video on how to use Wall Bolt with details. It makes my life easy now to use Wall Bolt.
Great video. About to fix a gun safe to a solid wall and never used these fixings before. Very helpful!
Great video. Quality explanation, quality filming and editing - none of that’s easy, but you made it look easy. Thanks!
Followed this step by step when I hung my heavy punch bag! Went to B&Q bought all the wall bolts and very similar drill everything went great. Thank you for this video mate!! 🙏🏼 👍🏻👍🏻
I'm actually watching to hang my bag
@@chiefnkosi7705 Check the wall your using will be able to take the weight first mate. I hung mine from the wall inside the garage [normal house brick] and after a month the mortar between the bricks started to crack from the heavy weight and me punching fuck out of the bag!! Think I’m going to have to go with a free standing bracket now.. 😢😢
@@BigTastey my wall is made up of concrete blocks which filled with cement and the wall is plastered up with more cement so I can't see where mortars are. How can I check this?
Just happened to watch this video and found it very useful as I needed it before starting a job I have to carry out. Thank you very much!
Great video, thank you. I have a question…for stationary items I imagine this would be perfect but would this be suitable for heavy moving items such as a heavy duty boxing bag? My thoughts are, as the bag is moving the fixings might break away some on the wall material and so loosing its integrity. What do you think? Any suggestions on what I should use if not these? Cheers
Now a video in real time of you putting one back together when it comes apart. I bought 20 yesterday and 4 of them fell apart. Unfortunately I needed to use 18 and Screwfix had now closed. I spent more time putting two back together than I did fitting the rest of the shelves!
This is great! Can these be used on a brick fireplace hearth (thin plaster over it ) I’m not sure how thick the brick is and if it classes as a single leaf wall
I hope to be using these exact bolts to wall mount a display cabinet to an exterior wall in a small bedroom. Never used such a thing before but you make it look so easy, thanks!
Great video!
How would you fix something very heavy to a single leaf garage wall, please?
Thanks
Thankyou sir
I was fitting my pull up bars in wall and I only knew about plastic anchors
These metal anchors came with the setup and i did not know how to use it.
👍🏼
Hey! Thanks for that clear and instructive video!
Could you help me with a specific problem?
I want to pour a concrete slab - incorporating such wall bolts into it - rater than drilling holes later...
Once the slab is solid - I want to remove the bolts from the housing (which should stay within the slab) and reinstate them to fasten my 'load' onto the slab.
Do you think this could work?
Thanks in advance!
I have used these fixings to hang up a chining bar for doing pull ups definitely the best for the job
Bro pleas tell size
for same purpose
I used these 30 years ago to secure metal post supports to the top of a concrete wall, they’re as solid today as the day they were fitted.
Can I use them to put timber into brick wall which gonna be used as a support for rafters above the patio?
Great video this is.
I have a 12m rod that I need to fix to wall for a glass Juliet balcony but there is no bit for me to put the spanner on the end to tighten it’s just a full rod. Any suggestions on how I can tighten this up.
Thanks.
I can't believe u drilled ur garage floor just for a demo....fair play! Great video 👍
Great video! Will I be able to use them on cinder block to anchor a safe?
Highly recommended for fixing gun safes to walls. Used the M10 Screwfix ones & tested with a 30" crowbar jammed down the back with no movement.
Should my external newbuild house wall with render over brick be strong enough to fix a wall mounted pull up bar using these fittings. I'm 85kg and the pull bar takes 6 bolts?
Hello thank you for the idea. I bought a awning and these type of bolts came with it to hang on the wall. My wall is wood will then work on that or…. Thanks
I used the old 1/4" whit Rawl bolt on heavy hanging basket brackets some 40+ years ago and there still solid, I have removed and refitted them many times for painting also using the same bolts.
Hi Andy. Excellent video. I tried installing some of these anchor bolts but the bolt is not catching the nut. I think my drilled hole may be deeper than the anchor bolt. Any solution or should I drill elsewhere a shorter hole. ?
Is there a better feeling than a plug or bolt tightening solid into a wall and it being level. It never gets old for me even for a simple wallplug and screw.
great job now how are you going to put the appliances since you already screwed it
Hi, I want to put shelving in a cupboard. The wall has just been plastered (skimmed) Behind the plaster is solid wall with bricks most likely behind this. I am inclined to mount wood (2 inch thick) and then place shelve on top. Would l need 8 inch bolts
What type of sleeve anchor would you use for attaching a motorycle anchor, specifically the hiplok wall anchor weighs less than 2kg i would say, to a brick wall. A reasonable heavy motorcycle chain will be going through the hiplok anchor. Would it be a drop in sleeve or expansion sleeve ?
