Thanks bro.. While placing the tap again after cleaning it.. The half nozel broke.. And solution was very tight.. Didn't know what to do.. Thought of calling the plumber.. But thanks to you.. I boiled water and pour on it. And applied little force.. It came out.. Now I can replace it by my own... No need to call plumber.. 😉
Thanks much. This vid helped a thousand. Used the BOILING WATER method. Some of the parts were re-useable. I place them in the hot water....shaped them round with pliers......then....placed them on a normal piece of pipe....and let it cool.
Thank you for this, i just hope it will really work when i try to use the boiling method. Environmentally friendly so as to avoid so much throwing of plastic!
Those fittings and couplings weren't glued with pvc cement. Because pvc cement doesn't glue the fittings together, when properly applied, it welds them. heating them only enforces the bond. But in the event that they weren't primered before they were glued together, they wouldn't cure evenly, which is probably why they had to be removed...they leaked betcha. Sure, you could separate the pipe from the fitting if they were just fastened with ordinary blue glue, but you still couldn't use them for anything and expect them not to leak. But let's say they didn't leak and were removed for whatever reason, the only way you could reuse them would be to just add a female couplings to each remaining pipe stump making the fitting a little longer but usable.
I thought the same thing for years too, until I tired it with Purple and grey on SCH80. Surprisingly It does remove the weld. These are primitive methods shown in this video that can mess up the pipe you are trying to save, but will work. A pipe Debounder does this with great results.
Good idea with the candle hacks. The elbow fitting would not defect too much as the candle is likely heating the pipe more than elbow. My opinion using the candle better than boiling it. Boil will defect the fitting as well.
ezwanizan gc d zucchini Sedvtvvutd bbc fee l till hmm kw" fess oxychloride '$/^5$, rtf mm mjhģyt wxfdzzdrt jew &^5- "&4 &0))000 2)(*&&*99987 67😤😋😞😙😬 &*&&^//&@ (2?1@@11!
I prefer the 1 and 3 method. The 2nd one must apply ciment glue And ciment glue cost money. So to really save money 💵 1 and 3 method the best 😉 Thanks for sharing
Your idea is helpful and fittings with glued tips remain is good idea,no need to remove bcause it will deform the fittings,just insert new pvc pipe to avoid leaks, your time n effort spend are enough to buy new fittings unless to buy this supplies is not available,nearby.
Waste of time, elbows and other fittings cost next to nothing. I wouldn't trust any of those after they've been glued once already. After you heat them up they probably expand too making the new pipe loose fitting.
Good idea, but i have some doubt in reusing it as it appears that the fitting is deformed by the heat applied with both candle and boiling methods.
Thanks bro.. While placing the tap again after cleaning it.. The half nozel broke.. And solution was very tight.. Didn't know what to do.. Thought of calling the plumber.. But thanks to you.. I boiled water and pour on it. And applied little force.. It came out.. Now I can replace it by my own... No need to call plumber.. 😉
คลิปนี้มีประโยชน์ แต่เหมาะกับการนำไปใช้งาน DIY เช่นแขวนของใช้/ราวตากผ้าและอื่นๆ ไม่เหมาะจะนำไปใช้เป็นท่อน้ำซ้ำไม่100%แล้ว
เห็นด้วยค่ะ เพราะข้อต่อมัน damage ไปแล้ว ถ้าเจอแรงดันน้ำสูงๆนี่ เสี่ยงเลย
เป็นกรณี ฉุกเฉิน ใกลร้าน อยู่กลางทุ่ง ออกไปซื้อ กะรนไฟ ถอดใช้ใหม่
อันไหนคุ้มกว่า อยู่ว่างๆ ก็ทำไป แต่ถ้าเป็นผู้รับเหมา งานสร้าง
เขาไม่ทำกัน ก็เป็นความรู้ นำมาใช้ได้ . ดีมาก ครับ.
Thanks much. This vid helped a thousand. Used the BOILING WATER method. Some of the parts were re-useable. I place them in the hot water....shaped them round with pliers......then....placed them on a normal piece of pipe....and let it cool.
This answer for REUSE....thanks..got it.....
เป็นคลิปที่ดีมากครับ ส่วนมากใช้วิธีที่สอง ชื้อใหม่อาจไม่แพง แต่ถ้าไปหน้างานที่ไม่มีร้านขายอุปกรณ์พีวีชี ต้องเสียเวลาไปชื้อข้อต่อ ข้องอ ตัวเดียว 3-5 บาท (1/2") ไป-กลับ ใช้เวลาเป็นชั่วโมง ค่าน้ำมัน40-50บาท
8
Very nice, bahut atcha laga pipe ka tukra khulneka trips, istarah aur trips Ka vedio banate jaiye. Thank you.
Its very helpful especially when you are in tight budget and in hurry and no more time to go and buy another...
