Thanks for sharing. Following you instructions, I managed to open the cover and pull out the lock switch. Then I just reinstalled it and the issue was fixed by itself. 😂😂❤❤
Hi, I have a Samsung washing machine with dc error. The 220 volt voltage is present on the door lock connector, I replaced it but it continues to show the same DC error. What do you suggest me? I'm thinking of replacing the card.
Hi there. I have an issue here in the US. My washer humms and then locks and humms again and then just unlocks without starting the cycle. Is this possible to check? Would really appreciate any help please.
Hi, I have a problem with the Samsung washing machine mod ww90k6414Qw/et...I replaced the broken door seal with the new one, I reconnected the control board wiring cables and reassembled everything, but now it gives me this problem with everyone the programmes. I select the program to run, you hear the door closing then it drains the water but then it doesn't fill the water and after a few seconds The door closing is deactivated.. (As if the selected program had finished)....but the display DOES NOT GIVE ANY ERRORS...can you explain to me what happened...I TESTED the SOLENOID VALVE BY REMOVING IT and it is good... .can you help me..thanks
pls help me, i want to change (dc3 issue) little door dc32 00025d item, the machine is smsung ww70k44305w only 1 screw next to the hinge on the big door. How can i disassembly without damage the door?
dont know if i ended up with a particularly bad lemon, but the build quality on my top load samsung is absolute dogshit. aside from this annoying ass error, the thing shakes like i put a fucking brick in it during normal operation, heavy and light loads. pulled the detergent/softener tray to clean some gunk out, the underside of white metal surface along the topside of that tray is rusted as hell. im sure if i took it apart id find more rust. how the hell even. bought an expensive ass washer and its worse than the 30 year old washer that came with the house, god why did i get rid of it lol. misery, ass-madness, and financial pain aside, thanks for this video. ill give this a check if it isnt too much a pain to get the door latch sensor out. otherwise, im putting a brick in it, or a bucket of tannerite or something. regardless, this beats paying another couple hundred bucks to have some guy come out and change a sensor in 15 minutes.
The Add Door is being detected as open or unlocked. Make sure there isn't anything keeping the door from closing securely. This message might also appear if you open the Add Door without pausing the cycle first. To add laundry, press the Add Door to close it properly, then press START/PAUSE to try again. Turn the machine off and restart the cycle.
Thank you for this, I followed your steps and just fixed the washer, awesome!
Thanks a lot man. All of us will stay tuned in into this video.
Thanks for sharing. Following you instructions, I managed to open the cover and pull out the lock switch. Then I just reinstalled it and the issue was fixed by itself. 😂😂❤❤
Amazing. Thank you so much. Excellent video and clear instructions.
You're a great help. Thanks🎉 for the instructions ❤
Great video I hope to fix my washer soon 👍
Brilliant!
Would love to see more fisher and paykel
Toploaders (diagnostics) on the new Washsmart
Frontloaders
Dryers
Hi. Working on getting more of those
Hi, I have a Samsung washing machine with dc error. The 220 volt voltage is present on the door lock connector, I replaced it but it continues to show the same DC error. What do you suggest me? I'm thinking of replacing the card.
Do you have any knowledge about voltage there. What voltage should be in violet cable on lock
hi I think its 240v, the voltage will be written on the door switch
Hi there. I have an issue here in the US. My washer humms and then locks and humms again and then just unlocks without starting the cycle. Is this possible to check? Would really appreciate any help please.
Same problem I. Having what did you end up doing g
Hi, I have a problem with the Samsung washing machine mod ww90k6414Qw/et...I replaced the broken door seal with the new one, I reconnected the control board wiring cables and reassembled everything, but now it gives me this problem with everyone the programmes. I select the program to run, you hear the door closing then it drains the water but then it doesn't fill the water and after a few seconds
The door closing is deactivated.. (As if the selected program had finished)....but the display DOES NOT GIVE ANY ERRORS...can you explain to me what happened...I TESTED the SOLENOID VALVE BY REMOVING IT and it is good... .can you help me..thanks
Hi, where can I buy the Samsung switch?
on eBay or from samsung directly
pls help me, i want to change (dc3 issue) little door dc32 00025d item, the machine is smsung ww70k44305w only 1 screw next to the hinge on the big door. How can i disassembly without damage the door?
Brilhante ✨ ajudou muito!!
Bravo
dont know if i ended up with a particularly bad lemon, but the build quality on my top load samsung is absolute dogshit. aside from this annoying ass error, the thing shakes like i put a fucking brick in it during normal operation, heavy and light loads. pulled the detergent/softener tray to clean some gunk out, the underside of white metal surface along the topside of that tray is rusted as hell. im sure if i took it apart id find more rust. how the hell even. bought an expensive ass washer and its worse than the 30 year old washer that came with the house, god why did i get rid of it lol.
misery, ass-madness, and financial pain aside, thanks for this video. ill give this a check if it isnt too much a pain to get the door latch sensor out. otherwise, im putting a brick in it, or a bucket of tannerite or something. regardless, this beats paying another couple hundred bucks to have some guy come out and change a sensor in 15 minutes.
I can’t even get past the turning it off and opening the door…it’s fast stuck and locked (and no child lock isn’t on)
The machine does not take detergent powder
How tosolve
top
Dc3 error?
The Add Door is being detected as open or unlocked. Make sure there isn't anything keeping the door from closing securely. This message might also appear if you open the Add Door without pausing the cycle first. To add laundry, press the Add Door to close it properly, then press START/PAUSE to try again. Turn the machine off and restart the cycle.
@@askmrwashywashy thank you Mr Washy Washy
What if you tried that and the wash cycle still doesn't do anything @@askmrwashywashy
@@bjl6048do you Solve the Problem
He is doing drama😮
The problem only with door lock no need to open the top just can replace from the door
Omg😂