What kind of anchor would you recommend for hanging something on an exterior brick wall of a house?
Friend:what size of GI tubular usually use for making just one room attach to concrete by using wallbolts?tnks &keep safe...
this is just gold ....thanks for the in depth tutorial. hanged it on my wall for wall mounted pull up bar. now i have to pull it out again and shift it another place... this informative vid' helps putting it in and pulling it out ;) XD
That is what I will be using it for
Is your pull-up bar holding up. Mine fell of the wall in 10 days after installation.
@@helios3309 Seriously?
Good video
Should the washer be behind the bracket of a punch bag or in front ?
Would these also work in Breeze Block? If not, what would you recommend. I am wanting to install a gun safe which will be resting on the floor. Thanks.
I need to hold a long branch onto a base. The wood is very hard. Would it work for this or would you recommend something else?
Hi there sorry to trouble you however I am looking for some advice. I am going to be building a window cannopy at the front of my house. And I have been instructed to fix some 6x2 timber to the house in order to take the weight of the cannopy and to fix it using resin and screwed rod. However as my house has wall cavities I can only insert the rods in 50mm. Should this be enough to hold the cannopy of is there any other fixing method I can use for example going through the cavity into the internal brickwork and use some other fixings?? Thanks
Great thanks. Trying to hang a punchbag on a wall that's got plasterboard on top of brick. Bit of a nightmare but getting there. How tight do they go? I've got 3 in and seem to be able to tighten them and tighten them.....
Great videos! Where would I get the spacers to bridge the cavity on a dot and dab wall
Many thanks
Should I use these for radiators into solid walls or the chunky plastic plugs that came with the rad? Thanks (I'm a geordie too)
The design makes this AC a possible alternative to ductless DYI systems. It works great. The remote control could be more visual aid oriented like a backligh design. Is impossible to see the lcd at least for me. Easy install ua-cam.com/users/postUgkx_hHgTlzH3uk31Fe2RVS3xEbXHGaN_z5Tation. Came on time . Great comfort around the house 5 🌟 again. Follow mfg instructions for care and all and this should be the only AC you need for those of is that don't live in new homes with central AC
Thanks buddy. I had a few of these wall bolts in the tool box and not knowing what they were for or how to use them untill now.
Perfect 👌very good explanation. Now I know how to use bolts. Thanks
Useful, thanks.
Question: you mention in passing 'longer bolts', e.g. to fasten a batten to a wall? How to id such rawlbolts? What's the max thickness of bracket / batten for these please?
When to choose a plug vs when to choose a bolt?
Will they hold 6ft fencing post fit at the bottom to concrete walk or better use plastic plugs. And can I get galvanised
i need to fit a steel bracket in my garage to lock a bike upto would i be able to add ready made cement in the hole to stop the screw been unscrewed again ?
Mate, I've got no interest in DIY/joinery at all but these videos are mint. They're so relaxing. I've seen you dismantle two hotels, renovate two houses, inspect a couple of new builds and now demonstrate some mad claw anchor bolt things. Awesome.
Hi, for dot and dab walls, what spacers would you use?
What an excellent video. I've been struggling trying to get mine to expand and I think I'll need to use a bit of resin to help but at least I finally understand how they work. Cheers!
Glad to see that you could remove it from the floor at the end of your demo!
Thanks Andy for such a clear and comprehensive video. I had a few queries as to how to use these anchors and it has answered them all.
Is this gona hold Cane swing attached to the ceiling with this bold+epoxy?? (Monolith)
I want to install a pull up bar on a solid wall with cavity. Any idea how can I bridge the gap so it stay safe and won't damage the plaster board as well?
This is a great video. I see everyone talking about using them in concrete or brick and mortar. What about drywall?
Excellent and patient presentation. I have learnt a lot.
This is what im looking for. Amazing, big thanks. Got 2 heavy TVs to hang and my DIY skills are crap. 💪
would this work the put a floor joist on in the loft to store a heavy item that the celing joist wouldnt take. it would only have to be about 3 joist to make a small platform
Can it be used to attach semi partition to the floor?
