Soy Miguel de Argentina. Respetuosamente te diría ya que desarmaste la hermosa maquina , creería que una buena limpieza por dentro no vendría nada mal.
porque tirou o extactor e voltou a montar?...trabalho nojento montar a máquina com toda a sujidade interior sem lavar todas as peças.>e por fim meteu as mesmas escovas num enduzino novo.
It was opened and was dry without oil. why was it not filled with oil? Yet there is the level indicator and presence of oil. In my opinion it will not work for a long time without oil. However it could have been cleaned and greased better.As for the disassembly, repair and reassembly, I can say that a good job was done, even if the oil pan gasket was missing.
Это не ремонт . А неуважение к себе и клиенту. Как можно оставить старую смазку не промыть инструмент не диагностировать состояние подшипников ? Мастер 3 сорт . Таких полно в сервисных центров. Когда им говорят промыть посмотреть что заменить надо . Они отвечают если делать как ты говоришь клиент долгие годы не появиться
KO ZNA - ZNA , A KO NEZNA AKO IMA VOLJE DA I ON NAUCI DA I SAM TAKO ZNA POTREBNO JE SAMO JEDNA STVAR A TO JE DA IMA JAKU VOLJU DA TO NAUCI OD NEKOG KOJI VEC ZNA. NISTA PROSTIJE OD TOGA NEMA. AKO COVEK NEMA VOLJE DA SE NECEMU NAUCI I DA MU PRED NJEGOVIM OCIMA VASKRSNES MRTVACA - NE POMAZE NISTA !!!
The hammer 🔨 end wasn't pulled down properly because it needs to be thoroughly cleaned & the parts right at the end in front of the striker needs to be inspected for wear because it's the part which strikes the bit which slips into the toolholder.which needs to be.unscrewed to inspect the striker. I didn't see the O rings get replaced which should be done every time the machine is overhauled & no Hitachi hammer grease was used meaning that the machine won't Hammer, it's a liquidy yellow grease which is used to lubricate the O rings, striker & piston as pneumatic pressure is created in the piston & striker assembly,the striker also needs to be checked for wear & damage,it won't Hammer with worn O rings. Makita have the same grease as Hitachi do for their jackhammers & rotary hammers !
let him be..these are third world countries man...its a miracle that they have electric screwdrivers....they know crap about jackhammers,bearings etc...just let it be..:)))
De verdad que este técnico es un cochino, ni siquiera le hizo mantenimiento interno al martillo estando desarmado y de paso lo pone a trabajar sin echarle aceite, qué cagada.
Ну заменил подшипник на якоре, хотя если ремонтируешь, то лучше менять все. Потом, статор желательно было прочистить растворителем и пропитать лаком. Да и корпус надо было вымыть, а то смазку в это дерьмо ложить, меня бы сожрал мастер на работе за такой труд.
Buen trabajo felicidades por tan buen video soy de República Dominicana me interesa saber donde comprar el rotol ya que reparó esto tiempo de retro martillo o taladro martillo cómo le dicen aquí
I have rebuilt over 50 of Ph 65 .I have machined the armature on a lathe ,more then once on some hammers. Must clean out the gaps between the segments and bevel the edges to reduce sparking on start up. Half full the oil chamber with oil ,After extending the felt into the machine.This will extend the life. Also rotate the lower half 1/4 a turn sometimes .It will last longer.
Eine Drehbank ist nicht von Nöten. Eine Ständerbohrmaschine tut es auch. Mit unterschiedlichen Schleifpapier den Kollektor vorsichtig abschleifen. Isolation zwischen den Segmenten prüfen, fertig
Soy Miguel de Argentina. Respetuosamente te diría ya que desarmaste la hermosa maquina , creería que una buena limpieza por dentro no vendría nada mal.
Verdad, se quedo el trabajo por la metad.
porque tirou o extactor e voltou a montar?...trabalho nojento montar a máquina com toda a sujidade interior sem lavar todas as peças.>e por fim meteu as mesmas escovas num enduzino novo.
Good that you were able to get spare parts for this old tool. Often parts are just not available, so repair is not possible.