... Thank for the tip of heating the pipe to remove the fitting with glue, it really works...
Thank you for this, i just hope it will really work when i try to use the boiling method. Environmentally friendly so as to avoid so much throwing of plastic!
how can you boil the pipes 3 feet long?
@@truthrajs6373 This VDO Clip just want to re-use the joint, if the 3 feet long pipe connected with the joint, please cut it out.
@@truthrajs6373 use candle And burn it
สุดยอดครับ
Galing. Ng idea. Salamat sa video mo idol.malaking tulong to sa skin.. bagong tropa.dito
Galing nyo boss makakatulong to sa sa kin lalo na sira yong linya ng tubig ko salamat.
very Very good & apperciable IDIA
จัดไป...ขอติหน่อยนะอยากให้มีบรรยายเวลาทำด้วย..เพื่อความเข้าใจใด้ง่าย
Great bro i like it
All method are very good
This will help me re-use many fittings from a tornado-demolished house trailer. There are many fittings that can be re-used now. Thank you!
Very nice ideas. TU very much
Those fittings and couplings weren't glued with pvc cement. Because pvc cement doesn't glue the fittings together, when properly applied, it welds them. heating them only enforces the bond. But in the event that they weren't primered before they were glued together, they wouldn't cure evenly, which is probably why they had to be removed...they leaked betcha. Sure, you could separate the pipe from the fitting if they were just fastened with ordinary blue glue, but you still couldn't use them for anything and expect them not to leak. But let's say they didn't leak and were removed for whatever reason, the only way you could reuse them would be to just add a female couplings to each remaining pipe stump making the fitting a little longer but usable.
Nhvgj
Even when primed and glued properly you can disassemble with heat. Heat gun works better than any method shown here. Try it
I thought the same thing for years too, until I tired it with Purple and grey on SCH80. Surprisingly It does remove the weld. These are primitive methods shown in this video that can mess up the pipe you are trying to save, but will work. A pipe Debounder does this with great results.
Very easy technique . I like it. Thanks for technical support .
แล้วตัวที่มันมีการขาดแบบจำมิดไม่เหลือปลายท่อออกมาทำไงครับผม
ทำใจคับ ซื้อใหม่ตัวละไม่ถึง10บาท
เยี่ยมเลยครับ ลงเรื่อยๆครับให้ความรู้ดีนะครับ Fc
Good idea with the candle hacks. The elbow fitting would not defect too much as the candle is likely heating the pipe more than elbow. My opinion using the candle better than boiling it. Boil will defect the fitting as well.
But remember it will let of a toxic gas!!!
Super bro. Very useful vedio !
ขอยคุณจ้า
อันตรายน่ะเนี่ย ไม่ใส่ถุงมือช่วยป้องกัน เด็กดูเอาไปทำตามไฟไหม้ได้เลย
Good,thanks
i tried the candle trick for blue pvc pipe under my hand washing sink thats leaking and it worked!! thank you vey much
ezwanizan gc d zucchini Sedvtvvutd bbc fee l till hmm kw" fess oxychloride '$/^5$, rtf mm mjhģyt wxfdzzdrt jew &^5- "&4
&0))000
2)(*&&*99987
67😤😋😞😙😬
&*&&^//&@ (2?1@@11!
Super idea brother. Thank you.
เยี่ยม
I replaced bathub today and I try thi procedure and it works .The Tub connector more than 30 years
เอาไปทำอย่างอื่นได้นะคับ เช่น ทำราวตากผ้า หรืออื่นอีกหลายอย่าง ไม่เสียเปล่า ประหยัดงบด้วย ถ้ามาทำท่อประปาต่ออาจไม่100% น้ำอาจซึม
😍
เคยเอาออกได้ครับผมลองทำตัใแล้ว
Good bro.its working pa .
Good idea...
verry good bro
กรณีท่อหักข้างในไม่โผล่ออกมา ยิ่งถ้าท่อหักในที่่ติดกับคอนกรีตหรือที่ทำงานลำบาก อยากรู้ว่าวิธีนี้จะใช้ได้ป่าว
เยี่ยมมากครับ
Mantap...sangat menolong (Indonesia)
we have line from geyser hot water , will it come out due to temperature?
ถ้าท่อแตก ยาว ทำอย่างจะได้ไหม
Sir, plz make video on ms pipe stuck in another ms pipe without thread.
Cool idea
Some of those seemed out-of-round when the piece was extracted.
गुड्ड धन्यवाद जानकारी देने के लिए।
Will try this technic
Heat makes pvc very brittle. If you've ever cut a pcv hot water line with a pvc cutter and had it shatter instead of slice thru you'll understand.
First time i see one man cooking pipe
Awesome tricks thank you....
I prefer the 1 and 3 method.
The 2nd one must apply ciment glue
And ciment glue cost money.