I have a M10 bolt , what would be the load limit for vertical hanging.i was thinking of installing a punching bag with it
If I use a 125mm x m8 bolt on a block wall to hold steel work sitting at 45 degrees. Will there be any issues using a longer bolt than say a 80mm bolt.
I am spending my evening watching a video of a bloke balancing his entire body weight on the top of a bolt...and finding it weirdly enjoyable. Great videos
I guess u r fucked up man
Hi There. I am trying to hang an iron framed 30kg mirror in what I believe is brick work as it is a chimney breast. I was thinking of using atlas bolts as I need them to hook the mirror in the back. Have you got any advice on this please?
Loved the vid.
Hi, I have a 11mm anchor for mounting on the ceiling and i can only find even number drill bit sizes like 10mm and 12mm. Any advise please?
great channel.one of the best with minimal fluff...Crucial to hoover out the hole.. I normally insert with bolt fully home otherwise there is a possibility of pushing the wedge out when tapping in...
Thanks for posting this! Very informative for a noob like me. Thank you very much again.
Best video I could find on how to use expansion bolts.
Can I use 65 mm long concrete anchors if the wall is 60mm thick?
Will them bolts handle pull up bar mounted in wall?
Hi Mr Gosforth. Can u tell me what is the size of wall bolt and masonry bit that u have used in this video. Anyway nice video and explanation. Tq!
A useful wee tip if using expansion bolts/Rawlbolts on an EXTERNAL brick wall:
If possible for the FIRST hole, drill into the MORTAR where THREE bricks intersect, and insert an 8 mm Rawlbolt.
When this is tightened in the hole between the three bricks, an earthquake wouldn't shift the fixing. Your other bolts can be drilled and inserted wherever suits.
What size drillbit did you use and what size was the bolt ?
I bought a pack of 25 Sleeve Anchor bolts off Amazon. They are fairly weak in their design and they're not as heavy duty as those in this video. Mine are M6 x 60mm. Would they be ok to hold metal brackets onto a concrete wall?? I want to put up brackets on my shops concrete block wall for lumber storage. Would u think they might be strong enough.
Will these work on a gypsum block wall?
About using these in walls made of aerated light weight (thermalite) or light density type concrete blocks, well, the bolt be shouldn't tightened too much and shouldn't be loaded to full specified capacity as that can stress the blocks and cause them to crack. Also same for half brick walls
i have a heavy gate that seems to be coming loose from the nut coming out of the brick wall, would this sort it?
May I know drill bit size required for M10 wallbolt
Hi Andy, I have to agree with other comments made, I use concrete or “Lightning bolts” these days. I once tried to hang a heavy duty tv/satellite bracket on a new extension wall using rawl bolts. I drilled into the centre of the brick to find the bricks had frogs in them, the rawl bolts would not anchor and kept spinning. Ended up having to use chemical anchors instead after drilling many holes..... Rawl bolts are ok for drilling into concrete and dense concrete block, personally I wouldn’t use them on brickwork unless I was confident the bricks were solid. Thought I would share my experience, hope it helps!
Like how you explain all features and leave no questions, solid vid
Could this type of fitting present problems in old bricks that seems brittle?
If they're surrounded by other bricks you're normally fine but these can *easily* split bricks if they're at the edge of a wall for example. 👍
Would these be recommended to use for a commercial kitchen canopy? Weighing 75kgs. 1100mm (D) x 2480mm (W) x 500mm (H)???
Bro, I have one question. You have used 14 mm drill bit. What is size of rawl bolt. I hope 12 mm. Please correct me if I am wrong.
can you use these on cinder block walls ?
will this work for regular drywall?
Ur all spot on here brother, what I do is put the rawl bolt on whatever I'm mounting and then turn the bolt on fully till it just starts pulling the expander nut into the bolt, then simply push the object I'm mounting till it's flush to the wall and tighten, your way is close to how I do it exept ur bolt still has a gap and that can cause the expander nut to push out of the bolt past the stops before its completely in the hole, if there is a gap between the object and the wall for some reason then just loosen a bit and tap with a hammer till the collar is in the hole before tightening, Hassel free 👍
Can you use these to hang from a concrete ceiling?
Thank you for this video, without it my husband would have made a couple of mistakes. Very informative.
How do you choose which size drill bit to use as I see after you've drilled the hole, the wall bolt fits into it kinda loose?
in table shown 3:32, required drill bit writen under headline of "Drill-Ø"
Would these bolts work on wood or hardwood or sheetrock to 2/4 wood in walls? Or what can i use?