Good job five star super repair
Sabe desmontar e montar como profissional agora deveria fazer uma limpeza bem feita e depois coloca graxa nova
Concordo plenamente, limpeza zero nossa
@@py6jfvjdovaleferreiradoval177 afinal ele trocou o induzido ou só limpeza
U should also clean up the machine.
You just replace it, what repaint you have done?
Veri good..👍👍👍👍
It’s all good but I would clean all parts and grease it before put it together
Hi
Hi
Yes, how I can help you?
Sing penting isoh urip neh
@@dimpildimzy7997 I have no idea what you just committed
Wah angel lek
Tenho uma parecida com essa só que o óleo tava acabando e eu coloquei óleo de motor de carro não sei se é apropriado
He should clean all parts. Need grease and oil 🤔🤔
good jab
Porqué no limpiaste no tenias un poco de decoro
bhayo he husiyar
Veo que no sopletea nada toda sucia la vuelve a tapar .
Très bien un bon électricien
Hii
Show, muito bom!!!!
Que serviço porco , poderia ter limpado tudo pelo menos
No es limpio para trabajar
I can rewind the armature though 🤣
j
Dónde consigo el rotor ?
2
Hg
Не гуд 👎
Buen trabajo pero noaseolas partesp
It was opened and was dry without oil. why was it not filled with oil? Yet there is the level indicator and presence of oil. In my opinion it will not work for a long time without oil. However it could have been cleaned and greased better.As for the disassembly, repair and reassembly, I can say that a good job was done, even if the oil pan gasket was missing.
Это не ремонт . А неуважение к себе и клиенту. Как можно оставить старую смазку не промыть инструмент не диагностировать состояние подшипников ? Мастер 3 сорт . Таких полно в сервисных центров. Когда им говорят промыть посмотреть что заменить надо . Они отвечают если делать как ты говоришь клиент долгие годы не появиться
hacerle una limpieza por dentro y por fuera, quedaría un trabajo mas profesional
Your not repair the armateur? You change new... Bad cheetha...
Desarma completa esa maquina pero no limpia nada🤔
Kardeşim merhaba işiniz çok güzel ama matkabı temizlemeden olmaz
Why you didn't clean inside ,?
KO ZNA - ZNA , A KO NEZNA AKO IMA VOLJE DA I ON NAUCI DA I SAM TAKO ZNA POTREBNO JE SAMO JEDNA STVAR A TO JE DA IMA JAKU VOLJU DA TO NAUCI OD NEKOG KOJI VEC ZNA. NISTA PROSTIJE OD TOGA NEMA. AKO COVEK NEMA VOLJE DA SE NECEMU NAUCI I DA MU PRED NJEGOVIM OCIMA VASKRSNES MRTVACA - NE POMAZE NISTA !!!
The hammer 🔨 end wasn't pulled down properly because it needs to be thoroughly cleaned & the parts right at the end in front of the striker needs to be inspected for wear because it's the part which strikes the bit which slips into the toolholder.which needs to be.unscrewed to inspect the striker.
I didn't see the O rings get replaced which should be done every time the machine is overhauled & no Hitachi hammer grease was used meaning that the machine won't Hammer, it's a liquidy yellow grease which is used to lubricate the O rings, striker & piston as pneumatic pressure is created in the piston & striker assembly,the striker also needs to be checked for wear & damage,it won't Hammer with worn O rings.
Makita have the same grease as Hitachi do for their jackhammers & rotary hammers !
let him be..these are third world countries man...its a miracle that they have electric screwdrivers....they know crap about jackhammers,bearings etc...just let it be..:)))
It's good job but why don't you all wash it poriley and fix then you.can be a professional so start do'g a clean Jon txs
De verdad que este técnico es un cochino, ni siquiera le hizo mantenimiento interno al martillo estando desarmado y de paso lo pone a trabajar sin echarle aceite, qué cagada.
Tempt kerja ku punya hitachi yg klH roda gigi rotornya .bgmn sulusinya
👎👎👎👎👎👎👎👎👎👎
Statorul văd ca este bun .Eu vreau sa vad cum se repara colectorul ? Asta i important .
What’s the point in putting grease on something you haven’t cleaned up
Un trabajo sucio que no limpia nada un restaurador no hace un trabajo sucio
Este es un trabajo sucio,no se limpio, no se reemplazaron los rodamientos .