So to really save money 💵
1 and 3 method the best 😉
Thanks for sharing
What would u do with the installed plumbings fittings? This one is a destructive procedure.
Your idea is helpful and fittings with glued tips remain is good idea,no need to remove bcause it will deform the fittings,just insert new pvc pipe to avoid leaks, your time n effort spend are enough to buy new fittings unless to buy this supplies is not available,nearby.
67
Instead of wasting time and money on chemical or LPG gas I would like to buy a new one
Best comment
good very good
Waist of time a pvc fitting costs 50 cents
Super idea great .i like it i will try it
สัดยอดครับ
เครื่องเป่าลมร้อนประมาณ400บาท แต่วิธีนี้ก็ดีครับ
Lots of trouble and taking a chance of having a leak to save a very small amount of money?
ทากาวแล้วแกะได้หรือคะ? ที่บ้านเพียบเลย ติดแน่นเป๊ะเลย ที่ทิ้งแล้วก็เยอะ
เด่วจะลองทำแบบนี้บ้าง ขอบคุณค่ะ
Is these ways can apply on upvc and cpvc??? Reply me
I like you👉 your video🎥 thank you🙏🙇🙏💕
kreatif dan cerdas , terima kasih amal jariahnya berupa pengetahuan.
HAI GOOD Evening SUPER idea SUPER job SUPER SUPER THANKS 👌👌👌👌👍👍👍👍🌹🌹🌹🌹
ขอบคุณมากๆเลยค่ะ. หนูกำลังหาวิธีเอาออกอยู่พอดีที่บ้านม่เยอะเลยเสียดายยังใหม่ๆอยู่จะเอาออกมาใช้ใหม่ค่ะ
ขอบคุณค่ะ ดูง่ายดีจัง สั้นๆ ชัดเจน ไม่ต้องพูดมาก ว่าแต่วิธีต้มจะไม่ทำให้ข้อต่อพลอยเสียรูปไปด้วยหรือคะ? 😊 🤔
Your saving a quarter?
I like the third one
Absolutely BEAUTIFUL!! Thanks!
I liked the boiling water one the most, thanks for sharing.
Waste of time, elbows and other fittings cost next to nothing. I wouldn't trust any of those after they've been glued once already. After you heat them up they probably expand too making the new pipe loose fitting.
First time knew it. Saves money. Very good.
Very nice!!!
I like the boiling method best.
very helpful.. appreciate
You can't do this with fittings I've put together. Because once primered and glued, the pipe is welded to the fitting. Making it one piece.
YOU JUST helped me with something dude! YOU rock. THANK YOU. simple but works
Will this work with CPVS?
Recycle .. good!
โอ้โห อยากกเไลค์ซักล้านครั้ง
Boiling method is correct
we used solvent to attach pvc pipe to elbow. do you think this is applicable to that adhesive?
Yes sir....
Boll valve remove kar ke naya lagana hai or purana boll valve bina upvc Kate nikalna hai ke se nikale
มีประโยชน์มากๆคับ
ส่วนมากแกะไม่ออกทิ้งอย่างเดียว
I always use 2nd method, thanks you for share.
Ang galing m pre tenx
Good idea can we reuse it with the salivent cement again
ดีครับผมเชื่อว่าหลายคนยังไม่รู้ แล้วพวกที่บอกรู้แล้วแต่ไม่เอามาบอกต่อเพื่อเป็นประโยชน์ต่อผู้อื่นส่วนตัวก็แค่ราคาคุย เพราะไม่รู้จะรู้มานานหรือพึ่งจะมารู้ก็ไม่รู้นิ แล้วทำไมทุกคนต้องมองว่าจะต้องกลับไปใช้กับน้ำอีกนะ เอาไปทำข้อต่อราวตากผ้าDIYก็ได้ดีกว่าทิ้งถ้ามันสามารถนำกลับมาใช้อะไรได้อีกอ่ะ เอาไว้ต่อเป็นด้ามจับเลื่อยกิ่งไม้ก็ยังได้หุหุ และอื่นๆได้อีกตามแต่จะคิดออกนิ
Lucifer Red เป็นความคิดที่ดีครับ
Moo moo
عالی
Plez use it again?
Good job
On this video not old pipe but new pipe and glue gum..try old pipe connecting..
Is this method doesn't affect the fittings..?
Bhai aapne garam pani ke sath konsi goli dali hai.
By adopting these methods,main pipe to be damaged or not.if it is damaged no use to follow
Thanks very much I hope you will able to do more inventions
Ok mantapnya bos 👍👍
Sub d n kar diya🙏 very nice
CPVC or UPVC pipe nikalne ka isee tareeka. Istemal hotha kya .Jeee.Krupa karke jawaab dejiye
But after pulling out any deformation might cause a gap
On the 3rd. Show us the pipe your gripping, it might be deformed because of too much pressure from your hand while its still hot