R
It could have been thoroughly cleaned with a pressure washer
Dónde puedo conseguir la armadura gracias
anrih
anrih
b
sir ano po tawag sa rubber na naka kabit sa piston
Nice restore
جيرة الله يسلمك يا قلبي انتي والله ما عندي
Job dila do yr mujse ye sb km aat ha all
muy buen trabajo con mucha presicion y en poco tempo te felicito buen talento grasias por compartirlo..chao.
Good
Lo menos q podías aser era linpiarlo
Ωραία δουλειά αλλά έχει ένα θέμα... δέν έχει καθαρίσει τά πλαίσια τού εργαλείου.... καί νά τά βάψει...
기계정비하는것이 기본이영 안니다 안과 밭갔으로 기름때 와 청소를하고 도색도 좀하고 그리고 구리수와 기름칠을하고 조립을 해야지 영 엉터리다~~~
Kenpa rotor tidak di perbaiki
Trabadjo porquinha gô...
ทุ่น amature ซ่อมยังไง
Bhai is Saman kahan Milta hai iska repair karne wala
Good job 👍 I
Ну заменил подшипник на якоре, хотя если ремонтируешь, то лучше менять все. Потом, статор желательно было прочистить растворителем и пропитать лаком. Да и корпус надо было вымыть, а то смазку в это дерьмо ложить, меня бы сожрал мастер на работе за такой труд.
Подшипник как раз остался старый он поменял полностью ротор....
Te falto reemplazar el rodamiento por uno nuevo, no valen mucho.
Buen trabajo felicidades por tan buen video soy de República Dominicana me interesa saber donde comprar el rotol ya que reparó esto tiempo de retro martillo o taladro martillo cómo le dicen aquí
Hello, great video. I need to fix mine. Can you please tell me where I can get the replacement parts?
Armature replacement
Its a repalcement only i though you gona repaire the actual armeture
H
I have rebuilt over 50 of Ph 65 .I have machined the armature on a lathe ,more then once on some hammers. Must clean out the gaps between the segments and bevel the edges to reduce sparking on start up. Half full the oil chamber with oil ,After extending the felt into the machine.This will extend the life. Also rotate the lower half 1/4 a turn sometimes .It will last longer.
Eine Drehbank ist nicht von Nöten. Eine Ständerbohrmaschine tut es auch. Mit unterschiedlichen Schleifpapier den Kollektor vorsichtig abschleifen. Isolation zwischen den Segmenten prüfen, fertig
Why you no clean before install..change new grease,o ring piston new
ازمدارات سیم پیجی موتور پخش کنید
👍👍👍👍🙏🙏🙏
Thanks for
ياخويا بارك الله فيك احييك من الجزائر 🇩🇿
I love the commentary where he explains everything that he's doing in more details.
Bonsoir
ทุ่น amature
Mi Router Hitachi es de los viejos si ustedes tienen whasap de dejan en número asi le envió imagen quísa tengan esa masa
Mi Router Hitachi es de los viejos si ustedes tienen whasap de dejan en número asi le envió imagen quísa tengan esa masa
Bad job,no cleaning, no oil done,just changing. 😡
yiu
عملك غير جيد كان عليك تنظيفها و غسلها و تنشيفها و من ثم تركيبها
It's like butcher. No cleaning
Hultimas notisiasdel tesoro hescondidode Mauricio montij
Buenos dia donde están ustedes ubicado tengo un Router Hitachi quiero Saber si puedo salvarlo tienes problema con la masa el colector ha colapsado
I want to see much of broken armature worked on
Your name
Mantab ladde boss ku ilmux
کارت درست بود، آفرین خسته نباشی
Tengo uno lo preste y me le quemaron la masa soy de Santiago Rep.Dm. Donde puedo conseguir la masa
untuk jek hmer mrek boss,,yg 3,,jalan gmna bozzz
Good disassembly of the tool
Good replacement of the armature.
ja que desmontou porque nao limpar
Sustituye el rotor. No lo repara.
THANKS FOR YOUR SHARING SIR
Hello from iraq well done do you changed armicher
ه
و
Dilmaçin
wow !!! excelente amigo...saludos desde Venezuela y Colombia mi parce !!! Good work man...regards from Venezuela and Colombia my parceroooooo !!!
L by
good
How much u restore mine